• Journal of Bio-Environment Control
• /
• v.18 no.4
• /
• pp.354-362
• /
• 2009

This study was performed to develop a suitable nutrient solution for standard rose substrate culture in a closed hydroponic system. 1/4, 1/2, 2/3 and 1 strength of the nutrient solution made by Japan National Institute of Vegetable and Tea Science (JNIVT) were supplied. The photosynthesis rate, quality and growth of cut flower were higher in the 1/2 and 2/3 strength of nutrient solution during high and low temperature period. Based on the above results, optimum nutrient solutions (UOS) were composed by nutrientwater (n/w) absorption ratio with 1/2S ($NO_{3^-}N$ 6.8, $NH_{4^-}N$ 0.7, $PO_{4^-}P$ 2.0, K 3.8, Ca 3.0, Mg 1.2, $SO_{4^-}S$ $1.2me{\cdot}L^{-1}$) at high temperature season and 2/3($NO_{3^-}N$ 9.7, $NH_{4^-}N$ 0.8, $PO_{4^-}P$ 2.2, K 5.0, Ca 3.9, Mg 1.5, $SO_{4^-}S$ $1.5me{\cdot}L^{-1}$) at low temperature season. The results of suitability examination showed that the EC level in newly composed nutrient solution (UOS) was more stable than other nutrient solutions due to its large amount of calcium and potassium. The growth of cut flower cultivated with UOS was higher than those of other nutrient solutions. Especially, the yield of cut flowers in UOS nutrient solution increased 1.4 times than that of other nutrient solution treatments. Consequently, the new nutrient solution investigated in this experiment was suitable for rose cultivation in a closed hydroponic system.

• Journal of Technology Innovation
• /
• v.26 no.3
• /
• pp.37-68
• /
• 2018

Since the 20th century, automobiles, which are the most common means of transportation, have been evolving as the use of electronic control devices and automotive semiconductors increases dramatically. Automotive semiconductors are a key component in automotive electronic control devices and are used to provide stability, efficiency of fuel use, and stability of operation to consumers. For example, automotive semiconductors include engines control, technologies for managing electric motors, transmission control units, hybrid vehicle control, start/stop systems, electronic motor control, automotive radar and LIDAR, smart head lamps, head-up displays, lane keeping systems. As such, semiconductors are being applied to almost all electronic control devices that make up an automobile, and they are creating more effects than simply combining mechanical devices. Since automotive semiconductors have a high data rate basically, a microprocessor unit is being used instead of a micro control unit. For example, semiconductors based on ARM processors are being used in telematics, audio/video multi-medias and navigation. Automotive semiconductors require characteristics such as high reliability, durability and long-term supply, considering the period of use of the automobile for more than 10 years. The reliability of automotive semiconductors is directly linked to the safety of automobiles. The semiconductor industry uses JEDEC and AEC standards to evaluate the reliability of automotive semiconductors. In addition, the life expectancy of the product is estimated at the early stage of development and at the early stage of mass production by using the reliability test method and results that are presented as standard in the automobile industry. However, there are limitations in predicting the failure rate caused by various parameters such as customer's various conditions of use and usage time. To overcome these limitations, much research has been done in academia and industry. Among them, researches using data mining techniques have been carried out in many semiconductor fields, but application and research on automotive semiconductors have not yet been studied. In this regard, this study investigates the relationship between data generated during semiconductor assembly and package test process by using data mining technique, and uses data mining technique suitable for predicting potential failure rate using customer bad data.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.1241-1245
• /
• 2006

