• Polymer(Korea)
• /
• v.37 no.6
• /
• pp.753-763
• /
• 2013

Laser transmission welding of polymers is now used in a very wide range of industries due to its advantages. If the joining between polypropylene (PP) and polycarbonate (PC) occurs by laser transmission welding, the automotive headlight will get a large profit. However, PP/PC have poor miscibility. In the laser transmission welding results, the adhesion strength between PP and PC was very weak. In this study, PP was modified by grafting of glycidyl methacrylate (GMA). The adhesion strength of PC and PP-g-GMA as a reactive compatibilizer was observed. The adhesion strength was investigated by compatibility with PC, mechanical properties and laser transmission welding.

• Polymer(Korea)
• /
• v.30 no.4
• /
• pp.318-325
• /
• 2006

Polypropylene-clay nanocomposites were studied by the modification of clay with amino silanes to introduce covalent bonds in nanocomposites, and prepared by melt-compounding with polypropylene, clay modified with amino silanes and maleic anhydride grafted polypropylene. The . .structure and surface properties of modified clay were determined by x-ray diffraction, infrared spectrum, and solid-state $^{29}Si$ nuclear magnetic resonance spectrum. The modification of clay with aminosilanes led to the increase of the silicate interlayers to about $19.8{\AA}$, the weakening effects of hydroxy group at $3650cm^{-1}$ and the signal of amine groups at -69 ppm proved that the modification had taken place.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.88-97
• /
• 2002

The effect of aminosiloxane modifier on the chemorheological properties of ortho-cresol novolac epoxy/phenol novelac/triphnylphosphine resin system was investigated aat different isothermal curing temperatures. By adding the aminosiloxane to the resin system, not only conversion rate and conversion were increased but also glass transition temperature was promoted. Critical conversion and gelation time obtained at the crossover point between storage and loss moduli were reduced and thus the viscosity was increased by the aminosiloxane. $C_1$ and $C_2$ in the WLF equation calculated from the glass transition temperature as a function of conversion and measured viscosity were found to vary with the curing temperature. By applying the change of glass transition temperature with conversion, $C_1$ and $C_2$ to WLF equation, it was possible to predict accurately the viscosity change with isothermal curing reaction.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.47-51
• /
• 2011

In this study, illite, an environmental friendly, low cost, and high aspect ratio additive, was used to improve flame retardant property of epoxy and it was fluorinated to enhance dispersion of hydrophilic illite in hydrophobic epoxy by introducing hydrophobic functional groups. Fluorination of illite enhanced illite dispersion ill epoxy solution before curing and that in the complex after curing. These enhanced dispersions were attributed to the increased affinity of illite to hydrophobic epoxy solution induced by fluorination of illite and the increased intercalation of epoxy polymer or exfoliation of illite by epoxy curing. Hence, limited oxygen index(LOI) of fluorinated illite/epoxy complex increased by 24%, compared to that of epoxy, suggesting that the preparation of fluorinated illite/epoxy complex increased their flame retardant properties.

• Polymer(Korea)
• /
• v.36 no.5
• /
• pp.579-585
• /
• 2012

Polystyrene/carbon nanotube (CNT) microcellular foams were prepared to have electrically conductive properties via high internal phase emulsion polymerization. In this study, we have investigated the effects of surface modification of CNT, surfactant content and dispersion time to improve the stability of emulsion and the electrical conductivity of foam. Acid treatment and a surfactant were used to effectively disperse CNTs in the aqueous phase. In the organic phase, CNTs were used after a surface modification with organic functional groups. The degree of dispersion of CNTs was estimated by the electrical conductivity of resultant microcellular foams. With raw CNTs dispersed with the surfactant in the aqueous phase, substantial conductivity increase was observed but the foams were slightly shrunk. The foams prepared with organically modified CNTs dispersed in the organic phase showed stable cell morphology without shrinkage, but displayed limitation to improve the conductivity.

• Polymer(Korea)
• /
• v.39 no.2
• /
• pp.300-310
• /
• 2015

In this study, we modified silica nanoparticles with N-[3-(trimethoxysilyl)propyl]ethylenediamine (TPED) silane coupling agent, which has one primary and one secondary amino groups in a molecule, to introduce amino groups on the silica surface. After modification of silica, we used 3-(acryloyloxy)-2-hydroxypropyl methacrylate (AHM) to introduce methacrylate groups by Michael addition reaction. We found about 30% of N-H groups on the TPED modified silica surface reacted with acrylate groups of AHM compared to about 85% of reaction between N-H groups of pure TPED with acrylate groups of pure AHM. This lower degree of Michael addition reaction for heterogeneous reaction between N-H groups on the solid TPED modified silica and liquid AHM compared to homogeneous reaction between pure liquid TPED and pure liquid AHM may be caused by lower mobility of grafted amino groups of TPED moiety and higher steric hindrance caused by solid silica particles.

