• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.218-218
• /
• 2016

실린더 형태의 유전체 관에 나선형으로 도전체 안테나를 설치하는 타입의 유도 결합 플라즈마원은 간단한 구조로 화학 조성 분석용부터 나노 분말 제조, 반도체용 식각/증착, 표면 처리, 자동차 및 일반 산업 부품용 증착 보조원등으로 널리 사용되고 있다. 고밀도 라디칼/이온의 공급을 위해서 투입 전력을 증가시키는 경우 높은 전력 밀도로 인해서 유전체 관에 인가되는 열응력이 대기압 및 관 고정용 구조물에 의한 구조 응력에 더해져서 파손에 이르는 경우가 발생될 수 있다. 실제 실린더 길이 전체를 안테나 코일로 감는 경우에도 플라즈마 발생 밀도가 높은 지역은 중심 일부 영역에 국한 되는 공정 영역도 있어서 이에 대한 분석이 필요하다. CFD-ACE+를 이용하여 플라즈마의 생성, 냉각수의 열전도, 외부 공냉식 팬의 역할등에 대해서 수치 모델을 작성하여 검토하였다. 나선형 냉각코일의 경우 냉각수량을 일정값 이상으로 증가시키는 경우 유속이 지나치게 빨라져서 열원이 있는 내경쪽 표면에서 열전도가 유속에 비례해서 증가하지 못하는 단점이 발생할 수 있으며 냉각팬의 경우 일반적으로 장치 내부에 대해서만 모델링을 하는 데 실제로 전체 시스템의 주변에서 공기의 흐름을 넓게 해석해야 실제 냉각 효과를 파악할 수 있다. 심한 경우 냉각용 공기 흡입구와 토출구의 간격이 좁아서 열원에 의해서 가열된 공기의 상당량이 다시 냉각용 공기 흡입구로 재순환 되는 경우도 발생하기 쉽다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.246-246
• /
• 2011

졸-겔 스핀코팅(sol-gel spin-coating)법을 이용하여 실리콘 기판에 ZnO 박막을 증착하였다. 증착된 졸 용액을 전열처리(pre-heat treatment) 후, 다른 속도로 상온까지 냉각시켰다. ZnO 박막의 특성 분석을 위하여 atomic force microscopy (AFM), X-ray diffraction (XRD), Raman, photoluminescence (PL)을 이용하였다. 전열처리 후 5$^{\circ}C$/min의 속도로 천천히 냉각시킨 ZnO 박막은 산맥구조(mountain chain structure)로 표면이 매우 거친 반면, 빠르게 냉각시킨 ZnO 박막은 매우 매끄러운 표면을 나타내었다. 빠르게 냉각시킨 ZnO 박막의 c-축 배향성(c-axis preferred orientation)이 느리게 냉각시킨 ZnO 박막의 배향성보다 더 우세하게 나타났고, 결정성도 우수하였다. 뿐만 아니라, 빠르게 냉각시킨 ZnO 박막의 광학적 특성이 느리게 냉각시킨 ZnO 박막의 특성보다 우수하게 나타났다. 후열처리(post-heat treatment)에 의해 ZnO 박막의 구조적 및 광학적 특성이 더욱 향상되었다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.3
• /
• pp.199-204
• /
• 2017

We introduced a technology for reducing infrared radiation through the active cooling of hot surfaces by using a thermoelectric refrigerator. Certain surfaces were heated by aerodynamic heating, and the heat generation processes are proposed here. We calculated the temperatures and radiations from surfaces, while using thermoelectric refrigerators to cool the surfaces. The results showed that the contrast between the radiations of certain surfaces and the ambient environments can be removed using thermoelectric refrigerators.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.1
• /
• pp.7-11
• /
• 2003

The semiconductor chips or electronic components generate heat, which causes malfunction of the parts when it was not cooled properly. Bulky heat sink and cooling fan are used to get rid of the heat. However, with this bulky system, it is hard to integrate the electronics system in a small scale. The cooling efficiency of the system depends on the surface area of the heat sink, thermal conductivity of the material and the method of integration. In order to develop a novel cooling system, a micro-heatsink with a large surface area while retaining small volume was fabricated by electroless deposition of gold/copper inside a Track-etched membrane. The structure of the micro-heatsink was investigated using SEM or optical microscope. It was also found that the micro-heatsink is more efficient than a flat copper plate.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.11
• /
• pp.983-990
• /
• 2010

In the present study, spray cooling heat transfer was experimentally investigated for the case in which water is sprayed onto the surfaces of micro-fins in forced convection and nucleate boiling regions. The experimental results show that an increase in the droplet flow rate improves heat transfer due to forced convection and nucleate boiling in the both case of smooth surface and surfaces of micro-fins. However, the effect of subcooling for fixed droplet flow rate is very weak. Micro-fins surfaces enhance the spray cooling heat transfer significantly. In the dilute spray region, the micro-fin structure has a significant effect on the spray cooling heat transfer. However, this effect is weak in the dense spray region. A previously determined correlation between the Nusselt number and Reynolds number shows good agreement with the present experimental data for a smooth surface.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.12
• /
• pp.1051-1056
• /
• 2014

