• 한국가스학회지
• /
• 제17권2호
• /
• pp.44-49
• /
• 2013

천연가스의 사용량이 날로 증가됨에 따라 고용량의 가스를 운송하기 위해 고압배관의 설치 운영이 불가피하고 이에 따라 고압의 매몰 천연가스배관에서 다양한 원인에 의한 결함 발생 시 대규모 누출로 이어지면 높은 압력의 가스 방출에 따른 대기 중 확산 그리고 점화원에 의한 화재 폭발로 인하여 큰 피해가 발생할 수 있다. 이 연구에서는 고압의 매몰 천연가스배관에서 결함 발생 시 매몰된 배관에서의 가스 누출 거동 분석과 가스 확산 및 지연점화에 따른 플래시 화재의 피해 거리를 예측하여, 사고 영향을 감소할 수 있도록 대피거리의 산정 등에 의한 비상조치계획을 세워 안전관리 활동에 도움이 되고자 한다.

• 한국전산유체공학회지
• /
• 제17권3호
• /
• pp.99-107
• /
• 2012

In this paper, the shock waves in compressible solids and liquids are simulated using a six-equation diffuse interface multiphase flow model that is extended to the Cochran and Chan equation of state. A pressure relaxation method based on a volume fraction function and a pressure-correction equation are newly implemented to the six-equation model. The developed code has been validated by a shock tube problem with liquid nitromethane and an impact problem of a copper plate on a solid explosive. In addition, a new problem, an impact of a copper plate on liquid nitromethane, has been solved. The present code well shows the wave structures in compressible solids and liquids without any numerical oscillations and overshoots. After the impact of a solid copper plate on liquid, two shock waves (one propagates into liquid and the other into solid) are generated and a material interface moves to the impacting direction. The computational results show that the shock velocity inside the liquid linearly increases with the impact velocity.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.220-223
• /
• 2008

A test facility to measure the performance of a KM(Kick Motor) is constructed, and prediction of blast wave propagation over the facility is performed to check if the safety of test personnel in MCC(Main Control Center) can be guaranteed even for the most severe explosion. Assuming that the initial explosion energy is contained in a sphere under the pressure of 500, 1000, 1500 psi, respectively, the radius of the sphere is determined for each pressure to set the mass of contained explosion gas to 35 kg. The material properties of explosion gas are set to be the ones of KM propellant combustion gas under normal condition. To reduce the effort and time required for a complex three-dimensional modeling, the flowfield is approximated to axismmetry. Calculations are performed for all three initial pressure conditions, and the analysis of the result is given for 1500 psi which is expected to be the worst case. The maximum pressure is 3.5 psig while the minimum pressure is -1.2 psig on the outer wall of MCC, and the maximum pressure difference between the inner and outer walls of protection wall amounts to 3.0 psi.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.25-30
• /
• 2000

Residual stresses induced in U-bending and tube-to-tubesheet joining processes of PWR's steam generator row-1 tube were measured by X-ray method and Hole-Drilling Method(HDM). The stresses resulting from the Internal pressure and the temperature gradient in the steam generator were also estimated theoretically. In U-bent lesions, the residual stresses at extrados were induced with compressive stress(-), and its maximum value reached -319 MPa in axial direction at ${\psi}=0^{\circ}$ in position. Maximum tensile residual stress of 170MPa was found to be at the flank side at Position of${\psi}=90^{\circ}$, i.e., at apex region. In tube-to-tubesheet fouling methods, the residual stresses induced by the explosive joint method were found to be lower than that by the mechanical roll method. The gradient of residual stress along the expanded tube was highest at the. transition region, and the residual stress in circumferential direction was found to be higher than the residual stress in axial direction. Hoop stress due to an internal pressure between primary and secondary side was analyzed to be 76 MPa and thermal stress was 45 MPa.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1998년도 춘계 학술대회논문집
• /
• pp.1-14
• /
• 1998

Underwater explosion properties for TNT, an ideal explosive, and DXD-04, a nonideal explosive, were numerically modeled with a one-dimensional Lagrangian hydrodynamic code. The equation of state parameters for detonation products for TNT and DXD-04 were obtained from the BKW code, assuming complete reaction. Burn of TNT was modeled by using the Chapman-Jouguet(CJ) volume burn technique, a programmed-burn technique, assuming instantaneous detonation reaction. Burn of DXD-04 was modeled by using the same technique and by using the reaction rate calibrated from two-dimensional steady-state detonation experiments. The calculations for TNT reproduced the experimental peak pressure of the shock wave propagating through water with an error of $3.0\%$ and the experimental oscillation period of the bubble formed of detonation products with an error of $2.3\%$. For DXD-04, the CJ volume burn technique could not reproduce the experimental observations. When the reaction rate calibrated from two-dimensional steady-state detonation experimental data, the calculated peak pressure was slightly higher by $7.3\%$ than the experimental data, but the calculated shock profile was in good agreement. The bubble period was reproduced with an error of $1.8\%$. These results demonstrated that underwater explosion properties for an ideal explosive can be predicted by using a programmed burn technique, and that, however, those for a nonideal explosive can be predicted only when a well-calibrated reaction rate is used.

