• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.772-779
• /
• 2000

The friction and wear behavior of short carbon fiber reinforced polyetheretherketone was studied experimentally under dry sliding conditions against SCM440(AISI 4140) disks with a different surface roughness and hardness at the low sliding speeds and the high pressures on a pin-on-disk apparatus. Under the low disk surface roughness value the earsplitting noise and stick-slip were occurred. The increased adhesion friction and wear factor with stick-slip made the friction and wear behavior worse. Under the high disk surface hardness the break and falling-off of carbon fibers were accelerated. The carbon fibers fallen off from the matrix were ground into powder between two wear surfaces and this phenomenon caused a abrasive friction and wear factor to increase. So the friction and wear behavior became worse. With the transfer film made of wear particles formed on a disk, the carbon powder film formed on a pin lowered a friction coefficient.

• 한국전기화학회:학술대회논문집
• /
• 2005.07a
• /
• pp.83-86
• /
• 2005

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.6
• /
• pp.930-937
• /
• 2001

The friction and wear behavior of short carbon fiber reinforced polyetheretherketone was studied experimentally under dry sliding conditions against SCM440(AISI 4140) disks with different surface roughness and hardness at the low sliding speeds and the high pressures on a pin-on-disk apparatus. Under the low disk surface roughness value the earsplitting noise and stick-slip were occurred. The increased adhesion friction and wear factor with stick-slip made the friction and wear behavior worse. Under the high disk surface hardness the break and falling-off of carbon fibers were accelerated. The carbon fibers fallen off from the matrix were ground into powder between two wear surfaces and this phenomenon caused abrasive friction and wear factor to increase. So the friction and wear behavior became worse. With the transfer film made of wear particles formed on a disk, the carbon powder film formed on a pin lowered a friction coefficient.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.1
• /
• pp.17-23
• /
• 2017

Polyether ether ketone (PEEK) composite including tungstophosphoric acid(TPA) membranes have been intensively investigated for polymer electrolyte membrane water electrolysis (PEMWE) and thus covalently linked sulfonated polyether ether ketone (CL-SPEEK) with captured TPA composite membranes were prepared and characterized. Sulfonated polyether ether ketone (SPEEK) was prepared in sulfonation of PEEK and was cross-linked with 1,4 diiodobutane. The carbonyl group of SPEEK was reduced with $NaBH_4$ and 3-isocyanatepropyltriethoxysilane (ICPTES) was added. The TPA captured composite was prepared in reaction of TPA with 3-mercaptopropyltrime thoxysilane (MPTMS). The polymer composite membranes showed better thermostability and electrochemical properties than SPEEK. The membranes were prepared by sol-gel casting method. The polymer composite membrane featured 0.1285 S/cm of proton conductivity at $80^{\circ}C$ and outstanding durability.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.4
• /
• pp.338-344
• /
• 2017

Polyoxometal molybdophosphoric acid (MoPA) bonded polyether ether ketone (PEEK) composite membrane for water electrolysis has been investigated. The composited membrane, covalently cross linked (CL) sulfonated polyether ether ketone (SPEEK) with a bonded MoPA, was prepared in sulfonation of PEEK, cross linkage reaction with 1,4-diiodobutane, and addition with MoPA. PEEK was covalently cross-linked with 1,4-diiodobutane to improve mechanical strength and was added with MoPA to increase proton conductivity. MoPA should be fixed to back bone of SPEEK to prevent bleeding out. Therefore, the carbonyl group of SPEEK was reduced with NaBH4 and 3-isocyanatepropyltriethoxysilane (ICPTES) was added. The MoPA bonded composite was produced in the reaction of MoPA with 3-mercaptopropyltrimethoxvsilane (MPTMS). In conclusion, MoPA bonded CL-SPEEK composite membrane featured 0.129 S/cm of proton conductivity at $80^{\circ}C$, and 2,156 hours of chemical stability in Fenton test. These properties are better than those of membranes of other SPEEK system.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.5
• /
• pp.478-484
• /
• 2016

Polyether ether ketone (PEEK) composite membranes have been intensively investigated for polymer electrolyte membrane water electrolysis (PEMWE). Covalently linked (CL) sulfonated polyether ether ketone (SPEEK) and cellulose polymer composite membranes were prepared and characterized. Polyether ether ketone (PEEK) and cellulose were sulfonated and then were covalently linked by 1,4-diiodobutane to produce covalently linked SPEEK and cellulose polymer composite membranes. The composite membranes showed better thermostability and electrochemical properties than SPEEK. The membranes were prepared by sol-gel casting method. CL-SPEEK/Cellulose composite membrane featured 0.2453 S/cm of proton conductivity at $80^{\circ}C$ which was better than that of Nafion.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.85.2-85.2
• /
• 2010

There is widespread effort to develop polymer membranes in place of Nafion for high temperature polymer electrolyte membrane fuel cell(PEMFC). In our study, SiO2 membranes are arranged by electrospinning method. For impregnation solution, the modified sulfonated poly(ether ether ketone)(SPEEK) polymer is prepared from sulfonation, sulfochlorination, partial reduction and lithiation reaction. The modified polymer is cross-linked with 1,4-diiodobetane in NMP solvent and then blended with Heteropoly acid(HPA). The characterization of membranes is confimed by FT-IR, Thermogravimetry(TGA), water uptake test and single cell performance test for PEMFC, etc. The composite membrane shows satisfactory thermal and mechanical properties. Beside, The membrane exhibits good ion exchange capacity and high proton conductivity. As a result, The composite membrane is promising as an alternative membrane in high temperature PEMFC.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1993.10a
• /
• pp.32-33
• /
• 1993

근래 환경 문제의 중요성이 크게 대두되면서 여러 제조 공정에서 방출되는 폐수등을 처리하는데 막분리 공정을 이용하려는 연구가 진행되고 있다. 이 공정에 필요한 내구성, 내 미생물성, 내 약품성등이 우수한 역삼투막 재료를 얻기 위한 방법의 하나로 엔지니어링 플라스틱을 친수화 시키는 방법이 개발되어 왔는데, 구체적으로는 설폰화등의 친수화가 된 폴리설폰(polysulfone), 폴리 에테르 에테르 케톤(poly ether ether ketone), 폴리 이미드(polyimide) 수지등이 검토되고 있다. 특히 PPO(poly(2,6-dimethyl-1,4-phenylene oxide))로 만들어진 분리막은 내산화성이 우수하고 내구성이 뛰어나다고 알려져 있다. 본 연구에서는 PPO를 유기 금속 반응을 이용하여 carboxylation시키고 이 carboxylated PPO로 역삼투막을 제조하여 투과특성을 조사하였다.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2005.05a
• /
• pp.144-147
• /
• 2005

• Transactions of the Korean hydrogen and new energy society
• /
• v.29 no.5
• /
• pp.411-418
• /
• 2018

The polymer electrolyte membranes, CL-SPEEK/Cellulose composite membrane I, II, III with the improved electrochemical and mechanical properties were prepared and characterized. The engineering plastic polyether ether ketone (PEEK) and cellulose were sulfonated and cross-linked. The membranes were prepared by sol-gel casting method with different amount of cross-linking reagent. In conclusion, the composite membranes I, II, III showed improved thermostability, tensile strength and oxidative durability. Proton conductivity of the membranes was also improved and the composite membrane I showed 0.1312 S/cm at $80^{\circ}C$ which was the best of those composite membranes.