• 대한기계학회논문집A
• /
• 제33권7호
• /
• pp.681-686
• /
• 2009

Direct laser metal forming technology was applied to restore the damaged mold surface. In order to estimate melting characteristics of the $20{\mu}m$ Fe-Cr-Ni powder, single layer experiments were performed at various levels of heat input. The process window of the $20{\mu}m$ Fe-Cr-Ni powder provided feasible process parameters for the smooth regular surface. The cross hatching scanning strategy on the multiple layer experiment was performed to reduce the thickness non-uniformity of edge portions compared with the one direction scanning. To estimate the coherence between the melted powder and the basematal, the tendency of hardness distribution has been observed. The hardness of the melted and the remelted zone was distributed from 400HV to 600HV. It is over 2 times compared of the hardness of the basemetal. Experimental results show that the mold restoring process using direct laser metal forming can be successfully applied in the mold repair industry.

• 새물리
• /
• 제69권10호
• /
• pp.1107-1114
• /
• 2019

다양한 기능의 새로운 물질을 합성하고 정적 및 동적 특성을 조사하기 위해서는 매우 안정된 고온 및 고압 조건을 만드는 것이 중요하다. 새로운 물질을 제조하는 데 필요한 다이아몬드 엔빌 셀 (DAC)을 사용하여 Mbar 범위의 고압 조건은 이미 확보되었다. 이 연구에서는 DAC와 결합된 레이저 가열 시스템을 설계하였으며, DAC의 양쪽 방향에서 시료를 가열하기 위해 2 대의 1064 nm, 100 W 파이버 레이저를 사용했을 뿐만 아니라 3 대의 분광기를 사용하여 온도, 압력 및 라만 스펙트럼을 측정하였다. 고압 실험에서 시료를 가두는 구멍으로 일반적으로 사용되는 스테인리스 강 개스킷을 가열하여 열 방사선원을 만들고, 이 방사선원으로부터 방출되는 복사 스펙트럼을 획득하여 가열된 개스킷의 온도를 측정하였다. 이 기술을 적용하여 다양한 물질들을 만들고 극한 조건에서 물리적 특성을 조사 할 수 있다.

• 한국정밀공학회지
• /
• 제30권9호
• /
• pp.931-942
• /
• 2013

In this study, we analyzed and compared the ultrasonic welding with the laser welding for the pure aluminium thin plates in a series of secondary lithium-ion batteries which are currently being produced by the ultrasonic welding; and performed the experiment for the purpose of the preceding study to replace the ultrasonic welding method with the laser welding method. As a result, the weld width of ultrasonic welding was 5mm, but that of laser welding was about 1~1.5 mm. As a result of tension test, the tensile strength was high when the pulse duration hour was short at the low peak power, while the high tensile strength was achieved when the pulse duration hour was long at the high peak power. The value of tensile strength was higher in the ultrasonic welding while the laser welding showed a maximum 45% better result as for the welding width.

• 한국정보통신학회논문지
• /
• 제6권7호
• /
• pp.1095-1099
• /
• 2002

본 논문은 1064 m의 Q-스위칭 Nd:YAG로 펌핑된 단일통과 라만레이저에서 nano-초의 스토크스 펄스발생에 관한 연구이며, 라만 매질로는 GeO2로 도핑된 grad index형 다중모드 파이버 220 m를 사용하였다. 실험 결과에서 펌핑 에너지의 변화에 따라 1.5∼2.7 nano 초의 펄스폭을 갖는 스토크스 펄스 트래인 싱분이 효율적으로 발생함을 알 수 있었다.

