• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.171.1-171.1
• /
• 2005

• Proceedings of the Korean Fiber Society Conference
• /
• 2002.04a
• /
• pp.337-340
• /
• 2002

부직포의 제조공정은 기본적으로 웹성형공정과 웹결합공정으로 구성되어 있다. 웹성형공정에는 단섬유를 중심으로 건식법과 습식법 및 장섬유를 중심으로 스펀본드법[1]이 있다. 웹결합공정에는 니들펀칭과 접착제, 열응착, 스펀레이스 및 스티치공정 등 여러공정법이 응용되고 있다. 이러한 공정의 선택은 개발목표로 하는 최종제품의 특성과 용도에 의해 결정된다. 일반적으로 동일중량을 기준에서 볼 때, 고강도 고강제조공정상 경량제품에는 주로 열융착방법을 선택하며 중량제품에는 니들펀칭공정을 사용하고 있으며 그 한계는 웹결합공정 특성상 약 150g/$m^2$ 내외이다. (중략)

• Proceedings of the Korean Fiber Society Conference
• /
• 1997.10a
• /
• pp.234-237
• /
• 1997

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.287-290
• /
• 2005

The shearing and punching processes are analyzed with the finite element method using an isotropic material model. The experimental result in the punching process shows that final radiuses of sheet metal according to the rolling direction and transverse direction are different because of the material anisotropy. The material anisotropy is induced by complicated large deformation in the polycrystalline aggregate. The contact region between the punch and sheet metal experiences severe deformation such as shear, compression and tension in the punching process. In this paper, the analysis of punching process for Al 1100 is performed with the ABAQUS Standard. The analysis of texture development and evolution is carried out based on the deformation history in the punching process. The deformation histories are extracted by UMAT in the ABAQUS Standard. The torture development is investigated with the pole figure and yield surface during the punching process.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.159-162
• /
• 2005

The milli-components for electronic and medical device etc. have been manufactured by conventional process. Forming and machining process for those milli-components need tremendous cost and time because products require higher dimensional accuracy than the conventional ones. For instance, conventional mechanical punching process has many drawbacks for applying to high accuracy products. The final radius of hole can be varied and burr which interrupting another procedure is generated. Hydro-mechanical punching process makes possible to reduce amount of burr and obtain the fine shearing surface using the operating fluid. Hydrostatic pressure retards occurrence of initial crack and induces to locate the fracture surface in the middle of sheet to thickness direction. In this paper, Hydro-mechanical punching process is analyzed using finite element method and the effect of hydrostatic pressure is evaluated during punching process. The prediction of fracture is performed adopting the various ductile fracture criteria such as Cockcroft, Brozzo and Oyane's criterion using a user subroutine in ABAQUS explicit.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.05a
• /
• pp.184-187
• /
• 2002

Compression molding was specifically developed for replacement of metal components with composites. As the mechanical properties of the products are dependent on the separation and orientation, it is important to research the fiber mat structure and molding conditions. In this study, the effects of the fiber mat structure(NP: 5, 10, 25punches/$\textrm{cm}^2$) and the mold closure speed($\dot{\textrm{h}}$=0.1, 1, 10mm/min) on the viscosity of composites were discussed. The composites is treated as a Non-Newtonian power-law fluid. The parallel-plate plastometer is used and the viscosity is obtained from the relationship between the compression load and the thickness of the specimen.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.5 no.3
• /
• pp.51-57
• /
• 2006

Hydro-mechanical punching was developed for preventing burr formation. Circular hole punching and Finite element method(FEM) analysis were conducted to investigate shearing characteristics of this process in comparison with conventional and mechanical counter punching. In this process hydrostatic pressing with appropriate medium was utilized instead of counter punch, which resulted in the delay of the point that the fracture is initiated and clean shearing surface was obtained. FEM analysis was utilized to find out optimum processing parameters and shearing mechanism for burr-free hole punching.

• Applied Chemistry for Engineering
• /
• v.20 no.5
• /
• pp.561-564
• /
• 2009

Filter media finely interspersed with activated carbons were prepared by a needle punching process without using chemical binders. Their characteristics were investigated efficiently to abate environmentally harmful gas such as acetaldehyde, and were compared with those of cabin air filter coated with activated carbons by using chemical binders. These combination filters were installed on a vehicle fan placed in a test chamber of capacity similar to the interior volume of a commercially available passenger car, and the efficiency of acetaldehyde abatement was measured as a function of time. The filter utilizing chemical binders showed somewhat better performance for the elimination of acetaldehyde despite the adverse effect of the chemical binder that would clog the micropores of the activated carbons. It turned out that the needle punching process had the activated carbons agglomerated due to hydrophobic interactions, resulting in a relatively larger void area than that of the filter utilizing chemical binders.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.63-66
• /
• 2003

The effect of punching density and material composition on the tensile properties and optimum condition of manufacturing of carbon needle punched perform was studies. The interlaminar tensile strength were increased but the intralaminar tensile strength were decreased with increasing punching density. In the case of the performs composed of continuous oxi-PAN fabrics, there was a considerable improvement of the interlaminar and intralaminar tensile strength.

• Transactions of Materials Processing
• /
• v.15 no.3 s.84
• /
• pp.220-225
• /
• 2006

This paper investigates the characteristics of a hydro-mechanical punching process. The hydro-mechanical punching process is divided into two stages: the first stage is the mechanical half piercing in which an upper punch goes down before the initial crack is occurred; the second stage is the hydro punching in which a lower punch goes up until the final fracture is occurred. Ductile fracture criteria such as the Cockcroft, Brozzo and Oyane are adopted to predict the fracture of sheet material. The index values of ductile fracture criteria are calculated with a user material subroutine, VUMAT in the ABAQUS Explicit. The hydrostatic pressure retards the initiation of a crack in the upper region of the blank and induces another crack in the lower region of the blank during the punching process. The final fracture zone is placed at the middle surface of the blank to the thickness direction. The result demonstrates that the hydro-mechanical punching process makes a finer shearing surface than the conventional one as hydrostatic pressure increases.