• Proceedings of the KSEG Conference
• /
• 2005.04a
• /
• pp.101-106
• /
• 2005

The three-dimensional Tomography developed by Kim and Bae(2004) was applied to 64,024 P and 64,618 S wave arrival times observed at 238 seismic stations for 4050 local earthquakes in the depth range from 0 to 300 km in and around Hokkaido, Japan. High and low velocity zones for Vp/Vs were clearly imaged in and around Hokkaido. The upper seismic planes of the double seismic zone (DSZ) were found in the subducted Pacific Plate beneath Hokkaido at depth of 40- 80 km, which produced high seismicity around Hokkaido. The findings of high Vp/Vs anomalies beneath the Moho discontinuity supports an evidence of a surface triple-collision hypothesis prepared by Moriya(1994) that the Kuril Arc(Okhotsk Plate or North American Plate) is colliding against the NE Japanese Arc(Amurian Plate or Eurasian Plate), along and beneath the Hidaka Mountain Range, and at the same time the Pacific Plate is subducting into these two plates, making an equilibrium of tectonic forces along the Hikada Mountain Range (HMR) corner and the central tectonic axis(142 ~ 143E) in Hokkaido. The low Vp and Vs were also found in east and west along the central tectonic axis in which the focal mechanism represents the extensional forces. These phenomena are also consistent with low Bouguer gravity anomalies in this region. It is understood why most of great earthquakes occurred outside Hokkaido where the balance of tectonic forces are breaking from the triple junction of three tectonic forces in Hokkaido.

• Journal of Soil and Groundwater Environment
• /
• v.14 no.6
• /
• pp.87-94
• /
• 2009

Surfactant-enhanced air sparging (SEAS) was developed to suppress the surface tension of groundwater prior to air sparging resulting in higher air saturation and larger contact area between NAPL and gas during air sparging. Larger contacting interface between NAPL and gas means faster mass transfer of contaminants from NAPL to gas phase. This new technique, however, is limited to relatively volatile contaminants because vaporization is its basic mechanism of mass transfer. In this study, SEAS was tested at an elevated temperature for a semi-volatile n-decane, which is expected not to be a good candidate of SEAS application due to its low vapor pressure at ambient temperature. Three sparging experiments were conducted using 1-dimensional column (5 cm id, 80 cm length) packed with sand; (1) ambient temperature ($23^{\circ}C$), column saturated with distilled water, (2) SEAS at ambient temperature ($23^{\circ}C$), for n-decane contaminated sand, (3) SEAS at elevated temperature ($73^{\circ}C$), for n-decane contaminated sand. Higher air saturation was achieved by SEAS compared to that by air sparging without surfactant application. The n-decane removal efficiency of SEAS at elevated temperature was significantly higher(> 10 times) than that of ambient SEAS. The n-decane concentrations in the gas effluent from column during SEAS at $73^{\circ}C$ are found to be 10 times of those measured at ambient temperature. Thus, SEAS technique can be applied for removal of semi-volatile contaminants provided that an appropriate technique for elevating aquifer temperature is available.

• Journal of Sericultural and Entomological Science
• /
• v.30 no.1
• /
• pp.33-39
• /
• 1988

In the case of white cocoon, the fluorescence colors are classified as a yellowish fluorescence cocoon(Y.F.C.) and a violet fluorescence cocoon(V.F.C.) by exposing to ultra-violet ray. Accordingly, experiments were carried out to investigate the difference of sericin behaviors between Y.F.C. and V.F.C. by measuring the sericin solubility, surface tension and viscosity of the sericin solution. Also, the reelability of two different type of cocoons was investigated in the silk reeling process. The results were summarized as follows; 1. The sericin solubility of Y.F.C. shell is higher than that of V.F.C. shell with the dissolution temperature and time. It is shown that the sericin solubility curves of Y.F.c. and V.F.C. are similar in shape, but the difference of sericin solubility between Y.F.C. and V.F.C. is more significant at higher bath temperature. 2. The initial sericin dissolution curves of Y.F.C. and V.F.C. cocoon shell can be divided by four parts within the range of dissolving time from 5 minutes to 60 minutes. The initial dissolution velocity of Y.F.C. shell is faster than that of V.F.C. but the velocity difference is negligible after 30 minutes of dissolving time. 3. The gelation of V.F.C. sericin solution is faster than that of Y.F.C. at early stage(in the range of 15 minutes to 60 minutes). 4. In the silk reeling process, the reelability of Y.F.C. is better than that of V.F.C. with about 11%. This is mainly due to the higher sericin solubility in Y.F.C. followed by the fast dissolution velocity.

