• Smart Media Journal
• /
• v.9 no.4
• /
• pp.176-186
• /
• 2020

The size and shape of crops are diverse, and the growing environment is also different. Therefore, when one uses a drone to spray pesticides, the characteristics of each crop must be considered, and flight conditions such as the flight height and forwarding velocity of the drone should be changed. The droplet flow of pesticides is affected by various flight conditions, and a large change occurs in the sprayed area. As a result, an uneven distribution of liquid may be formed at the wake, and the transport efficiency will be decreased as well as there would be a risk of toxic scatter. Therefore, this paper analyzes the degree of distribution of pesticides to the crops through numerical analysis when pesticide is sprayed onto the selected three crops with different characteristics by using agricultural drones with different flight conditions. On the purpose of establishing a guideline for spraying pesticides using a drone in accordance with the characteristics of crops, this paper compares the amount of pesticides distributed in the crops at the wake of nozzle flow using the figure of merit, and the sum of transported liquid rate divided by the root mean square of the probability density function.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.1
• /
• pp.29-36
• /
• 2008

Spray characteristics for APU gas turbine engine are investigated. In the test, four flight conditions such as sea level idle, sea level max power, 20,000 feet idle, 20,000 feet max power are used as spray experimental conditions. Spray visualization was performed by using ND-YAG laser bean PDPA(Phase Doppler Particle Analyzer) was used for measuring the particle diameter and velocity from 20 mm to 100 mm from discharge orifice. From the test result, SMD is $90{\sim}95\;{\mu}m$ 맛 20,000 ft idle condition and SMD is $60{\sim}75\;{\mu}m$ at sea level idle condition. Also SMD is $55{\sim}65\;{\mu}m$ at 20,000 ft max power condition and SMD is $30{\sim}70\;{\mu}m$ at sea level max power condition. In the case of 20,000 ft idle condition, combustion instability could be occurred due to the higher drop diameter. Therefore it is necessary to decrease the droplet diameter in the high altitude condition.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.5
• /
• pp.510-519
• /
• 2013

In this study, the spray characteristics of a pressure swirl atomizer classified into a liquid sheet-type swirl nozzle for Urea-SCR system were investigated experimentally with the variation of injection pressure. The length to diameter ratio ($l_o/d$) of the nozzle was 3.1, and the swirler was set inside the nozzle tip to give injecting fluid angular momentum. The injection duration of the nozzle was controlled by PWM (pulse width modulation) modes. The development processes of the spray were imaged by a 2-D PIV system, and the change of spray angle was measured. The atomization characteristics, including axial velocity and SMD, were measured using a 2-D PDA system with the injection pressures at room temperature and ambient pressure conditions. As the experimental results, the injection pressure had a significant impact on the spray structure showing a different shape around the spray leading edge, and the smaller SMD was observed with increasing injection pressures, which was similar to that of the previous work.

• Korean Journal of Materials Research
• /
• v.10 no.3
• /
• pp.204-211
• /
• 2000

The $(Y,Gd)BO_3:Eu$ red phosphors for PDP application were synthesized by ultrasonic spray method and then their photoluminance properties were investigated under 147nm VUV irradiation. The precursor solution of acetates of Y, GD and Eu and boric acid diluted in water was sprayed using 1.7 MHz ultra-sonic sprayer into the reaction tube held at high temperature. The as-sprayed particles were amorphous phase having C-C and C-H bonds due to the insufficient thermal reaction during the pass along the tube. But the sprayed samples followed by heat treatment at $1100^{\circ}C$ had the same crystal structure and chemical composition as those samples followed by solid state reaction. It was found that the $(Y_{0.7}Gd_{0.3})_{0.95} BO_3:Eu_{0.05}^{3+}$ phosphor particles synthesized by spray at $500^{\circ}C$ and then heat treated at $900^{\circ}C$ had a spherical-like shape and fine particle size at $0.7{\mu\textrm{m}}$ having a narrow size distribution, while the phosphor particles made by solid state reaction was $3{\mu\textrm{m}}$ coarse and non-uniform size distribution. The emitting intensity under 147nm VUV excitation for $(Y_{0.7}Gd_{0.3})_{0.95}BO_3:Eu_{0.05}^{3+}$ phosphor prepared by spray method was found to be higher than those phosphor made by solid state reaction and the commercial $(Y,Gd)BO_3:Eu$ product.

• Applied Chemistry for Engineering
• /
• v.31 no.1
• /
• pp.19-24
• /
• 2020

In this study, the O/W emulsions prepared from coconut oil and the non-ionic mixed surfactant as Tween-Span system were evaluated and optimized in order to upgrade the stability of manufactured emulsions. For the optimization, a central composite design model-response surface methodology, so called as CCD-RSM was implemented. Quantitative factors were the hydrophile-lipophilie balance (HLB), amount of non-ionic mixed surfactant and emulsification speed while experimental results included the mean droplet size (MDS), emulsion stability index (ESI), and thermal instability index (TII). Optimized values of the HLB, amount of non-ionic mixed surfactant and emulsification speed obtained from CCD-RSM were 9.1, 8.7 wt.%, and 6,200.8 rpm, respectively. Expected experimental results for MDS, ESI, and TII under the optimized experimental condition were 151.0 nm, 99.86, and 3.17%, respectively. The average error from actual experiments which established for validation of the conclusions was lower than 3.5%. Therefore, a highly favorable level could be obtained when the optimized CCD-RSM was applied to manufacturing the O/W emulsion in this study.

• Applied Chemistry for Engineering
• /
• v.31 no.5
• /
• pp.532-538
• /
• 2020

In this study, emulsification process were conducted to manufacture the natural sunscreen from raw materials such as shea butter, olive emulsifier wax, and green tea extract. The emulsification was optimized by using the central composite design model-response surface methodology (CCD-RSM) where the response values were established as the mean droplet size (MDS) and emulsion stability index (ESI) after 7 days in addition to UV absorbance at 300nm. The amount of emulsifier and additives and emulsification time were established as operating variables and the optimal conditions of sunscreen emulsification were accepted as 3.70, 2.47 wt.%, and 15.42 min, respectively according to the result of CCD-RSM. On the other hand, the response values were estimated as 1173.80 nm and 99.56% for MDS and ESI, respectively, after 7 days, in addition to UV absorbance at 300 nm (2.47). The average error from actual experiments was a low level as about 3.0 ± 1.5%, which is mainly due to the fact that the optimization using CCD-RSM applied in this study was in the relatively high significant level.