• Computational Structural Engineering
• /
• 제10권3호
• /
• pp.39-45
• /
• 1997

최근 우리 주변에는 기계, 구조물의 고속화 및 대형화에 따른 충격하중의 발생빈도가 급격하게 증가하고 있다. 따라서 이와 같은 충격하중을 받는 기계 및 구조물의 안전성 및 신뢰성 확보를 위하여는 먼저 충격하중 특성을 고려한 내충격 설계기법의 확립이 필요하다. 특히 충격하중의 경우 종래의 파괴역학적 관점에서 주로 다루어 왔던 정적하중 및 피로하중 하에서의 재료거동 특성과 달리 응력파의 전파특성이 재료의 충격강도 및 균열발생, 전파특성에 큰 영향을 미치기 때문에 이를 고려한 역학적 검토가 필요하다. 한편 이와 같은 충격하중이 반복적으로 작용하는 충격피로의 경우 지금까지 많은 연구로 내피로 설계기법이 확립된 일반 피로 특성과 달리 아직 그 주요 메카니즘이 규명되지 않은 부분이 많아 이 부분에 대한 체계적인 연구가 국내에서도 요구된다.

• The Journal of Engineering Geology
• /
• 제27권1호
• /
• pp.51-58
• /
• 2017

The purpose of this study was to quantitatively evaluate the state of rocks in load steps by using the low-frequency ultrasonic flaw detection method. The initial Vp-velocities measured with a CND tester were in the order of Z-axis < X-axis < Y-axis, with 1687.5 m/s along the X-axis, 1690.7 m/s along the Y-axis, 1548.3 m/s along the Z-axis, and an average of 1642.2 m/s. The overall average of the Q vlaues, measured with a Silver Schmidt hammer, was 62.6, which corresponds to a uniaxial compressive strength of ~105 MPa. The Vp-velocity, measured with a low-frequency ultrasonic flaw detector at load steps of 50%, 60%, 70%, and 80%, typically decreases in the order of X-axis < Y-axis < Z-axis with increasing load steps. This oder contrasts with that of the initial Vp-velocities. As the load step increases the factors that reduce the Vp-velocity in the X-axis direction are more influential than those in the Y-axis or Z-axis directions. This indicates that the initial state of rocks can vary and is dependent on the stress state.

• Computational Structural Engineering
• /
• 제10권4호
• /
• pp.195-203
• /
• 1997

The interaction between cracks and stress wave due to impact and explosive loads is numerically calculated in the study. The interaction and the effects of stress wave are numerically examined with the application of Bicharacteristic Method. This method has been used with confidence for its reliability in reproducing the realistic and physical wave pattern in the complete solution domain. The dynamic stress intensity factor, K/sub I/(t) for cracks under impact loads are numerically simulated and its results are compared favorably with Kalthoff's experimental output. Also the influence of stress wave to the dynamic stress intensity factor for the case of two symmetric holes around cracks are investigated. The results of study are also compared favorably with the experiment and proven to be applied to the structures exposed to impact and explosive loads.

• Proceedings of the Korea Concrete Institute Conference
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.1033-1036
• /
• 2008

In this paper, the analysis of impact damage behavior of a reinforced concrete structure that undergoes both a shock impulsive loading and an impact loading due to the air blast induced from an explosion is performed. Firstly, a pair of multiple loadings are selected from the scenario that an imaginary explosion accident is assumed. The RC structures strengthened with glass fiber reinforced polymer (GFRP) composites are considered as a scheme for retrofitting RC wall structures subjected to multiple explosive loadings and then the evaluation of the resistant performance against them is presented in comparison with the result of the evaluation of a RC structure without a retrofit. Also, in order to derive the result of the analysis similar to that of real explosion experiments, which require the vast investment and expense for facilities, the constitutive equation and the equation of state (EOS) which can describe the real impact and shock phenomena accurately are included with them. In addition, the numerical simulations of two concrete structures are achieved using AUTODYN-3D, an explicit analysis program, in order to prove the retrofit performance of a GFRP-strengthened RC wall structure.

• Journal of the Korean Society of Marine Environment & Safety
• /
• 제19권2호
• /
• pp.200-206
• /
• 2013

The paper was investigated on the mooring forces(or tension) and motion response characteristics for a 8-point mooring floating dock in regular waves using a commercial code(AQWA). To achieve the aim of the research, a numerical simulation was adapted on an inner port environment condition, which the water depth is 10 meters, significant wave amplitude(1.05 m). wave period(3.85 sec), wind speed(20.21 m/s), wind and current direction ($90^{\circ}$), incident waves(${\chi}=180^{\circ}$, $135^{\circ}$ and $90^{\circ}$). The dimension of the numerical model is length(140 m), breadth(32 m), depth(14.6 m). The maximum length of a mooring line is 120m. We can expected that roll and pitch motions appeared in beam seas better than head sea. the mooring forces also indicated higher in bean seas than in head seas including wind forces.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 한국음향학회 1998년도 학술발표대회 논문집 제5권
• /
• pp.9-12
• /
• 1998