• Polymer(Korea)
• /
• v.28 no.5
• /
• pp.374-381
• /
• 2004

Gas permeability of low density polyethylene (LDPE) film containing zeolite powder for $CO_2,\;O_2$ and $N_2$ were investigated. Zeolite powders modified by cations or surfactant were compounded with LDPE to produce $20 wt\%$ masterbatch. After blending the masterbatch with LDPE, zeolite filled films were prepared by the blown film process. Finally, the composite films containing zeolite loadings of 0, 3,5, and $10 wt\%$ were produced. A gas permeability apparatus based on the variable volume principle was designed to analyze the characteristics of films. Experiments showed a general trend that gas permeabilities first decreased and then increased as the zeolite content was increased. Surfactant modified zeolite showed a better interfacial adhesion with the matrix, but the film did not show a discernible difference in gas permeability compared with the other modified films. The difference of temperature dependences in the gas permeabilities of composite films was slightly smaller than that of LDPE film.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.2
• /
• pp.124-134
• /
• 2013

This study investigated the effect of surface water on concrete substrate on adhesive strength in tension of very high flowable SBR-modified cement mortar. The specimens were prepared with proportionally mixing SBR latex, ordinary portland cement, silica sand, superplasticizer and viscosity enhancing agent. Polymer cement ratio (P/C) were 10, 20, 30, 50 and 75% and the weight ratio of fine aggregate to cement were 1:1 and 1:3. The specimens obtained with different P/C and C:F were characterized by unit weight, flow test, crack resistance and adhesion test. After basic tests, two mixtures of P/C=20% and 30% in case of C:F=1:1, and one mixture of P/C=50% in case of C:F=1:3 were selected, respectively. These three selected specimens were studied about the effect of surface water evenly sprayed on concrete substrate by a amount of 0, 0.006, 0.012, 0.017, 0.024g per unit area ($cm^2$) of concrete substrate surface The results show that surface water on concrete substrate increases the adhesive strength in tension of high flowable SBR-modified cement mortar and improve the flowability compared to the non-sprayed case.

• Polymer(Korea)
• /
• v.38 no.1
• /
• pp.74-79
• /
• 2014

Microfibrillated cellulose (MFC) was chemically modified with two different silane coupling agents (3-aminopropyltriethoxysilane and 3-mercaptopropyltriethoxysilane) and lauroyl chloride. The surface modification of MFC was confirmed by infrared spectroscopy (FTIR), energy dispersive X-ray spectroscopy (EDX), and contact angle measurements. Composite paper was successfully prepared with surface modified MFC and polyamide (PA) fiber. The surface modification of MFC not only prevented aggregation of MFC but also improved adhesive property between PA fiber and surface modified MFC. It was impossible to prepare papers of only PA fiber because there is no binder to connect PA fibers. That is, surface modified MFC as a binder in PA fiber played a crucial role in making composite paper. Composite paper with silane modified MFC showed higher tensile strength and modulus than composite paper with lauroyl moiety modified MFC. The structure, morphology, and mechanical properties of composite paper were analyzed by scanning electron microscope (SEM) and universal testing machine (UTM).

• Journal of Periodontal and Implant Science
• /
• v.33 no.1
• /
• pp.27-35
• /
• 2003

