• Title/Summary/Keyword: 파손기구

Search Result 42, Processing Time 0.021 seconds

Development of a Short-term Failure Assessment of High Density Polyethylene Pipe Welds - Application of the Limit Load Analysis - (고밀도 폴리에틸렌 융착부에 대한 단기간 파손 평가법 개발 - 한계하중 적용 -)

  • Ryu, Ho-Wan;Han, Jae-Jun;Kim, Yun-Jae;Kim, Jong-Sung;Kim, Jeong-Hyeon;Jang, Chang-Heui
    • Transactions of the Korean Society of Mechanical Engineers A
    • /
    • v.39 no.4
    • /
    • pp.405-413
    • /
    • 2015
  • In the US, the number of cases of subterranean water contamination from tritium leaking through a damaged buried nuclear power plant pipe continues to increase, and the degradation of the buried metal piping is emerging as a major issue. A pipe blocked from corrosion and/or degradation can lead to loss of cooling capacity in safety-related piping resulting in critical issues related to the safety and integrity of nuclear power plant operation. The ASME Boiler and Pressure Vessel Codes Committee (BPVC) has recently approved Code Case N-755 that describes the requirements for the use of polyethylene (PE) pipe for the construction of Section III, Division 1 Class 3 buried piping systems for service water applications in nuclear power plants. This paper contains tensile and slow crack growth (SCG) test results for high-density polyethylene (HDPE) pipe welds under the environmental conditions of a nuclear power plant. Based on these tests, the fracture surface of the PENT specimen was analyzed, and the fracture mechanisms of each fracture area were determined. Finally, by using 3D finite element analysis, limit loads of HDPE related to premature failure were verified.

An Analysis on Durability Improvement of Twist Run Exercise Equipment (트위스트 런 운동기구의 내구성 향상에 관한 해석)

  • Han, Moon Sik;Cho, Jae Ung
    • Journal of the Korean Society of Manufacturing Process Engineers
    • /
    • v.13 no.5
    • /
    • pp.116-122
    • /
    • 2014
  • In this study, 2 kinds of twist run models as exercise equipments are compared by durability analyses of fatigue and vibration. Maximum equivalent stresses are shown as 3.3 MPa and 16.6 MPa at the parts of stress concentrations at models 1 and 2. As the values becomes much lower than yield stress of this models, these models are shown to be safe designs. Model 1 becomes stronger than model 2 at natural frequency analysis. Fatigue lives become lowest at four axis parts and one axis part respectively in cases of models 1 and 2. Maximum damage probability at fatigue is shown to be 2.4% near the average stress of 0 in case of model 1 but this probability becomes 0.6 % in case of model 2. Model 1 has the maximum damage possibility 4 times more than model 2 at these states. As the result of this study is applied by the design of twist run, the prevention on fatigue damage and the durability are predicted.

A Study on the Micro-mechanical Characteristics of Titanium Metal Matrix Composites (티타늄 금속기 복합재료의 미시-기계적 특성에 관한 연구)

  • 하태준;김태원
    • Composites Research
    • /
    • v.17 no.1
    • /
    • pp.47-54
    • /
    • 2004
  • Vacuum hot pressing has been used for the development of titanium metal matrix composites using foil-fiber-foil technique. Subsequent micro-mechanical characteristics of the composites are then investigated by means of several experimental methods. The levels of consolidation, together with mechanism based failure processes of the materials have been analyzed by employing a thermo-acoustic emission technique. As shown by the results, fiber strength degradation occurs during the consolidation, and particularly residual stresses results from the thermal expansion mismatch between fiber and matrix materials during cooling process are incorporated in the changes of mechanical properties of the finished products. In industrial applications, both qualitative and quantitative evaluations of the material-mechanical characteristics are particularly important, and therefore must be included in process development. The present paper represents a methodology by which this can be achieved.

The Influence of Temperature on Low Cycle Fatigue Behavior of Prior Cold Worked 316L Stainless Steel (II) - Life Prediction and Failure Mechanism - (냉간 가공된 316L 스테인리스 강의 저주기 피로 거동에 미치는 온도의 영향 (II) - 수명예측 및 파손 기구 -)

  • Hong, Seong-Gu;Yoon, Sam-Son;Lee, Soon-Bok
    • Transactions of the Korean Society of Mechanical Engineers A
    • /
    • v.27 no.10
    • /
    • pp.1676-1685
    • /
    • 2003
  • Tensile and low cycle fatigue tests on prior cold worked 3l6L stainless steel were carried out at various temperatures ftom room temperature to 650$^{\circ}C$. Fatigue resistance was decreased with increasing temperature and decreasing strain rate. Cyclic plastic deformation, creep, oxidation and interactions with each other are thought to be responsible for the reduction in fatigue resistance. Currently favored life prediction models were examined and it was found that it is important to select a proper life prediction parameter since stress-strain relation strongly depends on temperature. A phenomenological life prediction model was proposed to account for the influence of temperature on fatigue life and assessed by comparing with experimental result. LCF failure mechanism was investigated by observing fracture surfaces of LCF failed specimens with SEM.