• The Korean Journal of Pesticide Science
• /
• v.8 no.4
• /
• pp.325-331
• /
• 2004

The studies were undertaken to establish optimum formulation recipes of acetamipid 4% SL(soluble concentrate) using different adjuvants and to evaluate enhanced control effect on target insect pests by adjuvants. Adjuvants for the studies used were SS(Sodium alkylcarboxylate) and PE(Polyoxyethylene alkyl ether). After the fundamental recipe for SL being established by using co-solvent for stability at low temperature, four types of SL were formulated. The physical properties and insecticidal efficacies of the tested SL formulations were investigated. Surface tension of SL1 without adjuvant was highly decreased from 44 dyne/cm to 34 dyne/cm by addition of adjuvants. SL4 using mixed adjuvant showed the lowest contact angle. Efficacies of SL1 without adjuvant against the palm thrips (Thrips palmi) and the cotton aphid (Aphis gossypii) on cucumber were increased by adding adjuvants. SL4 using mixed adjuvant showed higher efficacy than SL2 and SL3 using single adjuvant. These results have demonstrated that the selected adjuvants could be used to enhance insecticide efficacy and reduce spray dose of insecticide.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.9
• /
• pp.763-771
• /
• 2014

As a preliminary study on the spray behavior characteristics of emulsified fuel, the fuel properties (viscosity, surface tension, and density) and evaporation characteristics of a fuel droplet were investigated. The emulsified fuel was made by mixing diesel and $H_2O_2$. In addition, the macroscopic spray behavior characteristics such as the spray penetrations and spray angles of the emulsified and diesel fuels were compared. The stirring condition of the emulsified fuel was a 9:1 mixture of the diesel fuel and the surfactant span 80. The mixing ratios for the hydrogen peroxide were set at EF2, EF12, EF22, EF32, EF42, EF52, EF62, EF72, EF82, and EF92. The injection pressures were set at 400, 600, 800, and 1000 bar. We found that as the mixing ratio of the hydrogen peroxide was increased from EF2 to EF52, the viscosity of the emulsified fuel increased. However, afterward, the viscosity of the emulsified fuel gradually decreased and approached the viscosity value of the diesel fuel. Therefore, generally oil-in-water emulsions were used for the hydrogen peroxide mixing ratios up to 52 (EF52), and water-in-oil emulsions were used for the hydrogen peroxide mixing ratios above 52. Finally, the spray behavior characteristics (spray penetration and spray angle) of the emulsified fuel were found to be almost independent of the mixing ratio.

• Applied Chemistry for Engineering
• /
• v.9 no.4
• /
• pp.565-568
• /
• 1998

Amphipathic compounds (bis-sulfonate Gemini type) with double or triple long chain alkyl groups were prepared by the reaction of N-(long chain acyl)diethanolamine diglycidyl ethers with fatty alcohols, followed by the reaction with propanesultone. All these new Gemini type surfactants were soluble in water and showed much better micelle forming ability and lowering surface tension than sodium dodecyl sulfonate with one sulfonate group. cmc and ${\Upsilon}$ cmc values of the triple-chain compounds were still much smaller than those of the corresponding double-chain compounds with two common alkyl groups. The efficiency of adsorption at the water/air interface ($pC_{20}$) of these surfactants was very high. Their foaming properties, wetting ability toward a felt chip, and lime-soap dispersing requirement (LSDR) were measured. Their initial foaming properties were high but showed good low foam stability, wettability and LSDR.

