• Journal of the Korean Applied Science and Technology
• /
• v.31 no.1
• /
• pp.74-82
• /
• 2014

For this research, prepared ammonium dihydrogen phosphate aqueous solution and polyurethane dispersion. Use these resin, this article has been analyzed about change of mechanical properties by increasing amount of ammonium dihydrogen phosphate aqueous solution in polyurethan resin on coated leather and dried film. According to measure data for solvent resistance, DPU(polyurethane dispersion) resin and DPU-AD1, D2, D3(samples of polyurethaneresin with ammonium dihydrogen phosphate aqueous solution) had good property. As known in the results, increase of ammonium dihydrogen phosphate constant did not influence to big change of polyurethane resin properties. As test of tensile strength, DPU had highest tensile characteristic($3.114kg_f/mm^2$) and DPU-AD3 had lowest tensile characteristic($2.510kg_f/mm^2$). As same as tensile characteristic, abrasion test determined DPU(50.5 mg.loss) had highest properties. In elongation case, DPU had best properties(602 %) in this experiment.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.3
• /
• pp.500-508
• /
• 2014

For this research, synthesis acrylic resin by ethyl acrylate monomer(EAM) and prepared samples which set by difference amount of monoammonium phosphate solution in waterborne acrylic resin. Use these resins, analyzed mechanical properties and thermal stability by films and leather surface coated. The test of DSC experiment sample WAC-APS3 was $410^{\circ}C$ Tm values which means the highest content of monoammonium phosphate had highest thermal stability in acrylic resin. According to measure data for solvent resistance, all samples showed good property. As known in the results, increase of ammonium phosphate constant did not influence to big change of resin properties. In abrasion test WAC-APS3 was good abrasion properties(68.729 mg.loss). Test of tensile strength, as increase as monoammonium phosphate resin analyzed low properties $1.505kgf/mm^2$ to $1.275kgf/mm^2$. In elongation case, same as strength test result 425 % to 384 % by increase to monoammonium phosphate amount in acrylic resin.

• Journal of Adhesion and Interface
• /
• v.22 no.4
• /
• pp.118-127
• /
• 2021

In this study, the mechanical properties of vulcanized rubber were evaluated through compounding by controlling filler content to improve the mechanical properties of NBR rubber. Aramid and glass fibers with excellent heat resistance were used as fillers, and ceramics were additionally used in anticipation of a complementary effect, and as for the ceramic materials, needle-shaped and plate-shaped ceramics were used. Each filler was used in an amount of 5.0, 10.0, 15.0, and 20.0 phr in order to investigate the basic properties according to the amount of filler. To confirm the complementary effect through ceramic application, each 10.0 phr fiber and ceramic were mixed with 1:1 ratio to evaluate mechanical properties. As a result, it was confirmed that the decreasing ratio of tensile strength after heat aging was small in the order of aramid fiber, acicular ceramic, glass fiber, and plate ceramic in the case of applying the filler alone. In addition, the mechanical characteristics of vulcanized rubber using composite filler based on fibers and ceramics were evaluated, and it was confirmed that the composite filler had a complementary effect on thermal aging.

• Clean Technology
• /
• v.15 no.3
• /
• pp.172-179
• /
• 2009

The thermoplastic polyurethane waste (TPU-S) with good tensile properties, hardness, NBS abrasion resistance, specific gravity and low wet coefficient of kinetic friction was melt-blended with ethylene propylene diene monomer rubber (EPDM) with high wet slip resistance and low mechanical properties to form EPDM/TPU-S blend films, and their composition-property relationship was investigated to find the optimum composition for shoe outsole material. The properties except the wet slip resistance increased with increasing TPU-S contents in the blend. All the properties except elongation at break, specific gravity and the wet coefficient of kinetic friction in the range of $0{\sim}65\;wt%$ of TPU-S did not attain the values predicted by the simple additive rule. The optimum weight ratio of EPDM/TPU-S for the application to the typical shoe outsole material was found to be 30/70.

