• Journal of the Korean Geotechnical Society
• /
• v.28 no.7
• /
• pp.5-16
• /
• 2012

Soil-nailing is the most popular method of reinforcing for slope stability. In general, two factors are considered as failure modes during the soil-nailing design stages: pullout failure mode and shear failure mode that will occur on the most probable failure plane. In many cases, however, shallow failure can also occur when the ground near the slope face is swept away by the horizontal stress release during the staged top-down excavation. In this paper, an optimized soil-nailing design methodology is proposed by considering the three failure modes mentioned above: pullout failure; shear failure; and shallow failure. The variables to be optimized include the bonded length and number of soil-nailings, and the confining pressure that should be applied at the slope face. The procedure to obtain the optimized design variables is as follows: at first, optimization of soil-nailings, i.e. bonded length and number, against pullout and shear failure modes; and then, optimization of confining pressure at each excavation stage that is needed to prevent shallow failure. Since the two processes are linked with each other, they are repeated until the optimized design variables can be obtained satisfying all the constrained design requirements in both of the two processes.

• Applied Chemistry for Engineering
• /
• v.28 no.6
• /
• pp.638-644
• /
• 2017

Pitch based activated carbon fibers for electric double layer capacitor (EDLC) electrodes were treated by oxyfluorination via varying the ratio of fluorine and oxygen gases to improve high power property. As the partial pressure of fluorine increased, the oxyfluorinated activated carbon fibers showed an increase of linear fluorine functional groups. While the oxygen functional groups increased, no changes was observed with respect to the partial gas pressure. The specific surface area and pore volume decreased due to the etching reaction on the activated carbon fiber surface through oxyfluorination, but the mesopore volume increased about 4.5 times. In the case of activated carbon fibers treated with 50% of the fluorine gas partial pressure, the specific capacitance increased to about 29% and 61% at scan rates of 5 and 50 mV/s, respectively. The improvement of the specific capacitance was believed to be due to the introduction of oxygen and fluorine functional groups on the activated carbon fiber surface and the increase of mesopores through oxyfluorination.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.218-218
• /
• 2016

실린더 형태의 유전체 관에 나선형으로 도전체 안테나를 설치하는 타입의 유도 결합 플라즈마원은 간단한 구조로 화학 조성 분석용부터 나노 분말 제조, 반도체용 식각/증착, 표면 처리, 자동차 및 일반 산업 부품용 증착 보조원등으로 널리 사용되고 있다. 고밀도 라디칼/이온의 공급을 위해서 투입 전력을 증가시키는 경우 높은 전력 밀도로 인해서 유전체 관에 인가되는 열응력이 대기압 및 관 고정용 구조물에 의한 구조 응력에 더해져서 파손에 이르는 경우가 발생될 수 있다. 실제 실린더 길이 전체를 안테나 코일로 감는 경우에도 플라즈마 발생 밀도가 높은 지역은 중심 일부 영역에 국한 되는 공정 영역도 있어서 이에 대한 분석이 필요하다. CFD-ACE+를 이용하여 플라즈마의 생성, 냉각수의 열전도, 외부 공냉식 팬의 역할등에 대해서 수치 모델을 작성하여 검토하였다. 나선형 냉각코일의 경우 냉각수량을 일정값 이상으로 증가시키는 경우 유속이 지나치게 빨라져서 열원이 있는 내경쪽 표면에서 열전도가 유속에 비례해서 증가하지 못하는 단점이 발생할 수 있으며 냉각팬의 경우 일반적으로 장치 내부에 대해서만 모델링을 하는 데 실제로 전체 시스템의 주변에서 공기의 흐름을 넓게 해석해야 실제 냉각 효과를 파악할 수 있다. 심한 경우 냉각용 공기 흡입구와 토출구의 간격이 좁아서 열원에 의해서 가열된 공기의 상당량이 다시 냉각용 공기 흡입구로 재순환 되는 경우도 발생하기 쉽다.

• Journal of the Korean Ceramic Society
• /
• v.33 no.4
• /
• pp.448-454
• /
• 1996

The microstructural evolution of BaTiO3 ceramics during cubic-hexagonal phase transformation was investiga-ted. In the case of phase transformation from cubic to hexagonal BaTiO3 the hexagonal phase nucleated at the surface region of specimen. On the other hand in the case of that from hexgonal phase to cubic, cubic phase was initiated at the center region of specimen. And fast grain growth and irregular grain boundary shape could be also observed during these transformation processes. Besides low densified hexagonal BaTiO3 specimen was made with low forming pressure. The phase transformation of these specimens toward cubic phase was relatively retarded comparing with dense hexagonal BaTiO3 specimens. was made low forming pressure.. The phase transformation of these specimens toward cubic phase was relatively retarded comparing with dense hexagonal BaTiO3 specimens. These results were explained that hexagonal BaTiO3 had lowder surface energy than cubic phase.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1471-1472
• /
• 2011

최근 경재적인 한계를 드러내고 있는 실리콘 태양전지의 대안으로 주목받고 있는 염료감응형 태양전지는 식물의 광합성 원리에 기초하여 빛이 입사하면 염료 분자가 포톤을 흡수해 여기하면서 전자를 방출함으로써 기전력을 발생시키는 원리로 동작한다. 염료에서 발생된 전자는 $TiO_2$의 conduction band로 주입되어 확산을 통해 TCO 기판으로 이동한다. 이때 다공성 나노구조의 $TiO_2$ 표면과 전해질의 접촉이 발생하게 되고 이로 인해 $TiO_2$ conduction band의 전자와 전해질의 $I_3{^-}$ 간의 재결합이 발생하게 되는데 이것은 DSC의 기능을 저하시키는 요인 중의 하나이다. 이러한 문제점은 $Al_2O_3$, ZnO, MgO, $BaTiO_2$ 등의 표면처리에 의한 core-shell 나노구조를 형성함으로써 해결할 수 있다. 본 연구에서는 aluminum isopropoxidee와 magnesium chloride 혼합 용액을 사용하여 core-shell 나노구조를 형성하여 셀을 제작하고, 완성된 셀의 출력특성과 내부 임피던스의 변화를 측정, 분석함으로써 단일 용액을 사용하였을 때에 비해 효과적인 재결합 감소와 광전압의 상승효과를 확인할 수 있었다.

