• Journal of the Korean association of regional geographers
• /
• v.22 no.4
• /
• pp.887-911
• /
• 2016

The empirical law that transverse dunes migrate inversely with their heights leads logically to the prediction that multiple dune ridges will converse to a single huge dune by merging. This contradicts the existence of the steady state dune fields on the Earth. The recent studies have emphasized dune collisions as a key mechanism to the stability of dunefield. The roles of wind shadow aspect ratio, however, have yet to be fully explored. This research aims to investigate the potential roles of wind shadow aspect ratio in the dynamical behaviors of transverse dune field. The simplified model is established for this, based upon allometric properties of transverse dunes, wind speedup on the stoss slope and sand trapping efficiency. The derived governing equations can be transformed to the zoning criteria and vector field for dune evolution. The dynamics analysis indicates that wind shadow aspect ratios do not produce convergent areas on the behavior space; rather, they just act as one of the factors that affect the trajectories of dune evolution. Though the model cannot represent the stability of dune field, but seem to produce a reasonable exponent for dune spacing-height relations.

• Journal of Korean Society of Transportation
• /
• v.31 no.1
• /
• pp.47-56
• /
• 2013

The present study proposed a methodology to analyze the networking efficiency of arterial road networks. The methodology was motivated to design three-dimensional networks and to analyze the networking ability quantitatively, which is a novel approach compared to existing methods depending on the two-dimensional network definition and the qualitative analysis for improving arterial road networks. The method considered the interdependence between high-level freeways and low-level highways, the ITS-based information for traffic and road conditions, and the physical networking. These three factors were quantified by a networking index (NI), and the networking efficiency was measured by a networking rate (NR). The present study proved that the networking efficiency (NR) was influenced by travel information sharing (i.e., ITS) and physical factors. This supports the fact that the integrated improvements of physical and ITS factors are necessary for an arterial road. The proposed method was applied for an actual arterial road network. It was found that the nation-wide NR was higher than that for the metropolitan area, which might be due to the difficulty in switching between high- and low-level networks and the lack of ITS functions in the metropolitan area.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.33 no.4
• /
• pp.231-244
• /
• 2015

The accuracy of reference point of VLBI antenna is mandatory to perform collocation of different space geodetic techniques. In this study, we evaluated the optimal methods for the 3D circle fitting to enhance the accuracy of the reference point of VLBI antenna. Two kinds of methodologies for the orthonormal coordinate system with translation of planar observation point and the unitary coordinate transforamation were suggested and their fitting accuracies were evaluated where the orthogonal distance was calculated by residual between observation point and fitting model and the recursive calculation was performed to improve the accuracy of 3D circle fitting. Finally, we found that the methodology for the unitary coordinate transformation is highly appropriate to determine the optimal equation for azimuth-axis and elevation-axis of VLBI antenna. Therefore, the reference point of VLBI antenna with high accuracy can be determined by the intersection of the above two axises (azimuth-axis and elevation-axis). This result is expected to be utilized for a variety of researches for connection between VLBI observation results and the national control point.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.34 no.6
• /
• pp.643-651
• /
• 2001

Paddlewheel-driven circulation in a culture pond has been simulated based on the depth integrated 2 dimensional hydrodynamic model. Acceleration by paddlewheel is expressed as shaft force divided by water mass discharged by paddlewheel blades. The model has been calibrated and applied to culture ponds as following steps:- i) The model predicted velocities at every 10 m along longitudinal direction from the paddlewheel. The model was calibrated comparing the results with the measured values at mass correction factor $\alpha$ and dimensionless eddy viscosity constant $\gamma$, respectively, in a range $15\~20$ and 6. ii) Wind shear stress was simulated under conditions of direction $0^{\circ}C,\;90^{\circ}C\;and\;180^{\circ}C$ and speed 0.0, 2.5, 5.0 and 7.5 m/s. Change rate of current speed was <$1\%$ at wind in parallel or opposite direction to the paddlewheel-driven jet flow, while $4\%$ at orthogonal angle. iii) The model was then applied to 2 culture ponds located at the Western coast of Korea. The measured and predicted currents for the ponds were compared using the regression analysis. Analysis of flow direction and speed showed correlation coefficients 0.8928 and 0.6782 in pond A, 0.8539 and 0.7071 in pond B, respectively. Hence, the model is concluded to accurately predict circulation driven by paddlewheel such that it can be a useful tool to provide pond management strategy relating to paddlewheel operation and water quality.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.7
• /
• pp.667-678
• /
• 2002

In this paper, a new radiating structure with a multi-layered two-dimensional metallic disk array was proposed for shaping the flat-topped element pattern. It is an infinite periodic planar array structure with metallic disks finitely stacked above the radiating circular waveguide apertures. The theoretical analysis was in detail performed using rigid full-wave analysis, and was based on modal representations for the fields in the partial regions of the array structure and for the currents on the metallic disks. The final system of linear algebraic equations was derived using the orthogonal property of vector wave functions, mode-matching method, boundary conditions and Galerkin's method, and also their unknown modal coefficients needed for calculation of the array characteristics were determined by Gauss elimination method. The application of the algorithm was demonstrated in an array design for shaping the flat-topped element patterns of $\pm$20$^{\circ}$ beam width in Ka-band. The optimal design parameters normalized by a wavelength for general applications are presented, which are obtained through optimization process on the basis of simulation and design experience. A Ka-band experimental breadboard with symmetric nineteen elements was fabricated to compare simulation results with experimental results. The metallic disks array structure stacked above the radiating circular waveguide apertures was realized using ion-beam deposition method on thin polymer films. It was shown that the calculated and measured element patterns of the breadboard were in very close agreement within the beam scanning range. The result analysis for side lobe and grating lobe was done, and also a blindness phenomenon was discussed, which may cause by multi-layered metallic disk structure at the broadside. Input VSWR of the breadboard was less than 1.14, and its gains measured at 29.0 GHz. 29.5 GHz and 30 GHz were 10.2 dB, 10.0 dB and 10.7 dB, respectively. The experimental and simulation results showed that the proposed multi-layered metallic disk array structure could shape the efficient flat-topped element pattern.