• Analytical Science and Technology
• /
• v.22 no.5
• /
• pp.386-394
• /
• 2009

Formaldehyde is used in lether manufacture, a dry plate and an explosive. It is by-product of ozonizing process in filtration plant. The effects of exposure are eye pruritus, tickle, runing nose, blocking nasal passages and headache. It also makes a dried throat and causes inflammation. It is classified as B1 group for inhalation by US. EPA, which can cause cancer in human. For analysis of formaldehyde, formaldehydes-DNPH derivative was extracted with solid cartridge and was analyzed by High Performance Liquid Chromatography/Diode Array Detector (HPLC/DAD). The detection limit was $3{\mu}g/L$ and the recoveries were 72.3~109.1% (RSD 2.9~11.5%). Water samples were collected in four Korean rivers, four times per year seasonally for 10 years from 1998 to 2007. The monitoring results were 48.8% (630/1291), $5.15{\sim}101.9{\mu}g/L$ in purified water. Because of non-carcinogen in drinking water, hazard index is calculated with RfD. Results of excess cnacer risk was below 1 and was considered as safe value.

• Korean Journal of Soil Science and Fertilizer
• /
• v.37 no.5
• /
• pp.304-314
• /
• 2004

The objective of this study was to investigate the effect of organic materials (compost, straw, green manure, pig manure, seed production oil cake, and industrial by products including municipal sewage sludge, industrial sewage sludge, leather processing sludge, and alcohol fermentation processing sludge) on physical properties of soils in seven paddy and four upland fields with differential soil textures, sandy loam, loam, or clay loam, etc. The investigated physical parameters were bulk density (BD), air permeability (AP), macroporosity, hardness, shear resistance, frictional resistance, water stability aggregate (WSA), and Middleton's dispersion ratio. Except for coarse sandy loam field with weak structure, a decrease in BD and shear resistance, and an increase in macroporosity and AP in plots with applying organic materials compared to plots without applying organic materials appeared. In upland fields, the positive effect of organic materials on WSA, BD, and air permeability was higher than in paddy fields. The combined plot of NPK and compost had lower BD, hardness, and shear resistance, and higher macroporosity and WSA than plot with compost. Green manure had higher positive effect on physical properties of soils compared to other organic materials and the extent of positive effect had no significant correlation with soil organic matter content. Of industrial byproducts applied in coarse sandy loam soil under upland condition, municipal sewage sludge and pig manure compost had higher effect on increase of WSA than leather processing sludge and alcohol fermentation processing sludge. Unlike WSA, there were no significant differences between industrial byproduct types in other physical properties. in silty clay loam soil under the upland condition, straw had more positive effect on soil physical parameters than hairy vetch and pig manure. Therefore, different organic materials had differently active effect on physical parameters depending on types of soil and land use. Especially, it could be thought that well-decomposed organic materials have the advantage of an increase in organic matter content, while coarse organic materials of an increase in WSA.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.11 no.2
• /
• pp.135-144
• /
• 2001