공기경계층을 갖는 유리평판에서 힘의 크기가 10N이고 상승시간이 약 280ns 인 경사 점하중이 인가된 경우에 대하여 진앙점에서 입자 변위와 입자 속도를 계산하였다. 이론적으로 계산된 수직성분이 입자속도가 PZT변환자에 입사한다고 가정하여 PZT 변환자의 과도 응답특성을 Mason 등가회로와 격자점을 이용하여 계산하였다. 유리모세관의 파과시에 방출괴는 과도탄성파를 이용하여 유리평판의 진앙점에서 PZT 변환기의 응답을 조사하였고, 이론과 비교한 결과 상당히 일치하였다. 이를 이용하여 음향방출 시스템인 발생원, 전파매질, 변환자 및 신호분석시스템을 수학적으로 모형화할 수 있는 기초를 마련하였다.

• Geophysics and Geophysical Exploration
• /
• 제14권4호
• /
• pp.324-334
• /
• 2011

Seismic wave velocity change has been monitored due to the accumulation of micro-cracks by uniaxial loads on the rock samples from Seokmo Island with stepwise increase in 5 stages. After the load was applied up to 95% of UCS, P- and S-wave velocities varied in ranges of 0.9 ~ 18.3% and 2.8 ~ 14.8% of fresh rock sample velocities, respectively. Unlike seismic velocity of the dry rock samples that showed overall decreases after the loading, velocity changes of saturated rock samples were much more complicated. These seemed to be due to the mixture of two contradictory mechanisms; i.e. accumulation of micro-crack causes an increase in porosity and a decrease in wave velocity, while saturation causes an increase in wave velocity. Most of tested rocks showed a trend of velocity increase with low axial load and then velocity decrease at later stages. Starting stage of velocity decrease differs from samples to samples. After the failure of rock occurred, noticeable increases of porosity and decreases of wave velocity have been observed. It showed overall trend that the more the quartz contents and the lower the silicate, the higher the Young's modulus.

• The Journal of Engineering Geology
• /
• 제16권3호
• /
• pp.235-244
• /
• 2006

Granite cores were sampled within Korea Atomic Energy Research Institute and cyclic loadings up to 1550 cycles were applied. Microcrack development in samples due to cyclic loading was estimated using Acoustic Emission(AE) method. AE showed two different types depending on numbers of cycle. Type 1 appeared at low cycles and had low energy and diverse frequencies, while type 2 appeared at high cycles and had high energy and uniform frequency. AE property of type 1 indicates voids and pre-existing microcracks in samples may close or propagate up to certain length. Microcracks may be sheared or closed during loading and are recovered from shear or opened during unloading when AE of type 2 were measured. P wave velocities and Felicity ratios were measured at 50, 150, 350, 750, 1550 cycles. P wave velocities were almost the same regardless of number of cycles applied. However, Felicity ratios were much lower than 0.9, indicating that microcracks were developed within samples. This result indicates that Felicity ratio is a better tool than P wave velocity to estimate the damage of rock.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• 제22권1호
• /
• pp.45-52
• /
• 2009

In this paper, a guideline for designing breakwater in wave loads and in seismic loads is proposed. A simple model structure in breaking wave zone is examined using Morison equation in consideration with the effect of an impact load, for evaluation of the wave loads. As the impact load effect is not significant, pressure distributions according to Goda are applied for evaluation of wave loads on breakwater. Structural behavior of breakwater in wave loads can be obtained using the Goda method, as well. For seismic analysis, Ofunato and Hachinohe models, as well as an artificial seismic acceleration loads model, are adopted. Soil-structure interaction analysis is carried out to find the seismic load effect. It is found that, in certain cases, structural deformation in wave loads is in the same level as deformation that in seismic loads. Thus, it is our recommendation that these two loads are considered at the same level in breakwater design.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제21권4호
• /
• pp.673-678
• /
• 1997

Stress wave propagations in an elastic half space to a normal point force of ramp type in time are analyzed. The governing equations are transformed by applying the Laplace and Hankel transforms with respect to time and radial distance. The inversion of Laplace transforms are performed by employing the Cagniard-de Hoop method, where the Rayleigh waves at surface are obtained by including the residue terms. The stress waves computed at the location very cose to the surface are shown to be almost identical to the surface waves obtained by the residue method except the Rayleigh wavefront. It is found that at the surface, the stresses are dominated by the Rayleigh waves, whose amplitudes increase linearly with time when time is very large. It is also found that in the interior part, the radial stress has a logarithmic singularity at the shear wavefront, while tangential stress shows no singularity.