• Proceedings of the Korean Fiber Society Conference
• /
• 2003.10b
• /
• pp.245-246
• /
• 2003

최근 정보통신 산업의 급속한 성장으로 평판 표시소자의 개발에 많은 관심이 모아지고 있다. 특히 이 중에서 액정 표시소자(LCD)의 수요는 급증하고 있으며 그에 관련된 부품 및 소재의 중요성 또한 강조되고 있다. LCD 부품 및 소재에서 가장 중요한 역할을 하는 편광필름은 일반적으로 PVA (polyvinyl alcohol) 또는 polyene 구조를 갖는 고분자 필름에 요오드를 염착시켜 사용되어 왔다. 본 연구에서는 PVA Film에 저온 플라즈마 처리를 함으로서 편광도와 투과도에 어떠한 영향을 미치는지에 대해 알아보고자 한다. (중략)

• Polymer(Korea)
• /
• v.24 no.5
• /
• pp.713-720
• /
• 2000

A polymer/iodine complex film was prepared using syndiotactic poly(vinyl alcohol) (s-PVA) with number-average degree of polymerization of 900 and syndiotactic diad content of 63.1%. In comparison with atactic-PVA/iodine films, degree of polarization of the s-PVA/iodine film was improved up to over 99% although a lower transmittance was obtained. By soaking in iodine/potassium iodide aqueous solution of a lower iodine concentration and subsequent drawing by 4 times, s-PVA/iodine film of a higher transmittance and degree of polarization was produced. The degree of iodine desorption of the s-PVA/iodine film in water were very low. The crystallinity and the d-spacing and crystal size of (100) plane increased at the early stage of soaking time, however, remained constant or decreased slightly with increasing soaking time. In consequence, s-PVA/iodine complex formation took place mainly inside crystal region at the initial stage of soaking time, whereas it occurred outside crystal region or physical adsorption of iodine dominated after sufficient soaking.

• Korean Journal of Optics and Photonics
• /
• v.29 no.6
• /
• pp.262-267
• /
• 2018

In this paper, we designed a new antireflective film to improve the optical efficiency of organic light-emitting diode displays (OLEDs). The reflection characteristics in the normal and side viewing directions of OLEDs with the antireflective film were calculated, depending on the degree of polarization and transmittance of the currently used polarizer when used in the antireflective film of an OLED. The results showed that when the polarization degree of the commercial polarizer (99.990~99.995%) is lowered to 99.900%, the average reflectance of the antireflective film is increased by about 0.1% (2.5% in terms of rate of increase) which is difficult to notice with the human eye, while the transmittance is increased by 1.63~3.34% (4.2~8.2% in terms of rate of increase). This study provides an optimal design for high-light-efficiency OLEDs with good antireflection properties.

• Applied Chemistry for Engineering
• /
• v.19 no.6
• /
• pp.661-667
• /
• 2008

In this study, cholesteric liquid crystal (CLC) was synthesized and applied as a polarizing component on the optical film of back light units (BLU) for LCDs. After mixing CLC with nematic liquid crystal, this mixture was fulfilled in the module consisting of two films and then its amplifying efficiency and polarizing ability for a planarly emitted light were examined to apply as a BLU polarizer film for increasing the brightness of light. The properties of CLC compound were tested by UV/Visible spectroscopy and polarizing optical microscopy (POM). Flexible spacer was made by linear carboxylic acid group of cholesteric derivatives between cholesterol mesogen units for one-axis orientation in each layer. The CLC containing film could be used as a module to increase the ability of polarization and to enhance brightness of BLU and to widen wavelength range by stacking the films.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2006.11a
• /
• pp.67-69
• /
• 2006

