• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.259-266
• /
• 2020

In this study, required drill bits and excavation methods were developed for an uneven drilling method that can solve the problem of performance degradation of rock bolts. The developed drill bit's excavation performance was verified using rock with a strength of 100 MPa or more. In addition, for the relative evaluation of the uneven excavation method, experimental specimens were prepared for models with and without irregularities, and tests were performed. As a result of the experiment, the model with unevenness exhibited an average critical draw resistance of 801.6 kN, which is about 1.7 times the value of 468.7 kN for the model without unevenness, thus confirming the effect sufficiently. Therefore, it is expected that the resistance performance will significantly increase despite an increase in the uneven hole diameter of 20 mm. In the future, the results of this study could be used as basic data when performing other studies using numerical analysis models and performance verification through experiments to obtain an optimized rock forming method.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.11
• /
• pp.109-117
• /
• 2007

Uncertainty is pervasive in rock slope stability analysis due to various reasons and subsequently it may cause serious rock slope failures. Therefore, the importance of uncertainty has been recognized and subsequently the probability theory has been used to quantify the uncertainty since 1980's. However, some uncertainties, due to incomplete information, cannot be handled satisfactorily in the probability theory and the fuzzy set theory is more appropriate for those uncertainties. In this study the random variable is considered as fuzzy number and the fuzzy set theory is employed in rock slope stability analysis. However, the previous fuzzy analysis employed the approximate method, which is first order second moment method and point estimate method. Since previous studies used only the representative values from membership function to evaluate the stability of rock slope, the approximated analysis results have been obtained in previous studies. Therefore, the Monte Carlo simulation technique is utilized to evaluate the probability of failure for rock slope in the current study. This overcomes the shortcomings of previous studies, which are employed vertex method. With Monte Carlo simulation technique, more complete analysis results can be secured in the proposed method. The proposed method has been applied to the practical example. According to the analysis results, the probabilities of failure obtained from the fuzzy Monte Carlo simulation coincide with the probabilities of failure from the probabilistic analysis.

• Explosives and Blasting
• /
• v.29 no.1
• /
• pp.10-16
• /
• 2011

To make large slopes or rock structures stable, supporting systems, such as anchor bolt, rock bolt and spiral bolt which are developed recently, are commonly used. In this study, in-situ pull-out tests were carried out to compare the characteristics of rock bolt that is most widely used with ones of spiral bolt that is newly developed. Re-pull-out test for the spiral bolt in which loading and unloading cycles are repeated three times showed that the maximum pull-out load is almost constant irrespective of the number of loading cycles, which may be due to no failure between spiral bolt and filler. On the other hand, the maximum pull-out load for the conventional rock bolt decreases with the number of loading cycles due to the partial failure between rock bolt and filler.

• The Journal of Engineering Geology
• /
• v.21 no.4
• /
• pp.295-304
• /
• 2011

The first step in improving our understanding of uncertainties suclt as rock mass strength parameters and deformation modulus in rock masses around high-level radioactive waste disposal repositories, for improved safety, is to study the process of crack development in intact rock. Therefore, in this study, the fracture process and crack development were examined in samples of KURT granite taken from the KAERI Underground Research Tunnel (KURT), based on acoustic emission (AE) and moment tensor analysis. The results show that crack initiation, coalescence, and unstable crack occurred at rock uniaxial compressive strengths of 0.45, 0.73, and 0.84, respectively. In addition, moment tensor analysis indicated that during the early stage of loading, tensile cracks were predominant. With increasing applied stress, the number of shear cracks gradually increased. When the applied stress exceeded the stress level required for crack damage, unstable shear cracks which directly result in failure of the rock were generated along the failure plane.

• The Journal of Engineering Geology
• /
• v.17 no.4
• /
• pp.545-554
• /
• 2007

Landslides is mainly induced by a heavy rainfall, earthquake ground motion, and some other factors like soil mechanics, morphological-geological factors etc. Since the starting point of the failure seemed to be originated at a construction site in the study, it is meaningful to find out the relationship between the landslide and the construction. For this study, the slope failure factor was examined carefully to see that the original natural slope had vulnerability and that the complex ground had unstability changed by construction. A field survey was conducted on the original ground surface and filled-up ground. A laboratory test was also conducted to determine the geomechanical properties of soil samples. 2D and 3D limit equilibrium analysis with changing groundwater level were conducted at the failure depth using a seismic refraction survey. The result shows that the factor of safety is similar stability under all condition, but unstable under saturated condition.

• The Journal of Engineering Geology
• /
• v.17 no.3
• /
• pp.381-391
• /
• 2007

A series of talus slope stability analyses were carried out using 2D FEM and 3D limit equilibrium methods for this study. The FEM analyses on Phase 2 were performed to delineate failure depths based on stress distributions for each slope. The results revealed that the failure surface exist in the colluvium layer of about 3-10 m thickness. Three dimensional models, derived from the FEM analyses and geological field survey, were made for the use in a 3D limit equilibrium analysis. The result shows that all the talus slopes are stable under dry condition, but unstable under saturated condition due to heavy rain.