절 성토사면에 구조물을 설치할 경우 가장 중요하게 고려되어야 하는 점은 사면의 안정성 여부이다. 특히, 절 성토사면에 설치된 구조물이 붕괴되는 가장 큰 원인은 뒷채움재 내에 존재하는 수압의 영향이라는 것을 우리는 이미 많은 연구와 경험을 통해 알고 있다. 만일 지하수위가 존재하는 상태에서 단시간에 발생되는 집중호우로 인해 수위가 갑자기 상승하였을 경우, 구조물을 통해 전혀 배수되지 않는다면 절 성토사면의 안정성은 급격히 저하될 것이다. 이러한 사면의 배수압을 소산시킬 수 있는 공법은 여러 가지가 있으나, 본 연구에서는 특히 제주도의 지역적 특성을 고려하여 화산석을 채움재로 사용한 Mattress/Filter를 절 성토사면에 설치함으로써 배수압을 소산시킬 수 있는 방법을 연구하였다. Mattress/Filter는 제방 또는 절 성토사면의 파괴와 침식을 방지하기 위해 사면에 설치하는 육각형의 철망구조로서 유연성, 다공성, 배수성 및 식생성과 같은 특징이 있으며, 콘크리트 구조물과 달리 별도의 배수시설을 필요로 하지 않는 장점이 있다. 또한 본 연구에 사용된 Mattress/Filter의 채움재인 화산석은 현재 제주도 지역에 방대하게 분포되어 있다. 특히 현무암은 제주도 암석 전체의 90%이상을 차지하고 있으며, 투수성이 매우 큰 암석이다. 현무암의 공극률은 그 종류에 따라 $0.02{\sim}0.36$의 범위로 나타난다. 특히, 표선리현무암의 경우 평균 공극률이 0.23으로 나타나 모래의 공극률인 $0.3{\sim}0.8$에 비교하여 볼 때, 연구에 사용된 재료는 아주 우수한 투수성을 가진 것으로 판명된다. 또한 현무암의 경우 암석의 겉 표면이 미세한 다공질 조직으로 이루어져 있다. 따라서 암석자체에 물이 정체될 수 있어 구조물을 통해 배수될 때 암석이 머금고 있는 물로 인해 추가적으로 발생하는 중력은 다른 재료가 가지지 못한 화산석의 또 다른 장점이라 할 수 있다.서는 자료변환 및 가공이 필요하다. 즉, 각 상습침수지구에 필요한 지형도는 국립지리원에서 제작된 1:5,000 수치지형도가 있으나 이는 자료가 방대하고 상습침수지구에 필요하지 않은 자료들을 많이 포함하고 있으므로 상습침수지구의 데이터를 인터넷을 통해 서비스하기 위해서는 많은 불필요한 레이어의 삭제, 서비스 속도를 고려한 데이터의 일반화작업, 지도의 축소.확대 등 자료제공 방식에 따른 작업 그리고 가시성을 고려한 심볼 및 색채 디자인 등의 작업이 수반되어야 하며, 이들을 고려한 인터넷용 GIS기본도를 신규 제작한다. 상습침수지구와 관련된 각종 GIS데이타와 각 기관이 보유하고 있는 공공정보 가운데 공간정보와 연계되어야 하는 자료를 인터넷 GIS를 이용하여 효율적으로 관리하기 위해서는 단계별 구축전략이 필요하다. 따라서 본 논문에서는 인터넷 GIS를 이용하여 상습침수구역관련 정보를 검색, 처리 및 분석할 수 있는 상습침수 구역 종합정보화 시스템을 구축토록 하였다.N, 항목에서 보 상류가 높게 나타났으나, 철거되지 않은 검전보나 안양대교보에 비해 그 차이가 크지 않은 것으로 나타났다.의 기상변화가 자발성 기흉 발생에 영향을 미친다고 추론할 수 있었다. 향후 본 연구에서 추론된 기상변화와 기흉 발생과의 인과관계를 확인하고 좀 더 구체화하기 위한 연구가 필요할 것이다.게 이루어질 수 있을 것으로 기대된다.는 초과수익률이 상승하지만, 이후로는 감소하므로, 반전거래전략을 활용하는 경우 주식투자기간은 24개월이하의 중단기가 적합함을 발견하였다. 이상의 행태적 측면과 투자성과측면의 실증결과를 통하여 한국주식시장에 있어서 시장수익률을 평균적으로 초과할 수 있는 거래전략은 존재하므로 이러한 전략을 개발 및 활용할 수 있으며, 특히, 한국주식시장에 적합한 거래전략은 반전거래전략이고, 이 전략의 유용성은 투자자가 설정한 투자기간보다 더욱 긴 분석기간의 주식가격정보에 의하여 최대한 발휘될 수 있음을 확인하였다.(M1), 무역적자의 폭, 산업