1. 목적 생체재료의 생체친화성을 증진시키고 치유를 촉진하기 위한 목적으로 생체재료의 생화학적 표면개질에 관한 연구가 널리 진행되고 있다. 이와 같은 목적으로 이용되어 온 부착분자에는 아미노산, 펩타이드, 단백질, 효소 및 성장인자들을 들 수 있으며, 이들 분자들을 금속, 골대체물질 및 폴리머와 같은 생체재료의 표면개질에 이용하여 왔다. 이 연구의 목적은 생체적합성이 우수하고 생분해성을 지닌 키토산으로 얇은 막을 제작한 후, 세포외 기질의 구성성분 중 세포부착에 관여하는 RGD 펩타이드를 부착시킨, 표면개질 키토산막의 생물학적 영향을 MG-63 조골양세포를 이용하여 관찰하는 것이다. 2. 방법 2% acetic acid에 키토산 가루를 녹여 만든 2% 키토산 용액으로 24-well 배양접시의 표면을 도포 후 24시간 동안 건조시켜 키토산막을 제작하였다. GRGDS 펩타이드를 cross-linker(EDC, NHS) (Sigma, MO, USA) 용액과 반응시켜서 펩타이드의 카르복실기를 활성화시켰다. 이들을 PBS 완충용액으로 수화시킨 키토산막과 결합시켜 펩타이드의 활성화된 카르복실기와 키토산의 아민기 간에 안정적인 아미드 결합(amide bond)이 형성되도록 하였다. 하루 동안 반응을 일으킨 후 PBS 완충용액과 증류수로 씻어내고 냉동 건조시킴으로써 GRGDS가 결합된 키토산막을 제작하였다. 재료 표면의 화학 성분을 알아보는데 사용되는 방법의 일종인 X-ray photoelectron spectroscopy(XPS) 분석을 통하여 부착분자가 키토산막에 결합된 여부를 확인하였다. GRGDS 펩타이드에 요오드를 결합시킨 후, 이것을 키토산막에 공유 결합시키고 XPS를 통해 요오드가 재료 표면에서 검출되는지를 검사하였다. 요오드가 검출된다면 이것은 키토산막 표면에 실제로 GRGDS 펩타이드가 존재하는 것을 의미하게 된다. 표면개질된 키토산막에 사람조골양세포인 MG-63을 접종하여 이를 실험군으로 하였고, 표면이 개질 되지 않은 키토산막을 대조군으로 하였다. 세포부착의 최적화 농도를 확인하기 위하여 GRGDS를 0.01, 0.05, 0.1, 0.25, 0.5, 1.0mg/ml의 농도로 준비하였다. 배양 후 1일, 7일째에 각 well에서 trypsin EDTA를 이용하여 세포를 분리한 후, 이를 원심 분리하여 세포수측정기를 이용하여 부착 세포의 수를 측정하여 세포의 부착 정도를 비교하였다. 배양 2시간, 24시간 후 주사전자현미경을 이용하여 키토산막에 부착된 세포의 양상을 관찰하였다. 3. 결과 XPS를 통한 표면의 화학 성분 분석 결과 GRGDS 펩타이드를 결합시킨 키토산막에서 요오드가 검출되었으며 펩타이드를 부착하지 않은 대조군에서는 검출되지 않았다. 따라서 cross-linker를 이용한 펩타이드와 키토산막의 공유결합을 확인할 수 있었다. 세포 배양 후 1일째 부착된 세포 수를 측정한 결과 0.1mg/ml 이상의 GRGDS 펩타이드 농도로 공유 결합시킨 키토산막에서 부착 세포 수가 다른 농도에 비해 유의성 있게 많이 관찰되었다. 이 농도 이하에서는 대조군과 실험군간에 세포부착의 유의한 차이가 없었다. 따라서 주사전자현미경을 이용한 부착 세포의 양상에 관한 관찰은 0.1mg/ml 농도의 펩타이드를 이용하였다. 세포 배양 7일째, 부착된 세포 수 측정 결과 GRGDS의 농도에 따른 유의성 있는 차이가 없었으며, 실험군과 대조군간에도 유의성 있는 차이가 없었다. 주사전자현미경 관찰결과 2시간 및 24시간 배양된 실험군 모두에서 별모양의 세포들이 키토산막 표면에 편평하게 잘 부착되어 있으며 많은 위족이 발달된 소견을 보인 반면, 대조군에서는 원형 또는 다각형 모양의 세포들이 실험군에 비해 부착이 덜 되어있는 양상을 보였다. 이 연구를 통하여 기능성 펩타이드를 생체재료의 표면에 공유결합 시키는 방법을 확립할 수 있었으며, RGD 펩타이드의 공유결합으로 표면개질된 키토산막이 조골세포의 부착능을 증진시킬 수 있음을 확인하였다. 표면개질된 생체재료를 소, 중동물에 적용시켜 생체 내에서의 생물학적 영향을 평가할 필요가 있으며, 이 실험의 결과는 향후 다양한 기능성 부착분자를 선발, 고안하여 임플란트용 생체재료의 표면개질에 이용하는 이른바 모방생체재료분야에 널리 활용될 수 있을 것으로 생각된다.