• The Journal of Engineering Geology
• /
• v.25 no.1
• /
• pp.115-129
• /
• 2015

The cut-slope of a large-sectional tunnel portal is recognized as a potential area of weakness due to unstable stress distribution and possible permanent displacement. This paper presents a case study of a slope failure and remediation for a large-scale cut-slope at a tunnel portal. Extensive rock-slope brittle failure occurred along discontinuities in the rock mass after 46 mm of rainfall, which caused instability of the upper part of the cut-slope. Based on a geological survey and face mapping, the reason for failure is believed to be the presence of thin clay fill in discontinuities in the weathered rock mass and consequent saturationinduced joint weakening. The granite-gneiss rock mass has a high content of alkali-feldspar, indicating a vulnerability to weathering. Immediately before the slope failure, a sharp increase in displacement rate was indicated by settlement-time histories, and this observation can contribute to the safety management criteria for slope stability. In this case study, emergency remediation was performed to prevent further hazard and to facilitate reconstruction, and counterweight fill and concrete filling of voids were successfully applied. For ultimate remediation, the grid anchor-blocks were used for slope stabilization, and additional rock bolts and grouting were applied inside the tunnel. Limit-equilibrium slope stability analysis and analyses of strereographic projections confirmed the instability of the original slope and the effectiveness of reinforcing methods. After the application of reinforcing measures, instrumental monitoring indicated that the slope and the tunnel remained stable. This case study is expected to serve as a valuable reference for similar engineering cases of large-sectional slope stability.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.801-805
• /
• 2009

하천의 골재는 도로, 항만, 주택건설 등 다양한 건설재료로 이용되어 왔으며 급속한 산업화와 더불어 국가건설사업, 지방자치단체의 수익사업으로 인해 골재 수요가 급격히 증가해 왔다. 그러나 체계적인 조사 및 연구가 없이 무분별하게 행해진 하천준설은 하상저하, 하천의 불안정, 하상의 장갑화 등 물리적 영향뿐만 아니라 주변 하천의 식생, 저서생물의 서식처 등 수서생태계의 파괴, 하천정화능력 저하, 교각의 노출 등 생물적 경제적인 측면에서 악영향을 미치고 있다. 본 연구에서는 하천준설사업이 꾸준히 진행 중에 있는 낙동강 유역의 감천을 연구대상지역으로 선정하여, 2차원 수치모형인 RMA-2를 이용하여 준설에 따른 동수역학적 흐름특성의 변화를 모의하고, SED2D를 이용하여 단기하상변동을 예측하였다. 지형자료는 수치지도 및 실측자료를 토대로 하여 구축하였으며, 준설 전 후의 하상변동을 모의해 비교 분석한 결과, 하도중심에서의 흐름특성은 준설전에 비해 수위가 평균 0.85 m 저하되었고, 하상은 평균 0.56 m 저하되었다. 대상유역의 수위와 유속은 준설전에 비해 준설후에 안정적인 특성을 나타냈다. 또한, 준설전 후 전반적으로 하상상승이 발생하였으며 이는 상류에서의 유사유입량이 많아 퇴적이 많이 일어난 것으로 판단되며, 준설후는 준설전에 비해 하류에서의 퇴적량이 적게 나타났으며 이는 준설구간에서의 퇴적으로 인해 하류 유사이송이 적게 일어난 것으로 판단된다. 본 연구의 결과는 하천준설에 따른 하천환경 및 물리적 영향을 최소화하고, 교란하천의 복원 및 관리 등에도 활용될 수 있을 것이다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.1589-1593
• /
• 2008

하천의 골재는 도로, 항만, 주택건설 등 다양한 건설재료로 이용되어 왔으며 급속한 산업화와 더불어 국가건설사업, 지방자치단체의 수익사업으로 인해 골재 수요가 급격히 증가해 왔다. 그러나 체계적인 조사 및 연구가 없이 무분별하게 행해진 하천준설은 하상저하, 하천의 불안정, 하상의 장갑화 등 물리적 영향뿐만 아니라 주변 하천의 식생, 저서생물의 서식처 등 수서생태계의 파괴, 하천정화능력 저하, 교각의 노출 등 생물적 경제적인 측면에서 악영향을 미치고 있다. 본 연구에서는 하천준설사업이 꾸준히 진행 중에 있는 감천을 연구대상지역으로 선정하여, 1차원 수치모형인 Hec-ras4.0을 이용하여 준설량에 따른 흐름특성 및 교란된 하천의 적응과정을 분석하였다. 지형자료는 수치지도 및 실측자료를 토대로 하여 구축하였으며 장 단기 하상변동을 모의해 비교 분석하였다. 그 결과, 준설구간의 흐름특성은 준설전에 비해 수위가 감소되었고 하상변동은 준설구간의 상류부에서는 하상저하가 발생하였으며 하류부에서는 하상상승이 발생되었다. 본 연구의 결과는 하천준설에 따른 하천환경 및 물리적 영향을 최소화하고, 하천공사 실시와 수공구조물의 설계 및 유지관리 등에도 활용될 수 있을 것이다.

• Journal of Ocean Engineering and Technology
• /
• v.7 no.2
• /
• pp.57-67
• /
• 1993

The fracture behavior of plain woven glass/epoxy composite plates with a crack is investigated under static tensile loading. It is shown in this paper that the characteristic length associated with the point stress criterion depends on the crack length. To predict the not ched tensile strength, the point stress criterion proposed by Whitney and Nuismer are modified. An excellent agreement is found between the experimental results and the analytical prediction of the modified point stress criterion. The condition of unstable crack growth in the presence of a per-existing flaw(machined notch) is examined by means of the maximum stress intensity factor $K_max$ using maximumload P$_max$. The values of $K_max$ evaluated from energy release rate G$_max$(the compliance me thod) indicate a wide difference. Therefore in regard to anisotropy and heterogeneity of the composite materials studied, the modified shape correction factor f(a/W) is obtained. $K_max$evaluated by the compliance method a little or insignificantly depends on the initial crack length a, the specimen thickness B, the crack angle .theta. and the specimen geometry.