• Journal of Korea Water Resources Association
• /
• v.32 no.6
• /
• pp.721-730
• /
• 1999

A Grid-based daily evapotranspiration(ET) prediction model which calculates temporal and spatial ET with a complementary relationship of Morton(1983) was developed. The model was programmed by C-language and uses ASCII formatted map data of DEM(Digital Elevation Model) and land use. Daily ET within the watershed is calculated and the results of temporal variations and spatial distributions of ET are presented by using GRASS(Geographic Resources Analysis Support System). To verify the applicability of the model, it was applied to the part of Bocheong stream basin (76.5$\textrm{km}^2$) located in the upstream of Dacheong Dam watershed. The result shows that the estimated evapotranspiration in 1995 was 766.1mm and 22% increased after correction radiation for slope and area.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.32 no.5
• /
• pp.527-537
• /
• 2014

In 2013, NGII(National Geographic Information Institute) has developed and provided the KNGeoid13(Korean National Geoid Model 2013) to support the fundamental computation of GNSS-derived orthometric height. In this study, the adjusted ellipsoidal height, the sum of geoidal height and height by the leveling, is applied to calculate the GNSS-derived orthometric height without the local bias, based on GNSS static surveying and KNGeoid13. The mean of errors in GNSS-derived orthometric heights could be verified with the leveling data, which was actually less than 0.5 cm with using the adjusted ellipsoidal heights, but 3 cm by calculating differences between ellipsoidal heights and geoidal heights. By analyze the accuracy of GNSS-derived orthometric height depending on the duration of observation, we could realized 95% of data shows less than 4 cm accuracy, when the GNSS survey conducting for 4 hours spread over two days, but while the case of GNSS survey conducting for 4 hours and 2 hours respectively, resulted in 95% of data less than 5cm level of accuracy. Also, if the ambiguity is fixed, less than 10cm of accuracy could be obtained at 95% of data for only 30 minutes GNSS survey over a day. Following the study, we expected that the height determination by GNSS and geoid models can be used in the public benchmark surveying.

• Journal of Mushroom
• /
• v.15 no.4
• /
• pp.202-205
• /
• 2017

The potential risk of heavy metals and residual pesticides in imported sawdust media inoculated with oak mushroom cultures is a concern for safe mushroom production in Korea. To obtain preliminary data for a sound analysis of this risk, this study was undertaken to analyze the presence of heavy metals and residual pesticides in the oak mushroom media imported from six different regions in China, between 2013 and 2015. Lead, arsenic, chrome, mercury, and cadmium were analyzed; arsenic, chrome, and mercury were not detected. Lead was detected in the imported oak mushroom media from Jinlin, Shandong, Liaoning, and Tianjin. The detection level of lead ranged from 1.7 to 3.2 mg/kg. Cadmium was detected at a level of 0.028 to 0.037 mg/kg in the media from Shandong and Liaoning. No residual pesticides were detected in any of the samples.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.53 no.1
• /
• pp.102-109
• /
• 2008

This study was performed to obtain fundamental information on growth adaptability and isoflavone contents of soybean cultivars in highland area of Korea. For this study, we cultivated nineteen cultivars and investigated yield and isoflavone contents. In Jinbu-myeon located at altitude of 600 m, most of cultivars showed more than 2.5 t/ha seed yield except three cultivars, and the range of isoflavone contents among nineteen cultivars was 715 to $2,545\;{\mu}g/g$. Cultivars with both high seed yield and isoflavone contents were Manrikong, Sinpaldalkong2, Cheongjakong, and Cheongjakong2 in this area. In Daegwallyeong-myeon located at altitude of 800 m, the range of seed yield and isoflavone contents was 1.4 to 2.4 t/ha and 437 to $2,370\;{\mu}g/g$, respectively. Cultivars with both high seed yield and isoflavone contents were Ilpumgeomjeongkong and Dooyookong in this area. Cultivars selected on the basis of seed yield and isoflavone contents in 2004 and 2005 showed also similar results for yield and isoflavone contents at farmer's field in highland area in 2006. In conclusion, it could be expected to produce soybeans having both higher yield and better quality if the selected soybean cultivars are cultivated in highland area.