Creep Deformation Characteristics of Polycrystalline Ice and its Numerical Simulation in the Flow of Polar Glaciers (극지 빙하유동에 있어서 Polycrystalline Ice의 Creep 변형특성 수치 시뮬레이션)

  • 최경식
    • Journal of Korean Society of Coastal and Ocean Engineers
    • /
    • v.2 no.2
    • /
    • pp.59-66
    • /
    • 1990
  • Various types of ice distribution under low temperature greatly influence the environment of the Arctic and Antarctic Oceans. To understand fundamentals of ice properties such as Polar glaciers, icebergs and sea ice, this study focuses on the material behaviors and failure mechanisms of polycrystalline ice. Utilizing the continuum damage theory, a three-dimensional constitutive model to describe creep deformation characteristics in the glacial flow is developed in consideration of micro-cracking as the major physical process of ice deformation. The numerical model is compared with the published experimental data especially in uniaxial constant stress creep tests. The model can simulate primary and secondary creeps as well as tertiary creep characteristics due to the microcrack accumulation.

  • PDF

The hardness property for the contents of hydrogen of DLC coating deposited by PECVD (PECVD를 이용하여 증착시킨 DLC 코팅의 수소함유량에 의한 경도 특성)

  • Kim, Jun-Hyeong;Mun, Gyeong-Il;Park, Jong-Wan
    • Proceedings of the Korean Institute of Surface Engineering Conference
    • /
    • 2011.05a
    • /
    • pp.141-141
    • /
    • 2011
  • DLC(Diamond Like Carbon) 박막은 높은 경도, 낮은 마찰계수, 내화학성 등의 우수한 트라이볼로지적 특성을 가지고 있기 때문에 다양한 산업분야에서 적용되고 있다. 이러한 DLC 박막은 합성기구나 구조의 관점에서 몇 가지 다른 이름으로 불려지기도 한다. 밀도와 경도가 높기 때문에 경질탄소(Hard Carbon)라고도 불려지며, 수소를 함유한 경우에는 수소함유 비정질 탄소(Hydrogenated Amorphous Carbon)이라는 이름이 사용되며, 고밀도 탄소(Dense Carbon) 또는 고밀도 탄화수소(Dense Hydrocarbon)라고 불리기도 한다. 이렇듯 DLC 박막은 합성방법에 따라 함유된 수소와 탄소의 결합구조의 차이가 있다. 수소 함유한 DLC 박막은 20~50%까지 수소를 함유하며, DLC막의 기계적, 광학적, 전기적 특성들이 수소함량과 밀접한 관계를 가지고 있는 것으로 알려져 있다. 그러나 함유된 수소가 $300^{\circ}C$ 이상의 온도에서는 쉽게 결합에서 이탈되면서 흑연화와 더불어 마찰마모시 코팅층의 파손이 발생한다고 보고되고 있고, 또한 수소량이 증가함에 따라 DLC 박막의 경도는 감소하게 되는데, 이는 수소에 의해 dangling bond가 Passivation되면 탄화수소의 3차원적인 Crosslinking은 그만큼 감소하게 되기 때문이라고 알려져 있다. 본 연구에서는 PECVD를 이용하여 여러 가지 공정에 따른 DLC 박막을 증착시켰으며, 수소함유량에 따른 DLC막의 구조와 그에 따른 경도 변화를 살펴보았다. FTIR(Furier Transform Infrared Spectroscopy)과 Raman Spectroscopy을 이용하여 DLC막의 수소의 결합상태를 관찰하였으며, Nano Indentation을 사용하여 미소경도를 측정하였고, FE-SEM을 이용하여 표면과 단면을 관찰하였다. 막의 두께 측정에는 ${\alpha}$-Step을 사용하였으며, Ball-on-Disk 타입의 Tribo-meter을 이용하여, 모재의 경도에 따른 마찰계수 변화를 관찰하였다.