• The Korean Journal of Nuclear Medicine
• /
• v.37 no.5
• /
• pp.288-300
• /
• 2003

Purpose: To obtain regional blood flow and tissue-blood partition coefficient with time-activity curves from ${H_2}^{15}O$ PET, fitting of some parameters in the Kety model is conventionally accomplished by nonlinear least squares (NLS) analysis. However, NLS requires considerable compuation time then is impractical for pixel-by-pixel analysis to generate parametric images of these parameters. In this study, we investigated several fast parameter estimation methods for the parametric image generation and compared their statistical reliability and computational efficiency. Materials and Methods: These methods included linear least squres (LLS), linear weighted least squares (LWLS), linear generalized least squares (GLS), linear generalized weighted least squares (GWLS), weighted Integration (WI), and model-based clustering method (CAKS). ${H_2}^{15}O$ dynamic brain PET with Poisson noise component was simulated using numerical Zubal brain phantom. Error and bias in the estimation of rCBF and partition coefficient, and computation time in various noise environments was estimated and compared. In audition, parametric images from ${H_2}^{15}O$ dynamic brain PET data peformed on 16 healthy volunteers under various physiological conditions was compared to examine the utility of these methods for real human data. Results: These fast algorithms produced parametric images with similar image qualify and statistical reliability. When CAKS and LLS methods were used combinedly, computation time was significantly reduced and less than 30 seconds for $128{\times}128{\times}46$ images on Pentium III processor. Conclusion: Parametric images of rCBF and partition coefficient with good statistical properties can be generated with short computation time which is acceptable in clinical situation.

• Journal of Environmental Science International
• /
• v.7 no.6
• /
• pp.761-772
• /
• 1998

This study was performed to determine the optimum coagulant dosing amount for effective treatment of raw water. The removal rate of turbidity and the variations of water qualities according to various dosage of coagulants such as Alum, PAC and PACS were investigated. The optimum coagulant dosing amount to make the lowest turbidity of water were 35mg/ι t of Alum, 30mg/ι of PAC and 10mg/ι of PACS in case of 5 NTU of raw water turbidity, and 30mg/ι of Alum, 25mg/ι of PAC and 10mg/ι of PACS in case of 10 NTU of that, respectively. The removal rates of turbidity at 4 min. and 8 min. of settling time were 10 and 72% of Alum, 44 and 62% of PAC and 25 and 55% of PACS in case of 5 NTU, and 52 and 70% of Alum, 90 and 95% of PAC and 10 and 28% of PACS in case of 10 NTU, respectively. Judging from the settling capability of floc., the reaction time of floe. formation and removal efficiency of turbidity, PAC was evaluated as more effective coagulant than Alum and PACS. Also PAC was regarded as the most effective coagulant when the water supply was changed sharply and the fluctuation of the surface loading occured with wide and sharp in settling basin. pH and alkalinity of the water were decreased with increasing coagulants dosage. But pH and alkalinity were not decreased below 5.8 which is the standard for drinking water quality, and 10mg/ι which is the limit concentration of floc. breakage, respectively. Residual Al of the treated water was decreased with increasing coagulants dosage in case of 5 and 10NTU of raw water turbidity. $KMnO_4$ consumption of the water was decreased with increasing coagulants dosage. The reduction rate of $KMnO_4$ consumption at the optimum coagulants dosage were 39% of Alum. 18% of PAC and 11% of PACS in case of 5 NTU of raw water turbidity, and 42% of Alum, 27% of PAC and 36% of PACS in case of 10 NTU of that, respectively. Any relationship was not found between the removal rate of turbidity and KMnO$_4$ consumption. TOC of the water was a bit decreased with increasing coagulants dosage up to 30mg/ι but not changed above 30mg/ι of coagulants dosage. The degree of TOC reduction was increased in the order of Alum, PAC and PACS treatment. Zeta potential of the colloidal floe. at the optimum coagulants dosage was in the range of -20~-15mV in case of 5 NTU of raw water turbidity and 0~0.5mV in case of 10 NTU of that. respectively. Although the kinds and dosages of coagulants were different, zeta potential range were fixed under the conditions of the best coagulation efficiency.