• Korean Journal of Food Science and Technology
• /
• v.19 no.6
• /
• pp.550-555
• /
• 1987

Strain gauges attached on the Bourdon tube and load cell were used as the sensors for measuring the vacuum pressure in drying chamber and the weight loss of Shiitake mushrooms respectively. The vacuum drying system was interfaced further with the Bear II microcomputer. The interface devices used were built with such IC chips as MC 6821, ADC 0809, SN 74244 and SN 7424. The relationship between readings of vacuum gauge (P, mmHg) and digital outputs (D) from the microcomputer was represented by P =3.08 D-13.4875(r=0.9999). The weights of drying sample (W) were also related with the digital outputs (D) by W=0.4076 D-6.4762 (r=0.9999). During the vacuum drying of Shiitake mushrooms. the data on pressure and weight were recorded at regular intervals using an acquisition program on the microcomputer system. The Page model was fitted well to the drying data of Shiitake mushrooms. resulting in the following empirical equations : $(M-M_e)/(M_o-M_e)=\exp(-0.1569t^{1.0048})$ at 400 mm Hg up to 14 hours and $(M-M_e)/(M_o-M_e)=\exp(-0.1385_t^{1.2688})$ at 600 mm Hg up to 8 hours.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.36 no.2
• /
• pp.250-254
• /
• 2007

In an attempt to find ways of improving the quality of dried Shiitake mushroom, this study compared a conveyer-type far-infrared drying method with a traditional heated air drying method. The conveyer-type far-infrared dryer was performed at air velocity of 0.6 and 0.8 m/s under drying air temperature of 60, 70 and $80^{\circ}C$, respectively. Drying characteristics, antioxidant activities and the antioxidant compounds of Shiitake mushroom dried by far-infrared dryer were investigated. Generally, drying rate with the conveyer-type far-infrared drying method was faster than that with the traditional heated air drying method. In the conveyer type far infrared drying method, drying rates were increased with increasing temperature and air velocity. The loss of antioxidant activities during the conveyer-type far-infrared drying method at 60-0.6, 60-0.8, and $70^{\circ}C-0.6m/s$ was less than the traditional drying method. However, the loss of antioxidant activities at 70-0.8, 80-0.6, and $80^{\circ}C-0.8m/s$ was higher than that of the traditional drying method. Therefore, the conveyer type far infrared drying conditions with below $70^{\circ}C$ and 0.6 m/s air velocity may produce dried Shiitake mushroom with relatively higher antioxidant activities and antioxidant compounds.

• Journal of Mushroom
• /
• v.20 no.1
• /
• pp.22-28
• /
• 2022

In order to provide basic data for preparing management standards and to verify the safety of the Chinese oak mushroom-derived moisturizing medium-which is synthesized and imported in large quantities-the presence of 321 residual pesticides, 7 heavy metals, and 3 radioactive materials was analyzed in the moisturizer samples. Examination of residual pesticides in seven moisturizing medium samples prepared using the Chinese oak mushroom and three domestic sawdust samples used for mushroom culture revealed the presence of cypermethrin and iprodione in three moisturizer samples, but the contents of these pesticides were below the standard limits. Zn was detected in ten samples, Cu was detected in nine samples, and Ni was detected in four samples, but their contents were below the standard limits. Pb, Cd, Cr, and Hg were not detected in any sample. No radioactive materials were detected in the samples. In addition, fruiting bodies of the oak mushroom were observed in each medium. Examination did not reveal the presence of any residual pesticides or harmful compounds. In this study, the use of the moisturizing medium prepared using the Chinese oak mushroom was found to be safe. As residual pesticides, heavy metals, and radioactivity-even in trace amounts-remain concentrated in the human body, continuous verification of the safety of hazardous substances and pollutants during the systematic cultivation and management of these mushrooms is required.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2003.09a
• /
• pp.222-226
• /
• 2003