• Journal of Marine Bioscience and Biotechnology
• /
• v.1 no.4
• /
• pp.268-274
• /
• 2006

Bacillus sp. DYL130 producing biosurfactant was isolated from soil samples in the Duck-yu mountain and identified as Bacillus sp. by analysis of 16S rDNA sequence. Purification of the biosurfactant was performed by using affinity chromatography and TLC. The biosurfactant of culture medium from Bacillus sp. DYL130 was eluted with 100% methanol using affinity chromatography. To remove methanol, a rotary evaporator was used and enrichment sample was dissolved in alkaline water(pH 10). The purified biosurfactant was identified by TLC. It was confirmed that the Rf value of the biosurfactant was 0.78. Antifungal activity against Botrytis cineria was showed the strongly activity as active antagonist. Maximum emulsification activity and stability were obtained from soybean oil. The critical micelle concentration (CMC) of purified biosurfactant was 35mg/l and the purified biosurfactant inhibited biofilm forming by Bacillus sp..

• Clean Technology
• /
• v.10 no.2
• /
• pp.61-72
• /
• 2004

In this study, aqueous/semi-aqueous cleaning agents which consist of organic solvent, surfactant, cosurfactant, and water were developed by changing formulation parameters such as organic solvent type and contents, surfactant type and contents, and cosurfactant/surfactant(A/S) ratio, etc.. And physical properties and flux removal of the formulated cleaning agents have been evaluated. Also, the performance of oil-water separation from the rinse water contaminated during the cleaning process was evaluated for its recycling. The formulated cleaning agents in this work expected to have good penetration because of their low viscosity and low surface tension values of 30.2~32.5 dyne/cm. The flux removal with the terpene type cleaning agent was higher than that with hydrocarbon type cleaning agent and two commercial products (CPA(commercial product A), CPB(commercial product B)). And the performance of oil-water separation by gravity settling from the rinse water contaminated with formulated cleaning agent and soils was shown to be very good. The cleaning agents developed in this work were applied to surface mounting technology(SMT) cleaning process for manufacturing electronic parts at L electronic company. As a result, the newly developed cleaning agents showed two times better cleaning speed for removal of solder cream than the conventional ond containing ethanol and IPA(isopropyl alcohol). In addition, malodor and VOC problems generated by the previous organic cleaning agents have been solved in the manufacturing field through introduction of the non-volatile and environmental-friendly cleaning agents to the field.

• Clean Technology
• /
• v.11 no.4
• /
• pp.195-204
• /
• 2005

A new condensation process for manufacturing N-acyl taurates which generates less pollutant and produces more than 60 % yield in comparison with the conventional process has been developed in this work. Its optimum process conditions are at $210{\sim}230^{\circ}C$ of reaction temperature and 6 ~ 9 hour of reaction time when Parasol 123 of petroleum refired oil is employed as process solvent and mixed catalysts of sulfonic acid and phosphoric acid are utilized as process catalyst. And the qualities of N-acyl taurates produced by this new process are similar to or better than those of imported product judging from their acid value, amine value and color. Thus, it can be said that the newly developed process for manufacturing N-acyl taurates in this work is better than the conventional process. The physical properties of N-acyl taurates produced in this work such as surface tension, foaming power, foaming stability, hard water stability, and emulsifying power etc. were compared with those of commercially available anionic surfactants. And the experimental results show that N-acyl taurates shows good physical properties and that they can be alternative to conventional anionic surfactants.

• Particle and aerosol research
• /
• v.13 no.4
• /
• pp.151-158
• /
• 2017

Electrostatic precipitator is widely used to remove particulate matters in indoor air and industrial flue gas due to low pressure drop and high collection efficiency. However, it has a low collection efficiency for the submicrometer sized particles. Electrospraying is a potential method to increase the particle charging efficiency, which results in increased collection efficiency. Although particle charging efficiency is highly dependent upon droplet size, the effective measuring method of the droplets is still uncertain. Tap water was electrosprayed in this study, and the images of electrosprayed droplets were taken with a high speed camera coupled with several visualization methods in order to measure the droplets size. The droplet size distribution was determined by an image processing with an image-J program. As a result, a droplet measured by a laser visualization, had a half size of that by a Xenon light visualization. In addition, the experimentally measured droplet sizes were a good agreement with the predicted values suggested by $Fern{\acute{a}}ndez$ de la Mora and Loscertales(1994).