• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.9
• /
• pp.7-13
• /
• 2009

This paper presents a multi-channel transceiver that achieves a data rate of 3.125Gb/s/ch. The LVDS is used because of its noise immunity and low power consumption. And a pre-emphasis circuit is also proposed to increase the transmitter speed. On the receiver side, a low-power CDR(clock and data recovery) using 1/4-rate clock based on dual-interpolator is proposed. The CDR generates needed additional clocks in each recovery part internally using only inverters. Therefore each part can be supplied with the same number of 1/4-rate clocks from a clock generator as in 1/2-rate clock method. Thus, the reduction of a clock frequency relaxes the speed limitation and lowers power dissipation. The prototype chip is comprised of two channels and was fabricated in a $0.18{\mu}m$ standard CMOS process. The output jitter of transmitter is loops, peak-to-peak(0.31UI) and the measured recovered clock jitter is 47.33ps, peak-to-peak which is equivalent to 3.7% of a clock period. The area of the chip is $3.5mm^2$ and the power consumption is about 119mW/ch.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.2 s.332
• /
• pp.73-82
• /
• 2005

Test data volume and power consumption for scan vectors are two major problems in system-on-a-chip testing. Therefore, this paper proposes a new test data compression/decompression method for low power testing. The method is based on analyzing the factors that influence test parameters: compression ratio, power reduction and hardware overhead. To improve the compression ratio and the power reduction ratio, the proposed method is based on Modified Statistical Coding (MSC), Input Reduction (IR) scheme and the algorithms of reordering scan flip-flops and reordering test pattern sequence in a preprocessing step. Unlike previous approaches using the CSR architecture, the proposed method is to compress original test data, not $T_{diff}$, and decompress the compressed test data without the CSR architecture. Therefore, the proposed method leads to better compression ratio with lower hardware overhead and lower power consumption than previous works. An experimental comparison on ISCAS '89 benchmark circuits validates the proposed method.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.4
• /
• pp.60-70
• /
• 2000

An 8$\times$8+20-bit MAC is designed with low power design methodologies at each of the system design levels. At algorithm level, a new method for multipl $y_tract operation is proposed, and it saves the transistor counts over conventional methods in hardware realization. A new Booth selector circuit using NMOS pass-transistor logic is also proposed at circuit level. It is superior to other circuits designed by CMOS in power-delay-product. And at architecture level, we adopted an ELM adder that is known to be the most efficient in power consumption, operating frequency, area and design regularity as the final adder. For registers, dynamic CMOS single-edge triggered flip-flops are used because they need less transistors per bit. To increase the operating frequency 2-stage pipeline architecture is adopted, and fast 4：2 compressors are applied in Wallace tree block. As a simulation result, the designed MAC in 0.6${\mu}{\textrm}{m}$ 1-poly 3-metal CMOS process is operated at 200MHz, 3.3V and consumed 35㎽ of power in multiply operation, and operated at 100MHz consuming 29㎽ in MAC operations, respectively.ly.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.1
• /
• pp.75-82
• /
• 2000

In this paper, a new low power 16-bit ALU has been designed, fabricated and tested at the transistor level. The designed ALU performs 16 instructions and has a two-stage pipelined architecture. For the reduction of switched capacitance, the ELM adder of the proposed ALU is inactive while the logical operation is performed and P(propagation) block has a dual bus architecture. A new efficient P and G(generation) blocks are also proposed for the above ALU architecture. ELM adder, double-edge triggered register and the combination of logic style are used for low power consumption as well. As a result of simulations, the proposed architecture shows better power efficient than conventional architecture$^{[1,2]}$ as the number of logic operation to be performed is increased over that of arithmetic to logic operation to be performed is 7 to 3, compared to conventional architecture. The proposed ALU was fabricated with 0.6${\mu}m$ single-poly triple-metal CMOS process. As a result of chip test, the maximum operating frequency is 53MHz and power consumption is 33mW at 50MHz, 3.3V.

• The KIPS Transactions:PartA
• /
• v.11A no.2
• /
• pp.195-202
• /
• 2004

This paper introduces the design or parallel Pipeline high-speed analog-to-digital converter(ADC) for the high-resolution video applications which require very precise sampling. The overall architecture of the ADC consists of 4-channel parallel time-interleaved 10-bit pipeline ADC structure a]lowing 200MSample/s sampling speed which corresponds to 4-times improvement in sampling speed per channel. Key building blocks are composed of the front-end sample-and-hold amplifier(SHA), the dynamic comparator and the 2-stage full differential operational amplifier. The 1-bit DAC, comparator and gain-2 amplifier are used internally in each stage and they were integrated into single switched capacitor architecture allowing high speed operation as well as low power consumption. In this work, the gain of operational amplifier was enhanced significantly using negative resistance element. In the ADC, a delay line Is designed for each stage using D-flip flops to align the bit signals and minimize the timing error in the conversion. The converter has the power dissipation of 280㎽ at 3.3V power supply. Measured performance includes DNL and INL of +0.7/-0.6LSB, +0.9/-0.3LSB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.4A
• /
• pp.336-344
• /
• 2005

Discrete Wavelet Transform(DWT) is the oncoming generation of compression technique that has been selected for MPEG4 and JEPG2000, because it has no blocking effects and efficiently determines frequency property of temporary time. In this paper, we propose an efficient bit-serial architecture for the low-power and low-complexity DWT filter, employing two-channel QMF(Qudracture Mirror Filter) PR(Perfect Reconstruction) lattice filter. The filter consists of four lattices(filter length=8) and we determine the quantization bit for the coefficients by the fixed-length PSNR(peak-signal-to-noise ratio) analysis and propose the architecture of the bit-serial multiplier with the fixed coefficient. The CSD encoding for the coefficients is adopted to minimize the number of non-zero bits, thus reduces the hardware complexity. The proposed folded 1D DWT architecture processes the other resolution levels during idle periods by decimations and its efficient scheduling is proposed. The proposed architecture requires only flip-flops and full-adders. The proposed architecture has been designed and verified by VerilogHDL and synthesized by Synopsys Design Compiler with a Hynix 0.35$\mu$m STD cell library. The maximum operating frequency is 200MHz and the throughput is 175Mbps with 16 clock latencies.