경남 밀양지역의 대수층별 지하수위 분포 특성을 파악하기 위하여 2002년 봄에 총 503개 지하수공을 대상으로 지하수위를 측정하였다. 조사된 자료는 수치가 낮은 지점들에 집중되어 있어 정규분포를 이루지 않으나, 대수변환 된 자료는 정규분포를 나타내었다. 표고와 천층 및 심층 지하수위의 회귀 분석을 실시한 결과, 모두 정(＋)의 상관관계가 높은 것으로 나타났다. 베리오그램 분석이나 교차 베리오그램 분석 결과, 원시자료보다 대수변환 된 자료가 반베리오그램이나 교차 반베리오그램의 적합선에 더 잘 맞는 것으로 나타났다. 교차 타당성 분석 결과, 천층 지하수위에 대한 정규크리깅 및 코크리깅 모델링에서 원시 자료가 대수변환 된 자료보다 추정치에 더 가깝게 나타났고, 심층 지하수위에 대한 정규크리깅 및 코크리깅 모델링에서는 원시 자료보다 대수변환 된 자료가 추정치에 더 가깝게 나타났다. 정규크리깅이나 코크리깅을 이용하여 작성된 대수층별 지하수위 등고선도에서 등고선의 분포는 대체로 비슷하지만, 코크리깅에 의해 작성된 지하수위 등고선도가 정규크리깅에 의한 지하수위 등고선도보다 더 정밀한 것으로 나타났다. 이것은 원시 자료뿐만 아니라 대수변환 된 자료를 이용한 지하수위 등고선도에서도 같은 결과가 도출되었다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.140-140
• /
• 2017

최근 기후변화에 따른 태풍과 국지성 집중호우의 증가로 국토의 64%가 산지인 우리나라에서는 재해의 위험성을 증가시키고 있다. 재해 분석에 있어 기초자료로 사용되는 지형자료의 정확도는 재해분석결과에 있어 중요하며, 지형촬영방법에 따라 정확도의 차이가 매우 크다. 지형자료 중 하나인 DEM(Digital Elevation Model) 활용분야 또한 확대되고 있고 지도제작에 있어 DEM을 사용하면 지형도를 신속히 제작할 수 있고, 편집 용이, 수작업 인원 감축, 정확도 향상 및 데이터베이스의 구축이 이루어져 체계적으로 종합적인 지형정보를 관리할 수 있는 장점이 있다. 지상 LiDAR를 이용하여 생성한 DEM은 매우 정확한 방법이며, 접촉식 측량장비에 비하여 누락되는 데이터가 적으며 정밀하게 자료를 수집가능 한 것이 장점이다. 지상LiDAR를 이용한 자료 취득 시식생과 구조물에 의해 촬영 각도가 제한되는 경우 충분한 자료를 얻기 위해 여러 위치에서 스캔이 필요하다. 한편 전 세계적으로 드론의 도입으로 인해 다양한 분야에서 높은 가능성을 가지고 활용되고 있는 실정이며, 드론을 이용한 연구들도 활발히 진행 중이다. 소규모 및 중간 규모의 하천, 산지 등의 현장 조사의 경우 LiDAR장비의 진입이 어려운 구간의 촬영 시 드론을 활용하면 보다 효율적일 것으로 예상된다. 이에 따라 본 연구는 지상LiDAR와 드론을 이용하여 얻은 DEM 자료를 비교 분석하여 드론으로 생성된 DEM 자료 활용 가능성 여부를 검토하였다. 본 연구에서는 동일한 지역에 지상LiDAR와 드론 촬영을 실시하여 지형자료를 각각 획득한 후 후처리 프로그램을 이용하여 영상분석을 실시하였다. 또한 측점을 선정한 후 지형 좌표의 편차, 표고의 편차 등을 비교분석하였다.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.27 no.5
• /
• pp.545-553
• /
• 2009

Digital Elevation Models (DEM) is widely used in establishing the topographic profile in nation spatial information. Aerial Light Detection And Ranging (LiDAR) system is one of the well-known means to produce DEM. The system has fast data acquisition procedures and less weather-dependent restrictions compared to photogrammetric approaches. In this regards, LiDAR has been widely utilized and accepted in the process of nation spatial information generation due to its sufficient positional accuracy. However, the investigation of the accuracy of aerial LiDAR data over the area of forestation with various kinds of vegetations has been barely implemented in Korea. Hence, this research focuses on the investigation of the accuracy of aerial LiDAR data over the area of forestation and the evaluation of the acquired accuracy according to the characteristics of the vegetations. The study areas include land with shrubs and its adjacent forest area with mixed tree species. The spots for the investigation have been selected to be well-distributed over the whole study areas and their coordinates are surveyed by Global Positioning Systems (GPS). Then, the surveyed information and aerial LiDAR data have been compared with each other and the result accuracy has been evaluated. Conclusively, it is recommended that LiDAR data collection to be conducted after defoliation period, especially over the areas with broadleaf trees due to the possibility of significant outliers.