  • PDF

Risk Assessment Technique for Gas Fuel Supply System of Combined Cycle Power Plants (I) : Based on API RBI Procedures (복합화력발전의 가스연료 공급계통에 대한 위험도 평가 기법 연구 (I) : API RBI 절차에 기반한 위험도 평가)

  • Song, Jung Soo;Yu, Jong Min;Han, Seung Youn;Choi, Jeong Woo;Yoon, Kee Bong
    • Journal of Energy Engineering
    • /
    • v.27 no.2
    • /
    • pp.1-13
    • /
    • 2018
  • The proportion of natural gas-fueled power generation is expanding due to the change of domestic energy policy pursuing reduction of dust and increasing clean energy consumption. Natural gas fuels used for the combined-cycle power plants and the district-heating power plants are operated at high temperature and high pressure in the fuel supply system. Accidents due to leakage of the gas such as fire and explosion should be prevented by applying risk management techniques. In this study, risk assessment was performed on the natural gas fuel supply system of a combined power plant based on the API RP 581 RBI code. For the application of the API RBI code, lines and segments of the evaluation target system were identified. Operational data and input information were analyzed for the calculations of probability of failure and consequence of failure. The results of the risk assessment were analyzed over time from the initial installation time. In the code-based evaluation, the gas fuel supply system was mainly affected by thinning, external damage, and mechanical fatigue damage mechanisms. As the operating time passes, the risk is expected to increase due to the external damage caused by the CUI(Corrosion Under Insulation).

Assessment of System Reliability and Capacity-Rating of Composite Steel Box-Girder Highway Bridges (합성 강 상자형 도로교의 체계신뢰성 해석 및 안전도평가)

  • Cho, Hyo Nam;Lee, Seung Jae;Kang, Kyoung Koo
    • KSCE Journal of Civil and Environmental Engineering Research
    • /
    • v.13 no.2
    • /
    • pp.51-59
    • /
    • 1993
  • This paper develops practical and realistic reliability models and methods for the evaluation of system-reliability and system reliability-based rating of various types of box-girder bridge superstructures. The strength limit state model for box-girder bridges suggested in the paper are based on not only the basic flexural strength but also the strength interaction equations which simultaneously take into account flexure, shear and torsion. And the system reliability problem of box-girder superstructure is formulated as parallel-series models obtained from the FMA(Failure Mode Approach) based on major failure mechanisms or critical failure states of each girder. In the paper, an improved IST(Importance Sampling Technique) simulation algorithm is used for the system reliability analysis of the proposed models. This paper proposes a practical but rational approach for the evaluation of capacity rating in terms of the equivalent system-capacity rating corresponding to the estimated system-reliability index which is derived based on the concept of the equivalent FOSM(First Order Second Moment) form of system reliability index. The results of the reliability evaluation and rating of existing bridges indicate that the reserved reliability and capacity rating at system level are significantly different from those of element reliability or conventional methods especially in the case of highly redundant box-girder bridges.

  • PDF

Development of User Subroutine Program Considering Effect of Neutron Irradiation on Mechanical Material Behavior of Austenitic Stainless Steels (중성자 조사에 따른 오스테나이트 스테인리스 강의 기계적 재료거동 변화를 고려한 사용자 정의 보조 프로그램 개발)

  • Kim, Jong Sung;Jhung, Myung Jo;Park, Jeong Soon;Oh, Young Jin
    • Transactions of the Korean Society of Mechanical Engineers A
    • /
    • v.37 no.9
    • /
    • pp.1127-1132
    • /
    • 2013
  • The failure of reactor internals may have a significant effect on the safe operation and shutdown of a reactor. Various agings related to neutron irradiation occur or can potentially occur in the reactor internals owing to high neutron irradiation levels. Austenitic stainless steel, one of the principal materials constituting the reactor internals, shows different mechanical material behaviors such as tensile/creep properties and fracture toughness with neutron irradiation levels. This variation should be considered when the structural integrity of the reactor internals against agings during the design lifetime or continued operation period is evaluated. In this study, user subroutine programs considering the variation of mechanical material behaviors with neutron irradiation levels were developed. The programs were validated by testing them for various conditions.

A Study on the Crevice Corrosion for Ferritic Stainless Steel (페라이트 스테인리스강의 틈부식에 대한 연구)

  • Baik Shin-Young
    • Journal of the Korean Society of Marine Environment & Safety
    • /
    • v.10 no.1 s.20
    • /
    • pp.51-54
    • /
    • 2004
  • In recently days, the breed fish farm is increased in the beach side for farming fish. In such a farm, the heater is requested for preventing freezing in cold season. The heating material are requested high corrosion resistance and strength for endurance high corrosive salt and pressure. In case of low corrosion resistance and/or strength, the heating element shall be broke down and eventually make spillage or leaking contaminated salt. In the most cases, crevice corrosion is localized form of corrosion usually associated with a stagnant solution on the micro-environmental level. In this study, the crevice corrosion of Ferritic type 430 stainless steel is investigated. The size of specimen is $15{\times}20{\times}3mmt$. Test solution is 1N H2SO4 + 0.05N NaCl. The artificial crevice gap size is $0.24{\times}3{\times}15mmL$. Crevice corrosion is measured under applied voltage 300mV(SCE) to the external surface. the result of this study showed that 1) the induced time for initiation of crevice is 750seconds, 2) potential is dropped in the crevice from the top of gap opening from -320 to -399mV. The result confirmed that the potential drop(IR mechanism) in the crevice is one of mechanism for crevice corrosion.

  • PDF