After hot rolling, a high-temperature steel plate with a temperature higher than $800^{\circ}C$ is rapidly cooled by multiple circular water jets. In this cooling process, because the temperature of the steel plate is much higher than the boiling point of the cooling water, film-boiling heat transfer occurs and a very thin steam layer forms between the plate surface and the cooling water. The steam layer acts as a thermal resistance that prevents heat transfer between the cooling water and the steel plate. In addition to the film-boiling heat transfer, complex physical phenomena such as the free-surface flow of residual water that accumulated on the material and the material's high-speed motion also occur in the cooling process. In this study, the simultaneous cooling process of the upper and lower sides of a running hot steel strip is investigated using a three-dimensional numerical model and the cooling performances and characteristics of the upper-side cooling and lower-side cooling are compared.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.69-76
• /
• 2018

The present study analyzed the effect of film hole position of 45 degree ribbed cooling channel on film cooling performance of gas turbine blades. We also investigated the influence of the ribs under the fixed blowing ratio. Three-dimensional numerical model was constructed and extensive simulation was conducted using the commercial code (Fluent ver. 17.0) under steady-state condition. Base on the simulation results, We investigated the cooling effectiveness, flow velocity, streamline, and pressure coefficient. Moreover, We analyzed the effect of cooling hole position on ejection of the secondary flow caused by the rib structure. From the results, It was found that internal flow of the cooling channel forms a vortex pair in the counterclockwise from the top side, and clockwise from the bottom side. For the channels with ribs, the vortex flow generated by the ribs caused a higher pressure difference near the hole outlet, resulting in at least 12% higher cooling effectiveness than the channel without ribs. Additionally, when the hole is located on the left side of the ribbed channel (Rib-Left), it can be found that the secondary flow generated by the ribs hits against wall surface near the hole to form a flow in the direction of the hole inclination angle. Therefore, It is considered that the region where the cooling gas discharged to the blade surface stays in the main flow boundary layer is wider than the other cases. In this case, The largest pressure coefficient difference was observed near the outlet of the hole, and as a result, the discharge of the cooling gas was accelerated and the cooling efficiency was slightly increased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.2
• /
• pp.624-631
• /
• 1996

This study describes extinguishment mechanism of the purely buoyant diffusion flame using the water spray. Experiments are systematically carried out for the oul pool fire with the six different atomizing nozzles. From the measurement of burning rate which represents the combustion intensity of fire, it is observed that the water spray is able to act to enhance fire rather than to extinguish fire. The air entertainment due to the water spray is visualized to understand this phenomenon, acting to enhance fire. In order to observe effects of droplet size on fire extinguishment, and amount of water which reaches the flame base, fuel surface, and mean diameter of droplets are measured. When water droplets are too small, they do not reach the flame base because they can the water spray having too small doplets is ineffective for extinguishment of the oil fire.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.5
• /
• pp.67-72
• /
• 2008

The film cooling effectiveness on a flat plate measured by pressure sensitive paint technique. Six film cooling hole were fabricated on a flat plate with 30 degree angle with respect to the surface and three blowing ratios of 0.5, 1, and 2 were tested. Results showed that PSP technique successfully evaluated the distribution of film cooling effectiveness and showed similar results with references. The film cooling effectiveness near the film cooling holes was higher for lower blowing ratio case. As the blowing ratio was increased, the film cooling effectiveness near the film cooling hole decreased due to the lift off of the coolant. At far downstream, the film cooling effectiveness for higher blowing ratio was higher due to the coolant reattachment.

• Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
• /
• 2003.10a
• /
• pp.205.2-205
• /
• 2003

가정에서는 쌀을 소비할 때 외기 조건 특히, 하절기와 같이 외기 온도가 높을 경우 함수율 감소, 지방산가 증가 및 해충발생 등 품질 손상이 급격히 발생한다. 따라서, 가정에서 쌀을 소비할 때 쌀의 품온을 가능한 낮춰 안전하게 저장하는 방법이 필요하다. 본 연구는 가정용 냉각쌀통을 이용하여 저온에서 쌀을 저장하면서 저장기간 중 품질변화를 측정하여 저온저장특성을 구명하는데 목적이 있다. 가정용 냉각쌀통은 매직 쌀장고(MRH-2501, Tongyang)를 이용하였으며, 대조구로 상온($25^{\circ}C$)에서 쌀을 14주간 저장하면서 1주일 간격으로 시료를 채취하여 함수율, 지방산가, 색도 및 표면변화를 측정하였다. 저장기간이 경과함에 따라 쌀의 함수율은 냉각쌀통의 경우 1.5%(w.b.), 상온저장의 경우 2.1%(w.b.)가 감소하였다. 지방산가는 냉각쌀통에서 저장 14주 후15.1(mg KOH/100g)로 나타났고, 상온저장에서는 8주 후 24.2, 14주 후에는 40.9(mg KOH/100g)로 급격히 증가하였다. 쌀의 색도는 저장기간이 경과함에 따라 증가하는 경향으로 나타났으며, 상온저장이 냉각쌀통에 비해 현저히 높게 증가하였으며, 저장 8주 후부터는 유의적인 차이를 나타내었다. 쌀의 표면에 세포벽은 냉각쌀통에 비해 상온저장에서 저장기간이 경과함에 따라 뚜렷하게 나타났다.