• 한국도로학회지:도로
• /
• v.5 no.4 s.18
• /
• pp.36-46
• /
• 2003

포장구조체에서 요구되는 강도를 갖게 하는 구조 설계의 방법은 경험적 절차부터 반역학적 절차까지 발전되어 왔다. 재생 가열아스팔트혼합물이 기존의 가열아스팔트혼합물(HMA)과 비교하여 비슷하거나 때에 따라 더 좋은 성능을 가져오므로, AASHTO설계지침서에서는 본질적으로 재생(recycled) HMA 재료와 신생(virgin) HMA 재료간의 차이가 없다고 기술하고 있으며, 기존 HMA 재료에 사용되는 덧씌우기설계법의 구조회복 분석방법(structural rehabilitation analysis method)을 재생포장설계에도 권장하고 있다. 재생 가열아스팔트의 설계를 위한 AASHTO 방법은 설계교통량, 교통량 및 수행능력예측의 신뢰수준, 공용기간, 그리고 포장상태 평가지수에 의하여 결정된 포장구조체에서 요구되는 포장두께지수(SN)에 기초한다. 포장두께지수(SN)는 포장층 두께, 상대강도계수, 각 층의 배수조건들의 곱의 조합으로서 나타내어질 수 있다. 덧씌우기로 간주될 수 있는 재생된 층의 포장두께지수(SN)는 기존 포장에서의 포장두께지수와 보강된 포장에서 요구되는 포장두께지수의 차이에 의하여 계산되어질 수 있다. 상대강도계수의 값은 AASHTO 설계지침에 명시되어 있다. AI 방법은 교통량, 노상의 회복탄성계수, 그리고 설계두께를 계산하기 위한 표층과 기층의 종류를 사용한다. 이 방법은 재생된 가열혼합물질과 기존의 가열혼합물질과는 거의 비슷한 성능을 나타낸다고 본다. 또다른 AI 방법에 의하면 재생된 층은 덧씌우기층이라고 간주하고, 현재의 포장두께와 요구되어지는 포장두께 사이의 차를 이용하여 재생될 층의 두께를 산정한다. 소요되는 덧씌우기 두께는 포장의 현장 상태지수(condition rating)와 각 종류에 따른 포장체와 포장재료가 아스팔트 콘크리트층의 등가두께로 전환되어 나타나는 방법에 근거하여 결정될 수 있다. 또 다른 방법은 포장체 각 층의 물성과 하중을 이용한 컴퓨터 프로그램에 의하여 산정된 하중-변형 응답에 의한 설계 방법을 포함한다. 이런 방법들에서는 포장체는 탄성이나 점탄성층 위에서 탄성이나 점탄성 거동을 보인다고 가정한다. 재생 상온혼합물에서의 AASHTO 설계 방법은 가열혼합물의 설계방법과 유사하다. 그러나, 재생 상온혼합물에서의 상대강도계수는 시공방법에 좌우되므로, 기술자의 판단을 근거로 하여 결정되어져야 한다. AI방법에서는 포장구조체를 다층탄성구조라고 보고, 노상의 강도와 설계 교통량을 근거로 요구되는 포장두께를 결정한다. 재생 상온혼합물 기층의 두께는 재생 상온혼합물 기충 위에서 가열아스팔혼합물에 대하여 산정된 덧씌우기 두께를 이용하여 결정할 수 있다. 아스팔트 표면의 재생은 기존 포장의 구조적 능력을 정상적으로 개선할 수 없으므로, 표면 재생의 두께를 설계하는 방법은 없다. 그러나, 임의의 덧씌우기 두께는 기존의 덧씌우기 설계법에 기초하여 산정 할 수 있다. 만약 덧씌우기가 승차감만을 개선시킨다고 여겨진다면, 혼합물에서 사용되어지는 최대 골재 크기에 기초한 최소 두께를 결정할 수 있다.

