• Journal of the Korea Concrete Institute
• /
• v.13 no.2
• /
• pp.130-138
• /
• 2001

This paper presents on the shear behavior prediction of reinforced concrete beams using Transformation Angle Truss Model (TATM). The TATM can evaluate the stress-strain relationships for cracked concrete by transforming stresses and strains for principal plane into those over the crack surfaces. This proposed analytical method simplifies the Fixed Angle Softened Truss Model (FA-STM) and removes the limitation of applicability of the FA-STM. The shear.strength and strain of reinforced concrete beams are predicted by using the TATM. For the verification of proposed method, experimental results of reinforced concrete beams were compared with theoretical results by the TATM, FA-STM and Rotating Angle Softened Truss Model (RA-STM).

• Magazine of the Korea Concrete Institute
• /
• v.10 no.1
• /
• pp.4-9
• /
• 1998

• Magazine of the Korea Concrete Institute
• /
• v.10 no.1
• /
• pp.32-39
• /
• 1998

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.143-146
• /
• 2005

최근 들어 90도 표준갈고리의 대안으로 정착판을 지니는 헤드 철근(headed bar)에 대한 관심이 높아지고 있다. 헤드 철근의 정착내력은, 정착판의 지압력과 위험단면에서 헤드까지 정착길이의 부착력으로 발현된다. 실제 구조물에서는 정착되는 부재의 재료 및 기하학적 물성에 의해 다양한 파괴가 발생된다. 따라서 헤드 철근의 정착내력은 단순히 지압력과 부착력의 합으로 산정될 수 없으며, 발생 가능한 모든 파괴양상을 고려한 최소 내력으로 결정되어야 한다. 헤드 철근의 정착내력을 산정하기 위한 기본적인 해석모델로, CCT 절점에 정착된 헤드 철근의 트러스 모델을 제안하였다. 제안된 트러스 모델의 파괴는 부착파괴와 콘크리트의 압축파괴로 구분되며, 재료 및 기하학적 물성에 의해 파괴 양상이 결정된다. 이러한 트러스 모델은 외부 보-기둥 접합부와 같이 보다 복잡한 부위에 정착된 헤드철근의 정착 기구를 설명하는데 활용될 수 있다.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.3
• /
• pp.377-387
• /
• 2008

The post-buckling behavior of slender members, such as the chord of truss structures generally implies extreme strength degradation. The buckling strength is usually determined as the performance of the compressed steel members, so it is important to understand the exact buckling behavior of a member in order to design the entire structure. A target analytical model is usually divided by beam or shell element when we simulate the buckling behavior of a compressed steel member such as atruss member. In this case, it is possible to accurately obtain the behavior, but such would be expensive and would require experience inanalysis even in monotonic loading. In this paper, we propose a consistent and convenient method to analyze the post-buckling behavior of elastoplastic compression members. The present methods are formulated to satisfy the second law of thermodynamics. Three numerical examples were tested to determine the validity of the proposed model in cyclic loading with comparable F.E.M results.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.1
• /
• pp.10-19
• /
• 1998

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05d
• /
• pp.215-222
• /
• 1996

원전 격납구조물의 구조해석에 대한 대부분의 연구에서 격납구조물을 축대칭으로 모델하고 있다. 따라서 격납구조물에 배근된 강재도 축대칭으로 가정하는 것이 일반 적이며, 유한요소모델 구성시 강재는 2절점 트러스나 1절점 링 트러스요소에 의해서 모델한다. 이때 유효철근비는 트러스요소의 단면적에 의해서 표현되며, 원통형 벽체에서는 높이에 따라 배근된 강재량이 일정하므로 실제와 근접한 모델이 가능하다. 그러나, 상부돔의 축대칭모델시 돔의 자오선 방향으로 규정된 강재량이 일정치 않고, 변화하게 된다. 기존에 연구에서는 이러한 강재량의 변화를 고려하지 못하고 반경방향으로 일정한 것으로 가정하여 구조해석을 수행하여 왔다. 이와같은 모델상의 제약으로 인해서 철근이나 텐던의 조기항복, 돔 정상부 부근에서의 부 정확한 변형특성을 보이고 있다. 본 연구에서는 실제 규정된 강재량을 유한요소모델에 반영하기 위해 정점부에서 자오선 방향으로 변화되는 강재량을 모델할 수 있는 기법에 대해서 연구하였으며, 연구결과를 바탕으로 격납구조물의 극한 내압해석을 수행하여 기존 모델방법에 의한 해석결과와 비교하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.2A
• /
• pp.187-196
• /
• 2008

The punching shear strength of RC slabs is estimated analytically by the simple truss model. To avoid intrinsic difficulties in punching shear analysis of reinforced concrete slabs, the slabs were divided into three sub-structures as the punching cone and the remaining parts. The strength of the punching cone was evaluated by the stiffness of inclined strut. The stiffness of springs which control lateral displacement of the roller supports consists of the steel reinforcement which passed through the punching cone. Initial angle of struts was determined by curve fitting method of the experimental data with variable reinforcement ratio in order to compensate for uncertainties in the slab's punching shear, the simplification errors and the stiffness of the remaining sub-structures. The validity of computed punching shear strength by simple truss model was shown by comparing with experimental results. The punching shear strength, which was determined by snap-through critical load of shallow truss, can be used effectively to examine punching shear strength of RC slabs.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.4
• /
• pp.367-381
• /
• 2007

A transmission tower was designed using the structural methodology to assume a simple truss behavior. However, there is a big difference between a simple truss behavior and a real one. A suitable explanation of structural stability is that it is a semi-rigid connection and not the assumed hinged connection. This study proposes an alternative structural-analysis modeling strategy for the transmission tower design. The element models that were considered were the truss element model, the beam element model, and the combined beam-truss element model. This study includes linear static analysis, free-vibration analysis, and elastic buckling analysis with respect to the design load. The results of the analysis indicate that the axial forces, axial stresses, and maximum displacements of the three analytical models are very similar. However, the bending moments and stresses of the beam element model and of the combined beam-truss element model are significantly high. The results of the free-vibration and elastic buckling analyses show that the beam-truss model can be conservatively used for the transmission tower design.

• Journal of Korean Association for Spatial Structures
• /
• v.5 no.2 s.16
• /
• pp.89-97
• /
• 2005

As building structures are becoming high-rise, large-scale, and specialized, the use of high-strength materials increase. Therefore, an analytical model is necessary to appropriately predict the shear strength of reinforced concrete (RC) beams with high-strength materials. This study presents a truss model which is able to reasonably predict the shear strength of the RC beams having high-strength steel bars. Test results of 107 RC beams reported in the technical literatures were collected to check the validity of proposed model, TATM, for the shear strength of the RC beams with high-strength reinforcing bars. They were compared to theoretical results obtained from proposed model, TATM, and existing truss models. The experimental results were better predicted by TATM rather than other truss models, and the ratios of experimental results to theoretical results obtained from TATM were almost constant regardless of the yield strengths of tension and shear reinforcements.