• Journal of Welding and Joining
• /
• 제34권5호
• /
• pp.6-12
• /
• 2016

This study was performed bead welding of pure titanium by using fiber laser. Since titanium is very sensitive to oxidation and nitriding during welding, it is important to compose the shielding equipment compared with different material. Thus side and coaxial shield nozzle, rail and chamber type shielding equipment are widely used to protect effectively the weld during welding. Experiments were performed by changing nozzle angle and distance using side and coaxial shield nozzle. The bead colors of gold, brown, blue, purple and yellowish white were obtained by changing variables of shield nozzle, and then its weldability was investigated. As experiment result, sound and not brominated beads were formed when side nozzle angle and distance were respectively $45^{\circ}$ and 10 mm.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2207-2208
• /
• 1999

In this paper, we would like to study the oscillation characteristics of single mode fiber laser which is composed of a Fabry-Perot resonator, a pump source of 808nm Laser Diode, a $Er^{3+}$ doped single mode fiber with 0.5um diameter.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2002년도 춘계종합학술대회
• /
• pp.271-274
• /
• 2002

본 논문에서는 광센서용 광원에 적합한 1.55$\mu\textrm{m}$ 파장대의 InGaAsP/InP 반도체레이저를 제작하였다. 레이징을 억제시켜주기 위해서 bending type의 소자를 설계 및 제작하였으며, 제작된 소자의 출력은 펄스 구동전류 100㎃에서 1.6㎽이고, 스펙트럼 폭은 40nm의 값을 가졌다. 그리고, 제작된 광원을 적용하였을 때 광섬유 자이로스코프에 파이버 종단에서의 출력은 $25^{\circ}C$, 직류 100㎃에서 540㎻였고, 스펙트럼 폭은 53nm였다. 그리고, 불규칙잡음 계수는 2.5$\times$10­$^3$deg/√hr였고, 자이로 출력 drift도 잡음수준으로 조사되었다. 따라서, 본 연구에서 제작한 광원을 광섬유 자이로 스코프에 사용 가능함을 확인하였다.

• Journal of Welding and Joining
• /
• 제32권6호
• /
• pp.64-69
• /
• 2014

The applications by using fiber laser have increased recently. However, due to high beam quality of fiber laser, it is inappropriate to apply the existing laser welding monitoring technology to the fiber laser welding as it is. On this study, thus, we analyzed emission signal with RMS and FFT for the in-process monitoring during fiber laser welding. 12mm-thick 304L stainless steel sheet was used in fiber laser welding and the result showed as follows: The intensity changes in RMS did not clarify the distinction between full penetration and partial penetration. However, as welding speed increases, specific frequency also increases in regards of frequency analysis by using FFT.

• Journal of Welding and Joining
• /
• 제32권6호
• /
• pp.56-63
• /
• 2014

To develop and understand dissimilar metals joining of Stainless steel and Copper, ultra-high speed laser lap welding was studied using single mode fiber laser in this study. SUS304 and Cu have large differences in materials properties, and Cu and Fe have no intermetallic compounds by typical binary phase of Cu and Fe system. In this study, ultra-high speed lap welds of SUS304 and Cu dissimilar metals using single-mode fiber laser was generated, and weldability of the weld fusion zone was evaluated using a tensile shear test. To understand the phenomenon of tensile shear load, weld fusion zone of interface weld area and fracture parts after tensile shear test were observed using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) analysis system. And it was confirmed that Cu was easily melting and penetrating in the grain boundaries of SUS304 because of low melting temperature. And high thermal conductivity of copper occurred dissipate heat energy rapidly. These properties cause the solidification cracking in weld zone.

• Journal of Welding and Joining
• /
• 제32권6호
• /
• pp.70-74
• /
• 2014

On this study, we researched the in-process monitoring during fiber laser welding as well as on the first paper. On the previous/formal study, we analyzed the change of emission signal on thin plate welding. On this study, however, we analyzed RMS and FFT with emission signals in laser welding on lap joint and butt joint of 8mm-thick 316L stainless steel. As the result, the movement of specific frequency peak was observed according to welding speed changes. Furthermore, frequency peak as a result of FFT on the thick plate welding are much clearer than on the thin plate welding. Therefore, it is expected that the welding parameter changes can be predicted in case of applying FFT to in-process monitoring.