• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.12
• /
• pp.50-57
• /
• 2009

This paper proposes a VLSI architecture of CAVLC hardware decoder which is a tool eliminating statistical redundancy in H.264/AVC video compression. The previous CAVLC hardware decoder used four stages to decode five code symbols. The previous CAVLC hardware architectures decreased decoding performance because there was an unnecessary idle cycle in between state transitions. Likewise, the computation of valid bit length includes an unnecessary idle cycle. This paper proposes hardware architecture to eliminate the idle cycle efficiently. Two methods are applied to the architecture. One is a method which eliminates an unnecessary things of buffers storing decoded codes and then makes efficient pipeline architecture. The other one is a shifter control to simplify operations and controls in the process of calculating valid bit length. The experimental result shows that the proposed architecture needs only 89 cycle in average for one macroblock decoding. This architecture improves the performance by about 29% than previous designs. The synthesis result shows that the design achieves the maximum operating frequency at 140Mhz and the hardware cost is about 11.5K under a 0.18um CMOS process. Comparing with the previous design, it can achieve low-power operation because this design is implemented with high throughputs and low gate count.

• Explosives and Blasting
• /
• v.26 no.2
• /
• pp.64-76
• /
• 2008

Bulk Emulsion blasts using mechanized charging system, which is generally used in foreign countries, have recently introduced and gradually increased in Korea. The Bulk Emulsion are safe and able to increase the charging density for improvement of fragmentation and advancement especially in tunneling, and minimizing environmental problem. Because of less toxic gas generation, the explosives are called, namely ech-friendly products. There are two kinds of Bulk Emulsion; one is for open cut and the other is for tunneling. According to features of blast sites and its purpose, the compositions are different, but the principle is the same. In this study, trial blasts using Bulk Emulsion for tunneling had executed at 10 sites in Korea. The major result of the major job-sites is the following. First of all, compared with cartridge explosive, Bulk Emulsion was able to increase its charging density up to $35{\sim}60%$, to decrease the blast holes to approximately $10{\sim}30%$ down, and the advancement was improved up to $8{\sim}20%$ and also 30% up in its fragmentation. Toxic gas production after cartridge blasting showed 34.44ppm of its CO. Bulk Emulsion, however, showed 20.13ppm, which was 58.45% production of the cartridge explosive, and NOx was below 2ppm. The mechanized charging system of Bulk Emulsion should be applied to large sized tunnel blasting, long advanced tunnel which can secure the advancement of over $4{\sim}5m$, and the sites required finishing rapidly.

• Journal of the Korean Vacuum Society
• /
• v.19 no.1
• /
• pp.66-71
• /
• 2010

Spherical shape $Zn_2SiO_4:Mn$ phosphor particles with the mean particle size from submicron to micron sizes were prepared by ultrasonic spray pyrolysis method. A droplet separator was introduced to control the size distribution of the phosphor particles with spherical shape. The $Zn_2SiO_4:Mn$ phosphor particles with 2 mol% doping concentration of manganese have decay time and have photoluminescence intensities comparable with those of the latest commercial product prepared by the solid state reaction method. The size of the phosphor particles was decreased from 1 to 0.2 micrometers as the inorganic salt solution concentration was changed from 0 to 5 M. The phosphor particles prepared from the solutions above 0.5 M have photoluminescence intensities comparable with that of the latest commercial product.

• Polymer(Korea)
• /
• v.26 no.2
• /
• pp.260-269
• /
• 2002

The fire resistance of particulate polypropylene composite systems were investigated by using various reinforced particles such as zeolite, talc, $CaCO_3$ particles. In this study, The effect of particle size on the thermal properties of composite and the effect of reinforced particles on the fire resistance were studied. The inorganic reinforced particles used in this study were recycled zeolite(average particle diameter=85.34 $mu extrm{m}$), $CaCO_3$ (33.93 $mu extrm{m}$), and talc (18.51 $mu extrm{m}$). The fire resistance of composite systems was thoroughly examined by measuring limited oxygen index (LOI, ASTM D2863) and cone calorimetry (ASTM E1354, ISO 5660). Thermal stability of composite systems was thoroughly examined by measuring TGA. The flame retardants (DBDPO) and reinforced particles reduce the maximum heat release rate (M-HRR) in the order of Talc > $CaCO_3$ > recycled Zeolite. Comparing the cone calorimetry experimental results of the particle reinforced polymer composite system exhibited twice higher efficiency than DBDPO in polypropylene systems, and the LOI also showed similar trends to the cone calorimetry experiments. The optical and scanning electron microscopy techniques were used to investigate the composites ash layer and the core fracture surfaces in the burning process. The reinforcing inorganic particles seemed to accumulate at the surface of ash layer, and subsequently intercept the oxygen transport and heat transfer into the core area.