• 한국방재학회:학술대회논문집
• /
• 2010.02a
• /
• pp.47.2-47.2
• /
• 2010

빗물을 노상 침투시키는 투수성포장은 물순환 보전과 차량 주행 안전성 확보와 같은 효과를 기대할 수 있다. 지금까지 보도나 주차장 같이 비교적 교통조건이 열악하지 않은 구간에 적용되고 있지만 우수 침투로 인해 노상이 연약화 될 것을 우려하여 현재까지 차도에 적용하지 못하고 있으며 설계 방법 또한 정립되어 있지 못한 실정이다. 본 연구에서는 투수성포장의 포장단면을 설계하기 위한 방안으로 단지내 포장을 투수성포장으로 설계할 경 물의 침투로 인해 노상의 지지력이 약화 된다고 가정하고 노상 지지력의 약화에 따른 포장층의 역학적 거동 특성을 유한요소 해석을 통하여 분석하여 구조적 안정성을 확보할 수 있는 포장두께를 분석하였다. 또한 설계 개념에서 노상의 지지력 저하에 따른 포장두께의 할증방안과 할증두께를 분석하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.4
• /
• pp.537-548
• /
• 2022

It is important to design the pavement thickness considering heavy-duty traffic loads, which can cause excessive stress and strain in the pavement. Port-rear roads and industrial roads have many problems due to early stress in pavement because these have a higher ratio of heavy loads than general roads such as national roads and expressways. Internationally, composite pavement has been widely applied in pavement designs in heavy-duty areas. Composite pavement is established as an economic pavement type that can increase the design life by nearly double compared to that of existing pavement while also decreasing maintenance and user costs. This study suggests a thickness design method for composite pavement using roller-compacted concrete as a base material to ensure long-term serviceability in heavy-duty areas such as port-rear roads and industrial roads. A three-dimensional finite element analysis was conducted to investigate the mechanical behavior and the long-term pavement performance ultimately to suggest a thickness design method that considers changes in the material properties of the roller-compacted concrete (RCC) base layer. In addition, this study presents a user-friendly catalog design method for RCC-base composite pavement considering the concept of linear damage accumulation for each container trailer depending on the season.

• International Journal of Highway Engineering
• /
• v.7 no.2 s.24
• /
• pp.23-31
• /
• 2005

This study is a part of research for developing the technologies of long life pavements having more than 40-year design life. The objective of this study is to develop the simplified design procedure for determining the layer thickness and modulus of the long life pavement. A synthetic database was established using the finite element program of a pavement structure with various combinations of layer thickness and modulus. The synthetic database includes the structural and material information, surface deflection, and critical pavement responses. Using the developed synthetic database, this paper suggests the minimum layer thickness and modulus for long life pavements bared on the limited strain level concept. Results demonstrate that the pavement greater than 410mm of total AC layer thickness is considered as the long life pavements regardless of the material characteristics and thickness in each layer. To become a long life pavement, a total thickness of AC layer should be greater than 250mm. The design procedure for determining the layer thickness and modulus of the pavements with AC layer thickness ranging from 250 to 410mm is also presented in this paper.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.6
• /
• pp.46-54
• /
• 2015

Base on Korean design code, previous design code had not considered the effect of pavement on the orthotropic steel deck, however recent design code (Limit State Design Method, 2012) allowed to consider the effect of pavement on the orthotropic steel deck, and efforts to apply the stiffness of pavement to the deck continue. Meanwhile, research on the effect of ultra thin bridge deck overlay on the orthotropic steel deck is inadequate, previous study was limited in about fatigue stress and performance between pavement layer and the orthotropic steel deck. In this study, according to changing of pavement layer stiffness application, pavement materials, pavement thickness and steel deck thickness, analysis of deflection. In addition to base on this result, consider effectiveness of ultra-thin pavement stiffness application on the orthotropic steel deck.