• The KIPS Transactions:PartA
• /
• v.10A no.3
• /
• pp.247-254
• /
• 2003

This paper describes a Delay Locked Loop (DLL) with low supply voltage and wide lock range for Synchronous DRAM which employs Double Data Rate (DDR) technique for faster data transmission. To obtain high resolution and fast lock-on time, a new type of phase detector is designed. The new counter and lock indicator structure are suggested based on the Dual-clock dual-data Flip Flop (DCDD FF). The DCDD FF reduces the size of counter and lock indicator by about 70%. The delay line is composed of coarse and fine units. By the use of fast phase detector, the coarse delay line can detect minute phase difference of 0.2 nsec and below. Aided further by the new type of 3-step vernier fine delay line, this DLL circuit achieves unprecedented timing resolution of 25psec. This DLL spans wide locking range from 500MHz to 500MHz and generates high-speed clocks with fast lock-on time of less than 5 clocks. When designed using 0.25 um CMOS technology with 1.8V supply voltage, the circuit consumes 32mA at 500MHz locked condition. This circuit can be also used for other applications as well, such as synchronization of high frequency communication systems.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.10 no.4
• /
• pp.81-93
• /
• 2000

In a methodological approach to improve the processing performance of modulo exponentiation which is the primary arithmetic in RSA crypto algorithm, we present a new RSA hardware architecture based on high-radix modulo multiplication and CRT(Chinese Remainder Theorem). By implementing the modulo multiplier using radix-16 arithmetic, we reduced the number of PE(Processing Element)s by quarter comparing to the binary arithmetic scheme. This leads to having the number of clock cycles and the delay of pipelining flip-flops be reduced by quarter respectively. Because the receiver knows p and q, factors of N, it is possible to apply the CRT to the decryption process. To use CRT, we made two s/2-bit multipliers operating in parallel at decryption, which accomplished 4 times faster performance than when not using the CRT. In encryption phase, the two s/2-bit multipliers can be connected to make a s-bit linear multiplier for the s-bit arithmetic operation. We limited the encryption exponent size up to 17-bit to maintain high speed, We implemented a linear array modulo multiplier by projecting horizontally the DG of Montgomery algorithm. The H/W proposed here performs encryption with 15Mbps bit-rate and decryption with 1.22Mbps, when estimated with reference to Samsung 0.5um CMOS Standard Cell Library, which is the fastest among the publications at present.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.7
• /
• pp.1071-1077
• /
• 2022

A security SoC that can be used to implement elliptic curve cryptography (ECC) based public-key infrastructures was designed. The security SoC has an architecture in which a hardware accelerator for the elliptic curve digital signature algorithm (ECDSA) is interfaced with the Cortex-A53 CPU using the AXI4-Lite bus. The ECDSA hardware accelerator, which consists of a high-performance ECC processor, a SHA3 hash core, a true random number generator (TRNG), a modular multiplier, BRAM, and control FSM, was designed to perform the high-performance computation of ECDSA signature generation and signature verification with minimal CPU control. The security SoC was implemented in the Zynq UltraScale+ MPSoC device to perform hardware-software co-verification, and it was evaluated that the ECDSA signature generation or signature verification can be achieved about 1,000 times per second at a clock frequency of 150 MHz. The ECDSA hardware accelerator was implemented using hardware resources of 74,630 LUTs, 23,356 flip-flops, 32kb BRAM, and 36 DSP blocks.

• Journal of Life Science
• /
• v.25 no.4
• /
• pp.416-424
• /
• 2015

Pinosylvin is a stilbenoid found in the Pinus species. Pinosylvin at ~pM to ~nM concentrations induces cell proliferation, cell migration and anti-inflammatory activity in endothelial cells. However, it was recently reported that pinosylvin at high concentrations (50 to 100 μM) induces cell death in bovine aortic endothelial cells. In this study, we conducted a series of experiments to discover how pinosylvin at a high concentration (50 μM) induces endothelial cell death. Pinosylvin at the high concentration was shown to induce endothelial cell apoptosis through enhancing caspase-3 activity, flip-flop of phosphatidyl serine, and nuclear fragmentation. We found that pinosylvin at the high concentration additively increased caspase-3 activity enhanced by serum-starvation or treatment with 100 μM etoposide. We also determined that pinosylvin at the high concentration promoted activations of c-Jun N-terminal kinase (JNK) and endothelial nitric oxide synthetase (eNOS). We further ran a series of experiments to find out which signaling molecule plays a critical role in the pinosylvin-induced apoptosis. We finally found that SP-600125, a JNK inhibitor, had an inhibitory effect on the pinosylvin-induced endothelial cell death, but L-NAME, an eNOS inhibitor, had no effect. These data indicate that JNK is involved in the pinosylvin-induced apoptosis. Collectively, pinosylvin at high doses induces cell apoptosis via JNK activation.