• 전력전자학회논문지
• /
• 제15권1호
• /
• pp.17-26
• /
• 2010

본 논문은 군용 공중폭발탄에 사용하는 발진기의 에러를 최소화 하고, 그 효율을 극대화하기 위하여 시뮬레이션과 매우 유사한 형태의 통계적 모델링 방법을 제안한다. 제안된 방법은 일정하고 안정된 출력을 내는 실제 모델에서 실험 계획에 의하여 얻은 데이터로부터 통계적인 해석을 통하여 새로운 형태의 방정식을 구하였다. 그리고 그것을 바탕으로 각각의 전자 부품들을 출력과 일치되도록 모델링 한 후, 출력 예측이 가능한 시뮬레이션을 수행하고, 실제 모델의 출력 데이터와 비교하여 그 유용성, 정확도 및 정밀도를 입증하였다.

• 한국CDE학회논문집
• /
• 제18권6호
• /
• pp.461-469
• /
• 2013

Computer simulation with FEM is very useful to analyze hypervelocity impact phenomena that are tremendously expensive or otherwise too impractical to analyze experimentally. Shock physics can be efficiently handled by mesh adaptation which allows finite element mesh to be locally optimized to resolve moving shock wave in explosion. In this paper, an adaptive meshing technique based upon quadtree data structure was applied to resolve ballistic impact phenomena. The technique can adaptively refine a mesh in the neighborhood of a shock and coarsen the mesh for the smooth flow behind the shock according to a criterion. The criterion for refinement and coarsening is based upon the standard deviation of the gradient of shock pressure on the associated field. Shock simulation starts with the rough mesh of the pressure field and mesh density is increased locally under the criterion at each time step. The results show that the mesh adaptation enables to minimize the global computation error of FEM and to increase storage and computational saving compared to the fixed resolution of the conventional static mesh approach.

• 한국정보통신학회논문지
• /
• 제18권12호
• /
• pp.3069-3078
• /
• 2014

본 연구에서는 다양한 수중무기폭발 체계 중 대표적인 비닉(庇匿) 무기체계인 기뢰를 중심으로 공격형 부설에 의한 억제 시 적함 탐지의 핵심이 될 자력계를 신규 Modeling & Simulation에 의해 성능 개선의 효과를 사전 검증한다. 또한, 신규 3축 자력계를 설계/제작/실험을 진행한 결과를 다룬다. 신규 자력계를 새로운 신형 수중무기체계에 적용하기 위해 상용 전자기장 수치해석 도구를 이용해 잠수함을 모델링하여 실 함정의 자기장특성을 예측한다. 실험의 마지막 단계로 축소 모형을 제작하여 실제 해상시험을 하지 않더라도 육상에서 성능검증 할 수 있는 방법을 제시한다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.217-225
• /
• 2010

격벽 착화 모듈은 도우너 화약이 폭발하면서 발생한 충격파가 격벽을 통해 억셉터 화약에 전달되었을 때 동작한다. 격벽 착화 모듈의 가장 중요한 설계 요소인 격벽의 최소 두께를 결정하기 위하여 구조해석을 수행한 결과 격벽의 두께가 0.1 mm 이상인 경우 구조적으로 충분한 마진이 있음을 확인하였다. 격벽의 적정 두께를 결정하기 위하여 VISAR 간섭계를 이용하여 억셉터 화약 충전면에서 자유 표면 속도를 계측하였다. 이 속도를 이용하여 충격 압력으로 환산하고 그 결과를 억셉터 화약의 반응 민감도와 비교함으로서 격벽 두께에 따른 격벽 착화 모듈의 작동 신뢰도를 계산하였다.

• 한국안전학회지
• /
• 제3권2호
• /
• pp.5-16
• /
• 1988

This study is conducted to evaluate the explosion of tolune storage tank in the petrochemical plant by Fault Tree Analysis. The conclusions are as follows; 1) Fault Tree diagram and the required computer program for evaluation of explosion accident is developed. 2) The probability of the top event, explosion accident, is $1.5\;{\times}\;10^{-8}$ per year, so there is almost no possibility of explosion during the life cycle of tank. However, the probability of Gate 6 and Gate 7 is 8.8 per month, therefore, attention should be paid to them for accident prevention. 3) The number of minimal cut sets is 67 sets which are not calculated the probability of each set, because of the lack of computer capacity. All the minimal cut sets should be examined case by case. However, it is necessary to be paid attention to COM1, 126, 131, and COM4 in minimal cut sets, because the number of appearance is so high. 4) The number path sets is 70 sets which are not calculated the probability of each set, because of the lack of computer capacity. It is very useful to prepare safety checklist by using this minimal path sets. Also, the events which appear many times, 123, COM5, 139, 127 and 128, are very high in reliability.