• Microbiology and Biotechnology Letters
• /
• v.39 no.4
• /
• pp.382-386
• /
• 2011

Microbial fuel cells (MFC), devices that use bacteria as a catalyst to generate electricity, can utilize a variety of organic wastes as electron donors. The current generated may differ depending on the organic matter concentrations used, when other conditions, such as oxidant supply, proton transfer, internal resistance and so on, are not limiting factors. In these studies, a single-cathode type MFC (SCMFC) and dual-cathode type MFC (DCMFC) were used to ascertain the current's improvement through an increase in the contact area between the anode and the cathode compartments, because the cathode reaction is one of the most serious limiting factors in an MFC. Also an MFC was conducted to explore whether an improvement in electricity generation resulted from oxidizing the carbon sources and nitrates. About 250 mg $L^{-1}$ sodium acetate was fed to an anode compartment with a flow rate of 0.326 mL $min^{-1}$ by continuous mode. The current generated from the DCMFC was higher than the value produced from MFC with a single cathode. COD removal of dual-cathode MFC was also higher than that of single-cathode MFC. The nitrate didn't affect current generation at 2 mM, but when 4 and 8 mM nitrate was supplied, the current in the single-cathode and dual-cathode MFC was decreased by 98% from $5.97{\pm}0.13$ to $0.23{\pm}0.03$ mA and $8.40{\pm}0.23$ to $0.20{\pm}0.01$ mA, respectively. These results demonstrate that increasing of contact area of the anode and cathode can raise current generation by an improvement in the cathode reaction.

• Food Science and Preservation
• /
• v.17 no.1
• /
• pp.1-8
• /
• 2010

We investigated the effect of freezing on changes in the chemical components of semi-dried red pepper (SDRP). We used storage temperatures of $0^{\circ}C,\;-10^{\circ}C,\;-20^{\circ}C,\;and\;-70^{\circ}C$. After 30 days of storage, capsaicin content had decreased by 40% at $0^{\circ}C$ and by 21% at $-20^{\circ}C$. Initial vitamin C content was 1,358.02 mg%. Compared with control, the $0^{\circ}C$ storage group showed a significant decrease in vitamin C content but no such decrease was noted in the $-20^{\circ}C$ and $-70^{\circ}C$ storage groups after 30 days. ASTA values were not influenced by storage temperature or period, in agreement with previous results. We concluded that storage was effective at temperatures of less than $-20^{\circ}C$. Next, both dried red pepper (DRP) and SDRP were stored at $-20^{\circ}C$ for 12 months. DRP had the lower level of capsaicinoids (55.01 mg%) owing to the long drying time. After 12 months, SDRP capsaicinoid had decreased by 30-33%, compared with a decrease of 54% in DRP. Initial vitamin C contents were 721.48 and 955.25 mg% in DRP and SDRP, respectively, and, after 12 months, vitamin C loss in the SDRP group (37%) was less than that in fresh red pepper (FRP) samples (45%). Initial $\beta$-carotene content was greatest in the FRP group (259.82 mg%), and that of DRP decreased by 20% after 12 months. The color a/b value of SDRP (1.40) was greater than that of DRP (1.00).