• Polymer(Korea)
• /
• v.36 no.3
• /
• pp.344-350
• /
• 2012

New pressure sensitive adhesives (PSAs) for polarizer film were prepared by electron beam (e-beam) radiation to acrylic copolymers, and their adhesive properties were investigated. The acrylic copolymers were synthesized by free radical polymerization of $n$-butylacrylate (BA), 2-hydroxyethyl methacrylate (HEMA), and acrylic acid (AA). The acrylic copolymers were coated on PET release films to a thickness of 25 ${\mu}m$, laminated to polarizer films, and then radiated with e-beam at room temperature. Gel fractions of all the acrylic copolymers after e-beam radiation at 50 kGy were higher than 93%, and their crosslinking densities were increased with increasing the content of HEMA units. PSA prepared by e-beam radiation of acrylic copolymer synthesized with a feed ratio of BA/HEMA/AA = 89.5/10/0.5 (w/w/w) at a dose of 50 kGy exhibited the best adhesion performances in terms of peel strength, creep resistance, durability and reliability, and light leakage. It is expected that the preparation method of PSAs via e-beam irradiation will improve the producibility and workability of polarizer film for liquid crystal display.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.19 no.6
• /
• pp.743-748
• /
• 2009

In this paper, we propose an effective method to extract background components in automated vision inspection system for polarized film used in TFT LCD display panels. The test image signals are typically composed of three components such as ununiform background, random noises and target defect signals. It is important to analyze the background signal for accurate extraction of defect components. Two dimensional continuous wavelets with first derivative gaussian is used. This methods can be applied for reliable extraction of defect signal by elimination of the background signal from the original image. The proposed method outperforms over conventional FFT methods.

• Polymer(Korea)
• /
• v.34 no.6
• /
• pp.560-564
• /
• 2010

Dimensional stability of LCD polarization film consisted of triacetyl cellulose (TAC) and poly(vinyl alcohol) (PVA) film has been studied and especially, the effect of PVA adhesive on the dimensional stability has been considered as function of deacetylation and molecular weight of PVA adhesive. The maximum adhesion strength between TAC and PVA film was obtained in the laminate using PVA adhesive with 70% of OH content and the effect of molecular weight on the adhesion strength was only pronounced in the laminate using PVA adhesive with OH content above 70%. It was found that the optimum dimensional stability of TAC/PVA/TAC laminate (polarizing film) was obtained when applied PVA adhesive has low molecular weight and it was more dependent upon the OH content than the adhesion strength between TAC and PVA films.

• Polymer(Korea)
• /
• v.35 no.5
• /
• pp.458-466
• /
• 2011

In the mixed system of supercritical carbon dioxide/organic solvents, poly(vinyl alcohol)(PVA) film of high degree of hydrolysis could be dyed with a dichroic dye of C. I. direct black 22(DB22) and as a result, high durability was obtained. Especially, as a dye dispersant in a supercritical fluid phase, a mixed solvent system of ethylene glycol: dimethyl sulfoxide=4 : 6 weight ratio was investigated. Then the optimum pressure for dyeing could be reduced down to 200 bar. Using this supercritical fluid system, the maximum dyeing appeared as the transmittance of less than 1% and the waste amount was reduced to the level of 1/10. After 500% drawing of this PVA film, both the polarizing efficiency of 94% and the single piece transmittance of 30% were obtained. The limitation of DB22 and further improvements were also discussed.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.3
• /
• pp.78-82
• /
• 2023

A fabrication of smart windows with controllable visible light transmittance in three steps by using λ/2 retardation films based on a reactive mesogen (RM) material and polarizing films is demonstrated. The phase retardation films with a Δn·d value of λ/2 (λ: wavelength) convert the direction of a traveling light to the optical axis of the film symmetrically. In this work, the retardation characteristics according to the RM thickness were evaluated and henceλ/2 phase retardation film can be fabricated. The phase retardation film with Δn·d of 276.1 nm, which is close to λ/2 (=275 nm @550 nm), was fabricated. The light transmittance of a smart window with the structure of (polarizing film)/(glass)/(alignment layer)/(λ/2 retardation film) was measured in the transmission mode, half mode and blocking mode. The evaluation results show that the transmittance of the smart window can be controlled in three steps with 35.8%, 27.8%, and 18.2% at each mode, respectively. In addition, by fabricating a smart window with a size of 15×200 mm², the feasibility of use in various fields such as buildings and automobiles was verified.