• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.2
• /
• pp.152-161
• /
• 2011

An interior permanent magnet synchronous motor(IPMSM) has been applied to the electric vehicle due to its high efficiency, compact volume, and wide operating speed ranges. This paper presents the analysis of the flux weakening operating regions at high speeds for the IPMSM that has back emf harmonics. The effect of the back emf harmonics on the motor speed and the maximum torque is analyzed. Also the dq currents for maximum torque operation under the voltage and the current limit conditions are analyzed. The conventional analysis and the presented analysis for the flux weakening operating regions are compared and the maximum torque - speeds characteristics for both analysis are verified through the experiment.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.5
• /
• pp.321-328
• /
• 2015

In recent years, there has been an increasing demand to apply the new IACS(International Association of Classification Societies) standards for ice and polar-classed ships. For ice-class vessel propulsion system, the ice impact torque design criterion is defined as a periodic harmonic function in relation to the number of the propeller blades. However, irregular or transient ice impact torque is assumed to occur likely in actual circumstances rather than these periodic loadings. In this paper, the reliability and torsional vibration characteristics of a comparatively large six-cylinder marine diesel engine for propulsion shafting system was examined and reviewed in accordance with current regulations. In this particular, the transient ice impact torque and excessive vibratory torque originating from diesel engine were interpreted and the resonant points identified through theoretical analysis. Several floating ice impacts were carried out to evaluate torque responses using the calculation method of classification rule requirement. The Newmark method was used for the transient response analysis of the whole system.

• Composites Research
• /
• v.19 no.3
• /
• pp.29-36
• /
• 2006

Since composite materials have anisotropic properties that depend on their stacking angle and sequence, the analysis of joints with isotropic adherends is limited in describing the behavior of the adhesive Joint with composite adherends. In this study, the nonlinear solution for adhesive joints with composite adherends was derived by incorporating the nonlinear behavior of the adhesive into the analysis. The behavior of the laminated composite tube was first analyzed, and the stress distributions of the composite tubular adhesive joint were calculated by including the nonlinear properties of the adhesive. The effect of the stacking sequence of composite adherends and bonding length on torque capacities of joints was examined, and results of the nonlinear analysis were also compared with those of the linear analysis.

• Electrical & Electronic Materials
• /
• v.11 no.11
• /
• pp.118-121
• /
• 1998

• Proceedings of the Korean Magnestics Society Conference
• /
• 1991.11a
• /
• pp.32-35
• /
• 1991

• Proceedings of the Korean Magnestics Society Conference
• /
• 1999.10a
• /
• pp.142-143
• /
• 1999

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.112-118
• /
• 2004

Recently, development of rare earth permanent magnet with the high remanence, high coercivity allows the design of brushless motors with very high efficiency over a wide speed range. Cogging torque is produced in a permanent magnet by magnetic attraction between the rotor mounted permanent magnet and the stator teeth. It is an undesired effect that contributes to output ripple, vibration, and noise of machine. This cogging torque can be reduced by variation of magnet arc length, airgap length, magnet thickness, shifting the magnetic pole and varying the radial shoe depth and etc. In this paper, some airgap length and magnet arc that reduce cogging torque are found by finite element method(FEM) and Maxwell stress tensor method. The SPM(Surface Permanent Magnet) type of high-power Brushless DC (BLDC) motor is optimized as a sample model.

• Journal of Aerospace System Engineering
• /
• v.13 no.3
• /
• pp.1-8
• /
• 2019

The electromagnetic forces generate a torque on the gimbal motor, and changes in the coil current causes torque ripple. This affects the gimbals' speed and results to unstable satellite attitude. It is therefore essential to reduce the torque ripple of the gimble motor with the aim of improving the attitude control accuracy of the satellite. This paper theoretically analyzes the torque generated from the modeling of a motor for general concentrated winding and distributed winding. The prototype was designed and fabricated through selection of the winding that reduces the torque ripple through simulation results. The results of the magnetic fields' theoretical analysis and the back electromotive force of the prototype were compared with the calibrated results for verification of conformity and manufacture of the design. The low-speed test proved that the torque ripple is reduced by improving the speed stability.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.407-408
• /
• 2016

본 논문에서는 26kW 매입형 영구자석형 동기식 모터를 적용한 빌트인 스핀들 주축에 관한 내용을 다룬다. 적용된 모터는 코깅토크 및 토크리플 최소화를 위한 비균일 공극 및 W타입 영구자석 배치를 적용하고 있으며, 관련된 특성해석결과 및 제작모델의 부하조건에 따른 속도 제어 특성에 대하여 다룬다.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1105-1106
• /
• 2011

본 논문에서는 EV 구동용 유도전동기와 매입형 영구자석 동기전동기(IPMSM)의 동작특성과 효율을 비교하기 위하여 농형구조 유도전동기와 단층구조 IPMSM을 설계 하였다. EV 구동용 전동기는 정속운전 뿐만 아니라 가변속 운전이 필수적이므로 유도전동기는 V/f 제어, IPMSM은 약계자 제어를 사용하여 가변속 상태에서의 운전토크와 효율을 유한요소법을 이용하여 해석하였다.