• Journal of KIISE:Computer Systems and Theory
• /
• v.35 no.7
• /
• pp.305-317
• /
• 2008

As a mobile computing environment is rapidly changing, increasing user demand for multimedia-over-wireless capabilities on embedded processors places constraints on performance, power, and sire. In this regard, this paper proposes color media instructions (CMI) for single instruction, multiple data (SIMD) parallel processors to meet the computational requirements and cost goals. While existing multimedia extensions store and process 48-bit pixels in a 32-bit register, CMI, which considers that color components are perceptually less significant, supports parallel operations on two-packed compressed 16-bit YCbCr (6 bit Y and 5 bits Cb, Cr) data in a 32-bit datapath processor. This provides greater concurrency and efficiency for YCbCr data processing. Moreover, the ability to reduce data format size reduces system cost. The reduction in data bandwidth also simplifies system design. Experimental results on a representative SIMD parallel processor architecture show that CMI achieves an average speedup of 6.3x over the baseline SIMD parallel processor performance. This is in contrast to MMX (a representative Intel's multimedia extensions), which achieves an average speedup of only 3.7x over the same baseline SIMD architecture. CMI also outperforms MMX in both area efficiency (a 52% increase versus a 13% increase) and energy efficiency (a 50% increase versus an 11% increase). CMI improves the performance and efficiency with a mere 3% increase in the system area and a 5% increase in the system power, while MMX requires a 14% increase in the system area and a 16% increase in the system power.

• Journal of the Korean Society of Radiology
• /
• v.14 no.4
• /
• pp.439-445
• /
• 2020

The purpose of this study was to investigate the feasibility of stent placement and the evaluation of tissue hyperplasia caused by bare metallic stent placement in a mouse colon model. In a pilot study, C57BL/6 mouse were used to verify diameter of colon. Mean diameter size was 4.05 mm. Twenty C57BL/6 mice were divided into two groups to assess differing stent diameters (Group A, 5 mm diameter; Group B. Group B, 4 mm diameter). Follow-up, 1-week fluoroscopic imaging, 4-week endoscopic imaging were obtained. Mice were sacrificed 4-week after stent placement. Microscopic findings were evaluated. Stent placement was technically successful except one mouse in Group A. Data from the mouse was omitted. During follow-up, five mice in Group A died within 7 days after stent placement, and one stent in Group B was migrated into the rectum. The incidence of stent-related complication was 60% and 10% between group A and Group B, respectively. Gross and Endoscopic findings showed tissue hyperplasia through the mesh, and all the stents had become incorporated into the wall of the colon. Microscopic findings were no statistically significant difference. colonic stent placement was technically feasible, and stent-induced tissue hyperplasia was evident in a mouse model. With stent large size, there was the highest incidence of colon perforation.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.12
• /
• pp.1765-1777
• /
• 2002

본 연구에서는 현재 국내의 서울시내에 거주하는 모터사이클을 타는 만20세 이상의 남성을 대상으로 모터사이클복에 대한 착용실태와 불만사항들을 조사하고 이를 연령별, 모터사이클 유형별로 비교 분석하여 착용감 및 안전성이 향상된 모터사이클복 개발을 위한 기초자료를 제시 하고자 하였다. 설문조사는 2002년 1월~3월까지 3개월간 총 400부를 배부한 후 회수하고, 이 중 262부를 분석자료로 사용하여 빈도 및 백분율, 평균 등의 기술 통계치를 얻어 전반적인 착용현황을 알아보고, 교차분석을 실시한 후 X$^2$-검증을 실시하여 연령별, 모터사이클 유형별, 운행경력 별로 통계적인 차이를 비교 분석하였다. 1. 모터사이클복의 착용실태 및 불만사항 전반에 관한 조사결과, 조사대상자는 20대~40대의 운행경력은 5년 이상인 전문 라이더들이 많았으며 모터사이클의 배기량은 400cc이상이 가장 높게 나타났고, 모터사이클 유형은 로드 바이크가 가장 높게 나타났고, 이용목적은 레져.취미용, 선호하는 모터사이클복 아이템별 소재는 원피스와 슬랙스의 경우에는 피혁소재가 쟈켓의 경우에는 텍스타일 소재가 높게 나타났다. 아이템별 소유는 쟈켓과 투피스가 높게 나타났고, 보호구가 필요하다고 생각되는 신체부위는 상의에서는 가슴과 팔꿈치, 하의에서는 무릎으로 나타났으며, 무릎보호대의 소유도가 가장 높게 나타났다. 모터사이클복 주된 착용목적은 '부상방지', 모터사이클복을 착용하지 않는 이유는 '움직이기가 불편해서' '가격이 비싸서' '여름철에 더워서'가 각각 높게 나타났다. 모터사이클복에 대한 불만족도에서 동작적합성과 사이즈에 대한 불만도가 높게 나타났고, 모터사이클복소재 및 내부 장착 보호장구의 경량화가 요구되었으며, 모터사이클 쟈켓의 치수부적합부위는 소매길이가 가장높게 나타났다. 2. 전체 응답자의 연령을 20대, 30대, 40대 이상으로 나누어 연령별 차이를 비교한 결과 각각의 문항에 대해서 모두 연령대별로 유의차가 인정되었다. 3. 모터사이클복 아이템별 선호소재 문항에서 원피스와 쟈켓에서 모터사이클 기종별 유의차가 나타났는데, 비즈니스 기종에 서는 텍스타일 소재를, 아메리칸크루져 기종에서는 피혁소재를 선호하였다. 로드바이크와 오프로드 기종에서는 원피스는 피혁소재를 선호하였고, 쟈켓은 텍스타일 소재를 선호하는 것으로 나타났다.