• International Journal of Highway Engineering
• /
• v.13 no.3
• /
• pp.39-49
• /
• 2011

The porous pavement system is widely considered very effective in urban street because of its various benefits on safety and environment, but the pavement thickness design system has not been established yet. In porous pavement system. rainwater penetrates to the subgrade through porous pavements layers. Porous pavements are expected to reduce or alleviate the problems caused by impermeable pavement layer such as flood damage due to heavy rain in the city, drainage load, disorder in ecosystem, and heat island. However, its structural design methods in traffic roads has not been made mainly because of not being able to consider adequately the effect of rainwater on subgrade strength. In this study, structural design method of porous pavements is suggested after considering the subgrade weakness due to rainwater and numerical mechanical analysis. It is noted that elastic modulus of subgrade is reduced by 20% as subgrade moisture content is increased by 2% at optimum moisture content in the literature review. As a result of both finite element analysis and strength loss of subgrade by the existing design method, it is necessary to increase subbase thickness about 30cm in porous pavements compared with the existing traffic road pavement system. It is similar to premium thickness of structural design of porous pavements in Japan.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.1
• /
• pp.113-119
• /
• 2018

An extensive effort is actively being made to implement permeable pavement systems in urban or residential areas of South Korea in order to achieve efficient water circulation system based on low impact development (LID) design concept. This study aims to establish the design factors and procedure for permeable asphalt pavements structural design. Based on the review of previous studies, the 1993 AASHTO design method is found to be adequate for permeable pavements structural design. In this study, the design program based on 1993 AASHTO design procedure in conjunction with domestic roadway design standards was developed to accommodate the characteristics of permeable asphalt pavements. Primary design parameters such as structural layer coefficients of permeable materials were successfully quantified based on literature reviews and parallel analyses. Comparable design thicknesses were obtained between the developed permeable pavement design (PPD) program and Korea pavement research program (KPRP) under different levels of traffic and subgrade load bearing capacity.

• International Journal of Highway Engineering
• /
• v.11 no.4
• /
• pp.107-115
• /
• 2009

This study was conducted to investigate the effect of the slab thickness on the tensioning design and to determine the optimal slab thickness of the post-tensioned concrete pavement (PTCP). The tensile stresses due to the vehicle and environmental loads were obtained using a finite element analysis model and the tensioning stress was calculated employing an allowable flexural strength. The environmental loads of both the constant temperature gradient and the constant temperature difference between top and bottom of the slab were considered. The tensioning designs for various slab thicknesses were performed considering prestressing losses. The comparison results showed that generally as the thickness increased, the number of tendons became larger. Consequently, the design was not economical for a thicker slab thickness. Even though the number of tendons became smaller with an increase in the thickness under the small environmental load, a thicker PTCP slab was not economical because of a higher cost of concrete than that of steel. Therefore, the slab thickness should be kept in minimum within the construction available thicknesses.

• 한국도로학회지:도로
• /
• v.3 no.3 s.9
• /
• pp.50-55
• /
• 2001

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.487-493
• /
• 2017

The main purpose of this study is to evaluate the main parameters involved in the asphalt pavement distresses, including IRI (International Rough Index), fatigue, and permanent deformation. The main parameters are the region (Seoul and Busan), traffic level, asphalt binder, maximum aggregate of surface course, thickness of the surface course and base. A total of 64 case studies were carried out under the auspices of the KPRP (Korea Pavement Research Program). From the analysis of the KPRP test results, the key factors for the asphalt pavement distress were determined. Considering the effect of one variable in the basic condition, asphalt binder was the major factor having an effect on the distresses for an AADT (Annual Average Daily Traffic) of 5000 in the Seoul area. Among the remaining factors, the results were found to be in the order of the base layer thickness (A), surface layer thickness (B), and aggregate particle size thickness (D). The same results were obtained for an AADT of 10000. In the case of Busan with an AADT of 5000, the same result was obtained as for Seoul. Among the remaining factors, the results were in the order of the base layer thickness (A), aggregate particle thickness (D), and surface layer thickness (B). Even though there was a slight difference in the effect of the traffic level and region, asphalt binder was the parameter having the greatest effect on the asphalt pavement distress. In the case where the effect of multiple parameters was analyzed, the combination of the asphalt binder and base thickness showed a relatively strong effect.