This study was performed to measure airborne dimethylformamide(DMF), methyl ethyl ketone(MEK) and toluene and their urinary metabolites concentrations and to determine the relationship between airborne and urinary concentration. Airborne samples and their urinary metabolites were measured 98 male workers who work for 8 synthetic leather factories in a portion of Kyoung-In area. Urine samples were collected at end-of-shift to estimate the exposure levels. 1. The concentration of airborne DMF by process was 8.81 ppm for wet-mixing, 15.05 ppm for wet-coating, 6.03 ppm for dry-mixing, 5.58 ppm for dry-coating, 5.37 ppm for printing, and 9.03 ppm for total. There was statistically significant difference by process. Urinary NMF concentrations of wet-mixing, wet-coating, dry-mixing, dry-coating and printing were $90.55mg/{\ell}$, $79.80mg/{\ell}$, $39.86mg/{\ell}$, $25.23mg/{\ell}$, and $38.15mg/{\ell}$, respectively, and total geometric mean was $56.24mg/{\ell}$. There was significant difference by process. 2. The concentration of airborne MEK by process was 1.89 ppm for wet-mixing, 1.96 ppm for wet-coating, 10.33 ppm for dry-mixing, 29.24 ppm for dry-coating, 14.98 ppm for printing, and 4.87 ppm for total. There was statistically significant difference by process. Urinary MEK concentrations of wetmixing, wet-coating, dry-mixing, dry-coating and printing were $0.93mg/{\ell}$, $0.70mg/{\ell}$, $3.29mg/{\ell}$, $3.29mg/{\ell}$, and $1.06mg/{\ell}$, respectively, and total geometric mean was $1.25mg/{\ell}$. There was statistically significant difference by process. Urinary MEK 3. The concentration of airborne toluene by process was 0.35ppm for wet-mixing, 0.42ppm for wet-coating, 2.95ppm for dry-mixing, 11.67ppm for dry-coating, 4.88ppm for printing, 1.24ppm for total. There was statistically significant difference by process. Urinary hippuric acid concentrations of wet-mixing, wet-coating, dry-mixing, dry-coating and printing were 0.24g/g creatinine, 0.21g/g creatinine, 0.34g/g creatinine, 0.52g/g creatinine, and 0.29g/g creatinine, respctively and total geometric mean was 0.28g/g creatinine. There was statistically significant difference by process. 4. No. of exceeded KPEL was 40 workers(40.8%) for DMF(10ppm), 1 worker(1.0%) for MEK(200ppm), and no worker for toluene(100ppm). No. of exceeded KBEI was 62 workers(63.3%) for urinary NMF($40mg/{\ell}$), 29 workers(29.6%) for urinary MEK, 1 worker(1.0%) for urinary hippuric acid. 5. The regression equations were Log(NMF)=0.4094*Log(DMF)+1.3587(r=0.4516) for DMF, Log(MEKU)=0.1859*Log(MEK)-0.0324(r=0.3303) for MEK, Log(HA)=0.2106*Log(Toluene)-0.5685(r=0.4497) for toluene. Synthetic leather factory workers expose to 3 kinds of organic solvents which are DMF, MEK and toluene. Their urinary NMF and MEK levels were higher than their concentration levels through respiratory. It seems that the urinary levels were affected skin absorption for working habit and alcohol intake.

• Korean Journal of Environmental Agriculture
• /
• v.17 no.1
• /
• pp.48-53
• /
• 1998

The purpose of this study was to compare heavy metal concentrations in uncontaminated soil with those in soil influenced by industrial activities, and to investigate the relationship between change of heavy metal content and the kind of industry at the Iksan 1st Industrial Complex that has started since 1975. Soils sampled in 0-3㎝ and 3-6㎝ soil depth, respectively were analized for content of Cd, Cu, Ni, Pb and Zn. Change of heavy metal content in soil of the industrial complex were more accumulated 16 to 25% of Cd and Cu, 93% of Pb and Zn, respectively in samples compared with natural soil uncontaminated. But there was no different in Ni content between two soil. Distribution of Cd in soil layer of 0 to 3cm was the highest concentration of 5 ppm more at the textile industries, and then higher at the chemicals and the food processing industries. In 3 to 6㎝ soil layer Cd content was the highest concentration of 5 ppm more at the metal processing industries, and then higher at the textile industries. Cd accumulation in soil was different according to a kind of industry and soil depth. Cu content was the highest value of 400 ppm more in soil layer of 0 to 3cm at the manufacturing electric wires industry area and showed the accumulation phenomenon in soil layer 3 to 6cm at the ohmmeter, machines and electric wires industry area. Ni content was 35 ppm more in soil of the metal plating and processing industries regardless of soil sampling layer. Then it was 25 ppm more in soil of the building stones and semiconductor industries. Pb content was from 400 to 1000 ppm in soil of the chemicals and textiles industries regardless of soil sampling layer. Zn content was 1200 ppm more in soil of the chemicals and silk fabrics industries regardless of soil depth, and then lower in order to soil of leather processing${\le}$metal plating industries. In conclusion, changes of heavy metal kinds and content in soil of this industrial complex area were caused by the type or kinds of industrial activities. Changes of Pb and Zn content in soil were dominated at this area.