• Membrane Journal
• /
• v.22 no.5
• /
• pp.332-341
• /
• 2012

We studied the effects of induction of natural convection instability flow (NCIF) according to the gravitational orientation (inclined angle) of the membrane cell on the reduction of membrane fouling in the constant-flow ultrafiltration (UF) of colloidal silica solutions. Five colloidal silica solutions with different silica size (average size = 7, 12, 22, 50 nm and 78 nm) were used as UF test solutions. The silica particles in colloidal solutions form cakes on the membrane surface thereby causing severe membrane fouling. The constant-flow UF performance according to the gravitational orientation of the membrane cell (from $0^{\circ}$ to $180^{\circ}$ inclined angle), was examined in an unstirred dead-end cell. We evaluate the effects of NCIF on the suppression of fouling formation by measuring the variation of transmembrane pressure (TMP) and the increase of critical flux by using the flux-stepping method. In the constant-flow dead-end UF for the smaller size (7, 12 nm and 22 nm) silica colloidal solutions, changing the gravitational orientation (inclined angle) of the membrane cell above the $30^{\circ}$ angle induces NCIF in the membrane module. This induced NCIF enhances back transport of the deposited silica solutes away from the membrane surface, therefore gives for the reduction of TMP. But in the constant-flow UF for the more larger size (50 nm and 78 nm) silica colloidal solutions, NCIF effects are not appearing. The critical flux is increased as increasing the module angle and decreasing the silica size. Those results show that the intesity of NCIF occurrence in membrane module is more higher as increasing the module angle and decreasing the silica size.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.8
• /
• pp.85-94
• /
• 2012

Evaluation of the smear effect caused by mandrel penetration into soft ground for a vertical drain installation is very important to predict the consolidation time of soft ground improvement. 30 kinds of laboratory model tests considering in situ conditions were conducted to investigate the formation of a smear zone and the decrease of coefficient of permeability in the disturbed zone. Three types(C(clay):M(silt)=1:1, 0.5:0.5, and 0:1) of reconstituted samples were used for 3 dimensional smear zone test. An experimental study was performed focusing on length of mandrel penetration, mandrel shape and size, earth pressure, and ground condition(unit weight and grain size distributions). Laboratory test results show that the length of mandrel penetration is the most critical factor for the formation of smear zone. As a result, the ratio between diameter of the smear zone($d_s$) and that of mandrel($d_m$) at field using long mandrel becomes larger than conventional $d_s/d_m$. The ratio between $d_s$ and $d_m$ ranges from 1.89 and 2.48 with the sample at C:M=1:0. It was also found that the $d_s/d_m$ value with the round shape of the mandrel is smaller than that of diamond one. The value of $d_s/d_m$ decreased with larger mandrel size, lower unit weight, and higher earth pressure. However, higher silt content led to increase of $d_s/d_m$. The ratio between coefficient of horizontal permeability in the smear zone($k_{hs}$) and that of undisturbed zone($k_{ho}$) ranged from 0.70 to 0.85. The test results imply that factors and values affecting $k_{hs}/k_{ho}$ show similar tendency with $d_s/d_m$.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.4
• /
• pp.325-332
• /
• 2010

This study was conducted with the experiment of solubilisation of excess sludge by microbubble ozone process. To improve ozone contact efficiency, microbubble ozones which its diameter were the avearge 30 ${\mu}m$, microbubble size less than 40 ${\mu}m$ occupied about over 90% of all. In treating sludge using microbubble ozones, in case microbubble ozones are injected at microbubble ozone dosage of 0.34 g $O_3/g$ SS or less regardless of sludge concentration, microbubble ozone consumption rate was found to be 100% with no emission of waste ozones. In treating sludges by each concentration, in case the initial SS concentration of sludge is set to 6,447 mg/L, 5,557 mg/L, 3,180 mg/L, 1,092 mg/L and 515 mg/L, the amount of removed SS tended to increase with increase in initial SS concentration for the same microbubble ozone dosage, and treatment of sludge with high initial SS concentration was effective in raising the oxidation efficiency of microbubble ozones. On the other hand, as a result of reviewing acid, alkali and microbubble ozone treatment as composite treatment of sludge, use of acid treatment for the pre-treatment of microbubble ozone was more effective than alkali treatment, and in case of treatment at microbubble ozone dosage 0.05g $O_3/g$ SS with the concentration of sulfuric acid infused in the sludge, the amount of removed SS, 153.9 g, was 1.9 times more than 81.2 g the amount of single treatment of microbubble ozone.