• Journal of Korean Society of Steel Construction
• /
• v.23 no.3
• /
• pp.275-282
• /
• 2011

A recent development of seismic design, which is required among environmentally friendly members, increased the concern on light-weight concrete. Extending around the building, the structural design which is applied for light-weight concrete has been increased. This study therefore evaluates the bending resistance and the shear resistance involved using four specimens that were manufactured and tested. The parameters used in this study exist. This study investigates the structural performance of composite slab using light-weight concrete with KCI (2007).

• Composites Research
• /
• v.29 no.5
• /
• pp.231-235
• /
• 2016

In this study, integrated co-bonded panels with the same configuration of hat stiffeners were fabricated and measured for ply waviness phenomenon. Total specimens consisted of 2 types; 1) the general co-bonded panel and 2) the co-bonded panel with caul plate made of carbon epoxy composite materials. The first general co-bonded panel specimen exhibited that laminate thickness on the stiffener location area was much thicker than the non-stiffener area and, there was ply waviness with 0.61 mm height and 3.29 mm length. In the second co-bonded panel specimen, the reduced waviness with 0.22 mm height and 1.37 length resulted in more than 50% improvements, which is due to the uniform pressure distribution of co-bonded interface by caul plate.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.3
• /
• pp.231-237
• /
• 2007

The torque ripple of the hydraulic pumps for the Electro-hydrostatic Actuators can disturb the cylinder position control under slewing speed operation condition. In principle, the periodic change of the reaction torque generated by a piston type pump is highly dependent on the waveform of its cylinder chamber pressure. In case of uni-directional pumps operating at constant speed, the transient overshoot and rising slope of the cylinder pressure can be adjusted by the precompression angle and notch shape of their valve plates. Therefore, the influence of the valve plate geometry on the torque ripple magnitude of a bent-axis type piston pump for EHA application was investigated in this study. The results showed that any improvement of the torque ripple of such a bi-directional pump can not be achieved by modifying the valve plate geometry, regardless of its operation speed.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.5
• /
• pp.543-551
• /
• 2015

In this paper, Used on the bridge and ship, investigate the physical relationship of aluminium plate girders(A6082-T6) considering the marine environment. Plate girder will experience the patch loading such as moving load, surcharge in the product life cycle. The ultimate strength of aluminum plate girders subjected to these loads applied multiple numerical model and performed the elasto-plastic large deflection series analysis and was proposed the predicted formula for regression analysis. The predicted formula was shown by the relationship of ultimate strength and slenderness. If the slenderness is low(0-2.3), it causes a 9 % error, and If the slenderness is higher(2.3-4.0), it causes a 1-2 % error. Therefore, the propriety of proposed prediction formular was found to be assess rationally.

• Journal of Korean Society of Steel Construction
• /
• v.29 no.4
• /
• pp.269-280
• /
• 2017

In this study, seismic performance was evaluated for the exposed column-base plate weak-axis connections of small size steel structures through cyclic loading tests. The primary test parameters are the thickness of base plate, the presence of rib plates, the number of anchor bolts and embedment length of anchor bolts. To investigate the effect of bond performance of anchor bolts on the seismic performance of column-base plate connections, L-shaped round bars and thread bars were used as the hooked anchor bolts in the test specimens. Test results showed that bond performance of anchor bolts and the thickness of base plate significantly affect the structural performance and energy dissipation capacity. In particular, it was found that even if the requirements for minimum thickness of the base plate that is satisfied, the base plate can yield before the capacity of steel column reaches the plastic moment resulting in decreasing the structural performance of the connections. However, the proposed details of the connections might be considered as the partially restrained, that is semi-rigid connections. Consequently, the L-shaped thread anchor bolts is applicable in the exposed column-base plate weak-axis connections of small-size steel structures.

• Proceedings of the KIPE Conference
• /
• 2018.07a
• /
• pp.440-441
• /
• 2018

본 연구에서는 핫플레이트를 균일한 표면 온도로 가열시키기 위한 카트리지 히터의 설계를 시도하였다. 이를 위하여 1. 표면 전력밀도 및 전열선 전력밀도에 따른 발열온도 측정 실험 2. 카트리지 히터의 분할 영역과 전열선 권선 비율에 따른 온도 측정 실험을 실시하여 온도분포형 카트리지 히터의 설계 사양을 선정하였다. 또한 이렇게 설계한 카트리지 히터를 직접 제작하여 기존의 표준형 카트리지 히터와의 성능 비교 측정 실험을 실시하여, 본 연구에서 제시한 방법으로 제작한 카트리지 히터의 표면 온도 균일도가 우수함(표면 온도차 ${\leq}1.25[^{\circ}C]$)을 증명하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.107-107
• /
• 2004

현재 자동차관련 산업 및 기계 산업에 이용되고 있는 기존의 Forming type의 컨베이어 시스템은 인장력에 의해 hinge belt plate가 늘어지는 현상이 발생하고 이 현상에 의하여 소음 기계의 마모 등의 고장의 원인이 되어왔다. 이에 이러한 현상을 줄이기 위해 H/B의 소재 두께를 높이므로 강성은 증가하는 반면에, 단위중량이 무거워지는 단점이 있으며, 또한 제품을 성형하는 금형의 강도와 수명 및 크기가 한정되어 있어 수요자의 다양한 요구에 부응하기 어렵다.(중략)

• Proceedings of the SAREK Conference
• /
• 2003.07a
• /
• pp.133-133
• /
• 2003

• Journal of Korean Association for Spatial Structures
• /
• v.6 no.3 s.21
• /
• pp.123-130
• /
• 2006

This study propose cutting body portion-high strength mechanical fasteners to improve deformation capacity of High strength bolts, which are the mechanical fasteners used for End-plate connections. And, we report that loading test results of steel beam-to-column connection using high deformation capacity-high strength bolts in accordance with SAC2000 loading program. As a result, the initial stiffness and the maximum strength of the connection using high deformation capacity-high strength bolts, are approximately the same in comparison with those of the end-plate connection using the existing high strength bolts. But the deformation capacity of the connection is more than twice as much as those.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.4
• /
• pp.923-928
• /
• 2010

Anodic aluminum oxide (AAO) nanotemplates for nano electronic device applications have been attracting increasing interest because of ease of fabrication, low cost process, and possible fabrication in large area. The size and density of the nanostructured materials can be controlled by changing the pore diameter and the pole density of AAO nanotemplate. In this paper, nano porous alumina films AAO nanotemplate was fabricated by second anodization method using sputterd Al films. In addition, effects of electrolyte temperature and anodization voltate on the microstructure of porous alumina films were investigated. As the electrolyte temperature was increased from $8^{\circ}C$ to $20^{\circ}C$, the growth rate of nanoporous alumina films was increased from 86.2 nm/min to 179.5 nm/min. The AAO nanotemplate fabricated with optimal condition had the mean pore diameter of 70 nm and the pore depth of $1\;{\mu}m$.