• KSBB Journal
• /
• v.22 no.5
• /
• pp.305-312
• /
• 2007

It is crucial to develop a miniaturized cultivation method for large and rapid screening of high-yielding mutants of monacolin-K, a powerful anti-hypercholesterolemic secondary metabolite biosynthesized by the fungal cells of Monascus ruber. In order to investigate as many strains as possible in a short time, a miniaturized fermentation method especially suitable for the cultivation of the filamentous Monascus mutants was developed using $50m{\ell}$ culture-tube ($7m{\ell}$ of working volume) instead of the traditional $250m{\ell}$ flask ($50m{\ell}$ of working volume). Generally, in filamentous fungal cell fermentations, morphologies in growth and production cultures should be maintained as thick filamentous and compact-pelleted (usually less than 1 mm in diameter) forms, respectively, for enhanced production of secondary metabolites in final production cultures. In this study, we intended to induce the respective optimal morphologies in the miniaturized culture system for the purpose of rapid screening of overproducers. Miniaturized growth culture system was successfully developed due to the mass production of spores in the statistically optimized solid medium. When large amounts of spores were inoculated into the growth cultures, and brown rice flour (20 g/L) was also supplemented to the growth medium, dense filamentous morphologies were successfully induced in the growth cultures performed with the 50 ml culture tubes. It was implied that the amounts of spores inoculated into the growth tube-cultures and the growth medium components should be the key factors for the induction of the filamentous forms in the growth fermentations. Furthermore, in order to statistically optimize production medium, multiple experiments based on Plackett-Burman design and response surface method (RSM) were carried out, resulting in more than 2 fold enhanced production of monacolin-K in the final production cultures with the optimized production medium. Notably, under the production culture conditions with the statistically optimized medium, optimal pellet sizes below 1 mm in diameter were reproducibly induced, in contrast to the thick and viscous filamentous morphologies observed in the previous production cultures.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.9 no.2
• /
• pp.201-219
• /
• 2014

The Republic of Korea in the real economy to a knowledge economy, and a center of creativity and imagination in the creative economy is changing the paradigm. As the core of creating economic, creative industries with the technology and information play an important role in the industry individuals. In order to solve the problem of the polarization of the economy and high youth unemployment rate of Korea, to recognize the role of the creative industries, as objection part, dimensions pan-national and one creative companies in industries of Mobile Apps various policies that support has been promoted. Support these policies to be able to contribute to the establishment of the success of mobile apps one-person creating company, we performed this study targeting one-person company that creates mobile apps area, we conducted a demonstration study of success factors, and thus more effective and efficient in an attempt to seek out support measures. In this study, we derive a research 4 hypothesis about the success factors of one creative enterprise through literature discussion, a study was made on the basis of empirical data of one-person company that creates mobile apps. The results of the analysis, first, if the development rate of the mobile application technology is fast and a new competition associated product is appeared, it was possible to find a tendency to be higher at the performance quantitative companies. Second, if the founder is a founding for the benefit and rewarding work and come to terms with the risk, it was possible to discover tends to be higher achievement quantitative. Third, if one-person company select a target market with capture intensively, it was possible to find a tendency for higher qualitative results. Fourth, it could be found that the reliability of the contact frequency of the network related performance business environment these characteristics enterprise management strategy and act as a significant modulatory effect. Provision of information relating to management and entrepreneurship education to be one creative enterprise is required, these results suggest that there is a provision continuing need for the opportunity to be able to meet and network and reliable variety have. In this study, to take advantage to promote the elimination measures that can increase the likelihood of success of the company of institutions to support one company that creates knowledge-based, such as in the field of mobile application.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.3
• /
• pp.3-9
• /
• 2017

Recently, in 3rd Generation Partnership Project(3GPP), there is a study of the Long Term Evolution(LTE) based vehicle communication which has been actively conducted to provide a transport efficiency, telematics and infortainment. Because the vehicle communication is closely related to the safety, it requires a reliable communication. Because vehicle speed is very fast, unlike the movement of the user, radio channel is rapidly changed and generate a number of problems such as transmission quality degradation. Therefore, we have to continuously updates the channel estimates. There are five types of conventional channel estimation scheme. Least Square(LS) is obtained by pilot symbol which is known to transmitter and receiver. Decision Directed Channel Estimation(DDCE) scheme uses the data signal for channel estimation. Constructed Data Pilot(CDP) scheme uses the correlation characteristic between adjacent two data symbols. Spectral Temporal Averaging(STA) scheme uses the frequency-time domain average of the channel. Smoothing scheme reduces the peak error value of data decision. In this paper, we propose the novel channel estimation scheme in LTE based Vehicle-to-Vehicle(V2V) environment. In our Hybrid Reliable Channel Estimation(HRCE) scheme, DDCE and Smoothing schemes are combined and finally the Linear Minimum Mean Square Error(LMMSE) scheme is applied to minimize the channel estimation error. Therefore it is possible to detect the reliable data. In simulation results, overall performance can be improved in terms of Normalized Mean Square Error(NMSE) and Bit Error Rate(BER).