• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.3
• /
• pp.94-104
• /
• 1994

In order to improve engine performance and its reliability it is very important to find the friction force between piston-ring assembly and cylinder wall in engine operating conditions. A new system was developed for the piston-ring assembly friction force measurement. This system had a relatively high fundamental frequency at 884 Hz and a fine resolution of 0.5N in friction force measurement. Comparing with existing floating liner systems this systems required small installation space and at the same time alleviated the system noise problem induced by the thrust and slap impulse forces.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.6
• /
• pp.1510-1519
• /
• 1994

It is important to understand the friction characteristics between piston-ring assembly and cylinder wall for the friction loss reduction as well as the solution of problem such as scuffing wear and oil consumption. A new system was developed for the piston-ring assembly friction force measurement. This system was applied to the friction force measurement to find its functional relationship with variables such as engine speed, oil viscosity, and engine load. The friction mean effective pressure(fmep) was found to have a linear relationship with$(\vpsilon{U})^{0.42}$ under motering and with$(\vpsilon{U})^{0.45}$ under firing operations, where $\vpsilon$ is the kinematic oil viscosity and U is mean piston speed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.2
• /
• pp.28-34
• /
• 2014

A non-contact type measurement system is specially devised to measure the width of a piston ring groove in the grinding process. This system comprises a line camera with an imaging lens, collimated white light source, and a one axis translation stage. When the measurement system movesalong the diagonal direction of the cylinder, the line camera captures an image. By analyzing such images, the width of the piston ring groove can be determined. The experimental results prove that the proposed system is useful, especially as a monitoring system in grinding piston ring grooves on cylinders with accuracy of several micrometers in an area of dozens of millimeters.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.114-120
• /
• 2000

Friction forces of piston rings for a typical SI engine were independently measured while excluding the effects of cylinder pressure, oil starvation and piston secondary motion using a floating liner system. Friction patterns, represented by the measured friction forces, were classified into five frictional modes with regard to the combination of predominant lubrication regimes(boundary, mixed and hydrodynamic lubrication) and stroke regions(mid-stroke and dead centers). The modes were identified on the Stribeck diagram of the dimensionless bearing parameter and friction coefficients which were evaluated at the mid-stroke and at the dead centers. And the frictional modes were estimated to the full operation range. The compression rings behave in the mode where hydrodynamic lubrication is dominant at the mid-stroke and mixed lubrication is dominant at the dead centers under steady operating conditions. However, the oil control ring behave in the mode where mixed lubrication is dominant throughout the entire stroke.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.56-64
• /
• 2000

A friction force measurement system using the floating liner method was developed to study the frictional behavior of piston rings. The measurement system was carefully designed to control the effect of the piston secondary motion and the temperature of cylinder wall and oil. The friction force between the barrel shaped piston ring and the cylinder liner, was measured under the condition of flooded oil supply. The measured friction forces were classified into five frictional modes with regard to the combination of predominant lubrication regimes(boundary, mixed and hydrodynamic lubrication) and stroke regions(midstroke and dead centers). The modes could be identified on the Stribeck diagram of the friction coefficients and the dimensionless number of ㎼/p, where the friction coefficients are evaluated at near the midstroke and dead centers.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.8
• /
• pp.1608-1614
• /
• 2002

This Paper presents a novel piston friction force measurement system that has characteristics of relieving the Pressure force acting on the upper surface of the liner; the system uses general rubber O-rings for combustion chamber sealing, and does not need special changes to the piston top land. The lower supporter of the floating liner increases stiffness in liner axial direction, and results in the increase of natural frequency. The upper supporter has multi-layer structure designed fer low axial stiffness and high radial stiffness. With the use of the present system, the effects of variation in clearance and piston ring tension were studied.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.299-299
• /
• 2014

엔진블럭 사이를 왕복 운동하는 피스톤은 엔진블럭과의 마찰은 불가피한 상태일 수밖에 없으며 이렇게 된다면 엔진블럭 또는 피스톤의 파손, 변경이 있을 수밖에 없다. 피스톤에 대한 연구는 이러한 파손, 변경을 최소화시키기 위해서 내마모성, 내열성 그리고 내구성을 향상시키는데 목적을 두고 있다. 본 실험은 APS법으로 제작된 자기윤활복합코팅층을 준비해 레이저표면텍스처링을 넣어 마찰 실험을 하였다. 기지재로는 알루미나-지르코니아복합체를 사용하였고, 고체윤활제로는 $CaF_2$ 및 $BaF_2$을 사용하였다.

• Tribology and Lubricants
• /
• v.23 no.5
• /
• pp.201-206
• /
• 2007

The bent-axis type piston pump which is driven by the piston rod works on the way that the piston rod drives the cylinder block, so the taper angle of the piston rod and the swivel angle between the cylinder block and the shaft are very important design factors. If the above factors cannot satisfy the conditions of optimum design, the friction loss between the cylinder bore and the piston increases, and the pump can even fail to work under conditions of severe friction and wear. Since the piston reciprocates in the cylinder bore with high velocity, and at the same time it rotates on its own axis and revolves on the center of the cylinder block, the decrease of the volume efficiency generated on account of the leakage between the cylinder bore and the piston. Therefore, to prevent this case, the piston ring is designed at the end of the piston, and the friction characteristics between the piston ring and the cylinder bore are in need of research due to its great influence on the performance of piston pump. Thus, in this paper, the elastic hydraulic oil's lubrication analyses of the film thickness, the pressure distribution, and the friction force, and so on, have been performed, and the lubrication characteristics between the piston ring and the cylinder bore are explored by the results of the numerical analysis, and it is contributed to realize the higher efficiency and the more advanced performance of the bent-axis type piston pump.

• Journal of Korea Foundry Society
• /
• v.24 no.3
• /
• pp.132-137
• /
• 2004

• Journal of Korea Ship Safrty Technology Authority
• /
• v.16
• /
• pp.90-96
• /
• 2004

연료내의 오염물질은 고체오염물질과 액체오염물질로 나눌 수 있다. 고체 오염물질은 피스톤링과 실린더 라이더의 과도한 마모를 유발하거나 연료분사 펌프와 연료 분사 밸브의 고착을 일으킬 수 있다.