• 대한기계학회논문집A
• /
• 제36권10호
• /
• pp.1155-1162
• /
• 2012

알루미늄 크래쉬 박스는 저속충돌조건에서 프론트 사이드 멤버를 변형을 방지하기 위한 부품이다. 본 연구에서는 저속충돌조건에서 비드형상이 알루미늄 크래쉬 박스의 충돌성능에 미치는 영향을 분석하였다. Edge concave, surface convex 와 surface concave 타입의 비드형상들에 대한 충돌해석 및 실험을 수행하여 비드가 없는 normal 타입의 알루미늄 크래쉬 박스의 충돌성능과 비교분석하였다. 충돌성능은 저속충돌조건에서 크래쉬 박스의 초기 최대하중 및 충돌에너지 흡수능으로 평가하였다. 이를 검증하기 위해 알루미늄 크래쉬 박스와 결합된 프론트 사이드 멤버에 대해 저속충돌실험 수행하고, 이를 분석하였다. Surface concave 타입의 비드가 삽입된 알루미늄 크래쉬 박스 경우, 프론트 사이드 멤버의 변형을 방지할 수 있음을 확인하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.178-182
• /
• 2008

Automotive manufacturers lay their eyes on the new manufacturing technologies because of the strengthened competition. Among them, a simultaneous forming is one of the innovative forming technologies to be able to reduce production time and cost. Several parts can be simultaneous manufactured by process, while the conventional stamping demands the same number of die sets with the number of parts. In this study, the automotive front side member was manufactured by the simultaneous forming. The position and the size of initial blank were determined by forming analysis and try-outs, and the blank movement during the forming was controlled by introducing the pilot pin.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.52-59
• /
• 2014

Front impacted SUV vehicle shows that the front parts of side members are collapsed by the bending due to the transverse load exerted at the end of side members. Side member models were impacted with various angles in order to study the crash performance according to the impact angle. Even for the small impact angle of $10^{\circ}$, crash performance seriously deteriorated and the deformations for impact angle $15^{\circ}$ were similar to those from the front body impact analysis. In addition, the angled front impact analysis for the straight member with hat section was carried out and the effects of inner reinforcement shape on crash performance was investigated.

• 한국기계기술학회지
• /
• 제13권1호
• /
• pp.105-112
• /
• 2011

Increasing needs for light weight and high safety in modern automobiles induced the wide application of high strength steels in automotive body structures- The main difficulty in the forming of sheet metal parts with high strength steel is the large amount of springback including sidewall curl and twist in channel shaped member parts- Among these shape defects, twist occurs frequently and requires numerous reworks on the dies to compensate the shape deviation- But until now, it seems to be no effective method to reduce the twist in the forming processes- In this study, a new forming process to reduce the twist deformation during the forming of automotive structural member was suggested- This method consists of forming and restriking of embosses on the sidewall around the stretch flanging area of the part- and was applied in the forming process design of an automotive front side inner member with high strength steel- To evaluate the effectiveness of the method, springback analysis using $Pamstampa^{tm}$ was done- Through the analysis results, the suggested method was proven to be effective in twist reduction of channel shaped parts with stretch flanging area.

• 한국자동차공학회논문집
• /
• 제21권5호
• /
• pp.97-103
• /
• 2013

Crash performance of the straight member was studied by FE analysis. One end of model was fixed and the other end was impacted by 1,000kg rigid mass with velocity of 16.0m/sec. The maximum and mean load were discussed to compare crash performance. The members with various section shapes were analyzed and the flange location was changed. Also, spot weld points were added in the initial buckling region to investigate its effect. Final rectangular section model which has flanges at the center and reinforcement in initial buckling region showed high enhancement in crash performance.