• The Korean Journal of Zoology
• /
• v.36 no.2
• /
• pp.159-174
• /
• 1993

까치 살모사(AEkistrodon snatilis)의 활동기와 동면기에서 일반적인 혈액성상과 혈액내 가스함량의 변화 또한 위장관 점액세포에 대한 형태적 및 조직화학적 변화 양상을 규명 비교하고자 한다 활동기와 동면기에 까치 살모사의 혈액내 총이산화탄소량(TCO2). 이산화탄소부분압(PCO2), 산소압(PO2)과 pH는 활동기보다 동면기에 증가하였으며, 적혈구수, 혈색소, 적혈구 용적 백분율은 활동기보다 동면기에 약간 증가하는 경향이었다. 또한 백혈구수는 활동기보다 동면기에 뚜렷한 감소를 보였다 활동기와 동면기의 위점막에서는 현저한 차이는 없으나, 소장 점막은 동면기에 그 주름수가 감소하고 높이가 낮아지며 점액세포가 위축되었으며, 위 표면 점액세포는 활동기에 중성 점액질과 약간의 Sialomucin을 포함한 산성 점액질로 구성되었으나 동면기에는 중성 점액질과 Sialomucin이 약간 감소하였다 위점액경세포는 활동기에 중성 점액질만을 포함하고 있었으나. 동면기에는Sialomucin을 포함한 산성 점액질이 소량 검출되었다 소장 점액세포는 활동기에 산성점액질과 중성 점액질로 구성되었으며. 산성 점액질에는 Sulfomucin과 Sialomucirr이 포함되어 있었으나 동면기에는 Sulfomucin과 Sialomucin이 다소 감소하는 경향이었다 주사전자현미경 관찰을 통한 까치 살모사의 위장관 표면 상피세포의 미세구조적 변화는 각동면기 별로 차이를 인정할 수가 있었다. 위장관점 막 상피세포는 활동기에 비해 동면기에 상당한 구조적 위축현상을 보이는 경향을 알 수 있다.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.1
• /
• pp.7-12
• /
• 2000

As an essential technology for the FED, VFD and PDP packaging having merits of no glass frit and no glass tube usage, two sodalime glass substrates were electrostatically-bonded in a vacuum environment, and the bond properties were compared with the case of bonding in atmosphere. The glass wafer pairs bonded in vacuum using a-Si interlayer had a relatively lower bond strength than the ones bonded in atmosphere under same bonding conditions (temperature and voltage). And the bond strength was increased in the case of oxygen ambient. Through the XPS and SIMS analyses fur the surface region of a-silicon and bulk glass, it might be concluded that the lower bonding strength was originated from the inactive silicon oxide growth occurred during the electrostatic bonding process due to oxygen deficiency in vacuum.

• 전자공학회논문지 IE
• /
• v.49 no.1
• /
• pp.7-11
• /
• 2012

In this paper, evaluation of physical properties about dielectric relaxation phenomena by the detection of the surface pressures and displacements current on the monolayer films of phospolipid monomolecular DMPC using pressure stimulus. As a result, It is found that the phospolipid monolayer of dielectric relaxation takes a little time and depend on the molecular area. When electric bias is applied across the manufactured MIM device by the deposition condition of phospolipid monomolecular, it is found that be characteristic of insulation generated it wasn't breakdown when the higher electric field to impress by increase of deposition layers.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.9 s.240
• /
• pp.1270-1275
• /
• 2005

Rolling process to fabricate a strip with even thickness is significant to enhance the quality of the strip. The thickness of a strip can be effectively controlled by pair-cross mills. However, pair-cross mill generates thrust in the axial direction of roller and causes skewness, deflection, twist and even accidental roll chock failure. Therefore, accurate estimation of the thrust of the pair-cross mill during rolling process is necessary to monitor the failure of roll and the quality of products. An empirical equation given by Mitsubishi Heavy Industry (MHI) is hitherto employed, where the thrust is expressed in terms of rolling force, reduction ratio and crossed angle. However it turns out that the MHI empirical equation provides somehow inaccurate and unsuitable thrust in practical rolling processes. Moreover, we learn that three parameters involved in MHI equation are coupled each other. In this paper, axiomatic design principle is employed to select appropriate parameters involved in approximate equation in order to make parameters uncoupled. A quadratic equation using response surface method with new parameters is suggested. The accuracy of the approximate model is examined by comparing with real experimental data.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.2
• /
• pp.252-257
• /
• 2011

Magnesium thin films for marine engine parts such as the engine block and the cylinder head cover etc. were prepared on the magnesium alloy(AZ91D) substrate by Thermo-electron activated Ion-plating method. The influence of gas pressure and substrate bias voltages on the crystal orientation and morphology of the films was investigated with X-ray diffraction and field emission scanning electron microscope(FE-SEM), respectively. Moreover, the effect of crystal orientation and morphology of the magnesium films on the its hardness property was investigated as well. From the results, the hardness of the films was increased in Ar gas pressure due to the grain boundary strengthening and occlusion effects.