• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2000년도 학술대회논문집
• /
• pp.25-29
• /
• 2000

Nowadays, natural resource are running out and the level of the environment contamination is getting serious. To solve these problems, each country and institute tend to need many-sided researchs and developments. At this point, especially, there are many coal-mines in Jung-sun and Tae-back where are located in Kangwon province. By the way the abandoned mines cause not only local economy collapse but also environment contamination by submergence of stony mountains. The counterplan is positively inquired further examination by the government. Consequently, we hope that the recycle of polymer concrete can reduce the environment contamination, suggest the new direction of Green Design and can be switched over high added value goods. In conclusion, the recycle of polymer concrete will be valuable.

• 한국농공학회지
• /
• 제45권1호
• /
• pp.45-54
• /
• 2003

The effects of binder content and silica sand content on the durability characteristics of lightweight polymer concretes are examined. As a result, the flame lingering times using unsaturated polyester resin and non-combustible polyester resin were 60∼120 and 0∼4 seconds respectively, and the combustion lengths were 9∼11 mm and 0∼3 mm, respectively. Thus it is believed that the lightweight polymer concrete was incombustible and the light weight polymer concrete in which non-combustible material was added was perfectly non-combustible. The percent of original mass of lightweight polymer concrete, according to the freezing-thawing experiment, was below 0.3 %, which was much less than that of cement concrete. The pluse velocity, for the case of the binder content 28 %, showed the minimum decreasing rate for the lightweight polymer concrete with silica sand content of 50 %. The higher the binder content, the greater the durability. That is much higher than other material and believed that the freezing-thawing was suppressed by a low absorption.

• 한국농공학회논문집
• /
• 제46권6호
• /
• pp.37-45
• /
• 2004

In this study, twelve different glass fiber reinforced polymer concrete composite panel specimens with various rib heights and tensile side and reinforced side thickness were produced, and the flexural tests were conducted to figure out the effect of The height and thickness influencing on the flexural properties of composite panel. Test results of the study are presented. Especially, a prediction equation of the ultimate moment based on the strength design method agrees well with the test results, and it is thought to be useful for the corresponding design of cross-section according to various spans as the glass fiber reinforced polymer concrete composite panel is applied for a permanent mold.

• 한국농공학회논문집
• /
• 제50권5호
• /
• pp.29-37
• /
• 2008

Stress-strain relation and stress block parameters of polymer concrete flexural compression members were experimentally investigated. For these purposes, a series of C-shaped polymer concrete specimens subjected to axial compressive load was tested. Based on the test results, we proposed an equation by which the stress-strain relation of polymer concrete can be predicted. In this model, we took account the slope of descending branch beyond the peak stress point of single curve. The proposed equation was numerically integrated to compute the rectangular stress block parameters. Computed ${\beta}_1$ was greater than the values prescribed in ACI 318 Code for cement concrete, and $\gamma$ was about 0.85 that is similar to the value regulated in the ACI.

• 한국농공학회논문집
• /
• 제50권5호
• /
• pp.51-60
• /
• 2008

This study is to relate the bond characteristics of CFRP rebar in high strength concrete incorporated with silica fume(SF) and metakaolin(MK). An direct bond test were performed to evaluate the effect of SF and MK on bond properties of high-strength concrete and CFRP rebar. The high strength concrete mix included four SF and MK mixes with 0%, 5%, 10% and 15%. Results of bond performance experiment in relation to pullout vs slip behavior of FRP rebar and high strength showed better performance of SF than MK. Also, the results showed the improved bond strength as replacement ratio of SF and MK increased. The relative bond strength in which $1.3{\sim}3.2$ of estimated values were obtained.

• 한국농공학회논문집
• /
• 제47권6호
• /
• pp.27-34
• /
• 2005

The purpose of this study is to improve the durability performance of polymer modified cement composites for repair of concrete under combined aging conditions. The experimental procedure was divided into three parts. First, the replacement level of mineral admixtures in polymer modified cement composites were determined in an experimental study based on a Box Behnken design. Second, the flow value, compressive strength and chloride permeability test of sixteen types of mixtures were conducted. Test results show that the polymer modified cement composites were effected on the improvement of the compressive strength and permeability performance. Third, the effects on the replacement level of silica fume mixture was evaluated by the compressive strength, chloride permeability, chemical resistance and repeated freezing and thawing cycles test. They demonstrated that the polymer modified cement composites using mixture of silica fume, fly ash, and blast furnace slag improved the durability performance.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2000년도 학술발표회 발표논문집
• /
• pp.272-277
• /
• 2000

This study is performed to evaluate the engineering properties of permeable polymer concrete with blast furnace slag and fly ash. The following conclusions are drawn; 1. The highest strength is achieved by 50% filled blast furnace slag powder and fly ash permeable polymer concrete, it is increased 36% by compressive strength, 119% by tensile strength and 217% by bending strength than that of the normal cement concrete, respectively. 2. The ultrasonic pulse velocity is in the range of 2,022 ∼ 2,139m/s. The highest pulse velocity is showed by 50% filled blast furnace slag powder and fly ash permeable polymer concrete. 3. The water permeability is in the range of 4.612∼5.913$\ell$/$\textrm{cm}^2$/h, and it is largely dependent upon the mix design.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.1014-1020
• /
• 2004

In this study, durability of the nano-level inorganic polymer based coatings which can provide a barrier against the ingress of moisture or aggressive ions to concrete is discussed. For the durability evaluation of the coatings, chloride penetration test, accelerating carbonation test, freezing and thawing test, and sulfate ponding test are conducted. As the result of this study, concrete applied nano-level inorganic polymer based coatings has a much higher resistance to the ingress of chloride ion, carbon dioxide, moisture and aggressive acid than plain concrete and epoxy resin based paint by means of crosslinking three-dimensional structure with concrete structure.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 춘계 학술논문 발표대회
• /
• pp.236-237
• /
• 2015

Concrete is the one of the most widely used in every country as a structural materials. On the other hand, a lot of fire incident has been occurred all over the world. But maintenance methods such as inspection and diagnostic methods, design methods, quality control methods for the purpose of improving the performance of concrete structures damaged by fire has made in its own way. Therefore, the purpose of this proposal of new working item is is to ensure the safety of the concrete structures damaged by fire in the field of assessment of damage, design, repair methods and so on through the International Organization for Standardization.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 추계 학술논문 발표대회
• /
• pp.19-20
• /
• 2014

This study is to find out the tensile strength and bonding strength of VAE powder as a preliminary study for the application of the powder to the high strength concrete. The result of the study showed that the compressive strength decreases when more polymers is put into the concrete. On the other hand, it showed that the tensile strength and the bonding strength get improved when the more polymers are put into the concrete. Especially in case of the mixture for high strength concrete, it was found out that more strength is produced than the ordinary concrete.