• Computational Structural Engineering
• /
• v.4 no.4
• /
• pp.135-144
• /
• 1991

The finite element technique incorporatating infinite elements is applied to analyzing the general three dimensional wave-structure interaction problems within the limits of linear wave theory. The hydrodynamic forces are assumed to be inertially dominated, and viscous effects are neglected. In order to analyze the corresponding boundary value problems efficiently, two types of elements are developed. One is the infinite element for modeling the radiation condition at infinity, and the other is the fictitious bottom boundary element for the case of deep water. To validate those elements, numerical analyses are performed for several floating structures. Comparisons with the results by using other available solution methods show that the present method incorporating the infinite and the fictitious bottom boundary elements gives good results.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.25 no.3
• /
• pp.147-153
• /
• 2013

There exist various types of the WEC (Wave Energy Converter), and among them, the point absorber is the most popularly investigated type. However, it is difficult to find examples of systematically measured data analysis for the design of the point absorber type of power buoy in the world. The study investigates the wave load acting on the point absorber type resonance power buoy wave energy extraction system proposed by Kweon et al. (2010). This study analyzes the time series spectra with respect to the three-year wave data (2002.05.01~2005.03.29) measured using the pressure type wave gage at the seaside of north breakwater of Hupo harbor located in the east coast of the Korean peninsula. From the analysis results, it could be deduced that monthly wave period and wave height variations were apparent and that monthly wave powers were unevenly distributed annually. The average wave steepness of the usual wave was 0.01, lower than that of the wind wave range of 0.02-0.04. The mode of the average wave period has the value of 5.31 sec, while mode of the wave height of the applicable period has the value of 0.29 m. The occurrence probability of the peak period is a bi-modal type, with a mode value between 4.47 sec and 6.78 sec. The design wave period can be selected from the above four values of 0.01, 5.31, 4.47, 6.78. About 95% of measured wave heights are below 1 m. Through this study, it was found that a resonance power buoy system is necessary in coastal areas with low wave energy and that the optimal design for overcoming the uneven monthly distribution of wave power is a major task in the development of a WEF (Wave Energy Farm). Finding it impossible to express the average spectrum of the usual wave in terms of the standard spectrum equation, this study proposes a new spectrum equation with three parameters, with which basic data for the prediction of the power production using wave power buoy and the fatigue analysis of the system can be given.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.5
• /
• pp.331-339
• /
• 2020

In this study, ways to reduce the edge pressure at the bottom plate of the caisson breakwater were considered. The water depth, freeboard, design wave height and period, and the location of the center of gravity on the super-structure of the breakwater were selected as key design variables that influence the edge pressure, and analyzed how the edge pressure changes according to the change of this key variables. The pressure distribution formulae suggested in the design standard was applied for the calculation of design wave forces. Based on the wave forces, the required effective self-weight of the super-structure and the minimum width of the caisson were determined to have a safety factor of 1.2 against sliding and overturning. From the results, it was found that the edge pressure rapidly increased as the water depth increased, and could exceed the allowable bearing capacity when it reached a certain water depth which is 20 m within the analysis conditions. It was also confirmed that the edge pressure gradually increased linearly as the freeboard increased, but decreased with the increase of the wave height and period. This edge pressure could be significantly reduced up to more than 20% by moving the center of gravity of the super-structure to the seaside, which is 5% of the caisson width. Based on the analysis results and the recently conducted research results, a method was proposed to reduce the edge pressure that can be used in the design.

• Journal of Coastal Disaster Prevention
• /
• v.1 no.1
• /
• pp.28-35
• /
• 2014

This study investigated the applicability of four empirical equations (Morihira et al., 1967; Goda, 2010; Jensen, 1984 and Bradbury et al., 1988; Pedersen, 1996) suggested for estimating the horizontal wave force on the crown wall of sloping breakwaters. For the two exemplary cross sections of the breakwaters whose geometry are apparently different each other, the estimates of horizontal wave force calculated by the four equations were compared. The values of estimated wave force showed considerable discrepancy among the equations for each of the two exemplary breakwater cross sections, respectively. In addition, the relative magnitude of the wave force was quite different according to the breakwater geometry as well as the design wave condition. In general, Morihira's or Goda's formulae produced larger estimates of the horizontal wave force than Jensen/Bradbury's or Pedersen's formulae if the wave period (or wavelength) is comparatively short. In contrast, exactly opposite result was obtained when the wave period or wavelength is comparatively long. Further detailed study based on physical experiments is required to examine the applicability of the four empirical equations considered in this study more thoroughly.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.40 no.4
• /
• pp.360-366
• /
• 2004

This paper presents a method analyzing the motion of cylindrical buoy moored at 2 points and tensions action on each mooring line under the action of periodic waves. It was found that submersible buoy was more effective than floating one in the severe conditions considering its dynamic motions, wave forces, and mooring line tensions. The wave induced its dynamic responses and mooring line tensions peak when the ratio d/${\lambda}$ of the buoy length d to the waves length ${\lambda}$ was 0.66 due to its natural frequency. The results of this study were in agreement with the existing measurement ones, however, further verifications are needed considering resonance of cylindrical buoy and its displacements to wave height by a series of model tests.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.29 no.2
• /
• pp.83-91
• /
• 2017

In order to cope with the abnormally high waves during the storm surge due to climate change, various methods have been proposed for interlocking adjacent caissons to enhance stability of harbor structures. Among the methods, it was studied the method based on an open-cell caisson having reduction effect increasing the cohesion with adjunction caissons by filling materials such as crushed rocks in an inter-cell formed by two facing open-cells which consist of transverse walls. It is necessary to investigate the shear behaviors of an inter-cell to secure the stability using calculating shear forces on inter-cell under oblique wave loadings. It was analyzed the shear force share ratio with the length of internal and external wall and the number of internal walls. Numerical results show that 60~70% of the shear load is transmitted to adjacent caisson through the internal walls, more than 30% is through the external wall. It was applicable in the assumption that filling materials was uniformly distributed in inter-cells, and further studies were worth consideration on other conditions under construction.