• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.2
• /
• pp.145-150
• /
• 2010

This paper deals with reduction of torque ripple in a brushless DC motor with input voltage control. The commutation torque ripple can be controlled with varying input voltage, but cogging torque is independent on it. So, in this paper a strategy for minimizing torque ripple is proposed by offsetting the cogging torque with deliberate voltage control. The optimal condition is determined with variable voltage levels and advance angles. As results, it is shown that the method causes 63% decrease of torque ripple.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1087-1089
• /
• 2003

This paper presents a method to reduce commutation torque ripple in a sensorless brushless DC motor drive without current sensors. To compensate the commutation torque ripple completely, the duration of commutation must be known. The proposed method measures the duration of commutation from terminal voltage waveforms, calculates a PWM duty ratio to suppress the commutation torque ripple from the output of speed controller, and applies the calculated PWM duty ratio only during the commutation. Experimental results show that vibrations are considerably reduced when the proposed method is applied to the sensorless brushless DC moter drive for air-conditioner compressor.

• Proceedings of the KIEE Conference
• /
• 2009.04b
• /
• pp.100-102
• /
• 2009

밴드패스필터를 사용하여 센서리스 벡터제어에 영향을 주는 6차고조파 성분을 제거하여 안정적인 제어를 제안하였다. 비정현적인 역기전력을 가진 IPMSM모터의 센서리스 벡터 제어에서 유기전압에 고조파가 포함되는 경우에 그 영향이 추정연산에 나타나게 된다. 삼상 모델에 나타나는 5차, 7차 고조파의 경우는 d, q축 모델로 변환 시 6차 고조파 성분으로 나타나게 된다. 이 6차 고조파 성분은 위치 추정과 속도추정에 영향을 주어서 토크 맥동을 발생시킨다. 본 논문에서는 이러한 6차 고조파의 영향으로 추정연산에 미치는 영향들을 알아보고. 이 영향을 고조파 제거를 위한 복잡한 계산을 하지 않으면서 간단한 밴드패스필터를 통해 고조파가 위치추정에 미치는 영향을 최대한 줄이는 방법을 제시하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.1
• /
• pp.101-109
• /
• 2000

Mutual torque ripple in a brushless DC motor is the main source of acoustic noise, especially fur motor operation with high speed and torque. This paper presents a method to obtain mutual torque ripple to identify acoustic noise source. Mutual torque ripple can be determined by analyzing phase current shape and magnetic circuit with different lead angles. Current shape is determined by state space model of voltage equation with the use of inductance calculated by FEM, and confirmed by experimental results. Mutual torque ripple is also determined by FEM analysis for the calculated current shape. Acoustic noise experiment reveals that mutual torque ripple with different lead angle is one of the main sources for noise generation in a brushless DC motor.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.2
• /
• pp.191-201
• /
• 2001

Recently, the demand of motor for industrial, household machinery is increasing. As Switching devices and control technology are progressing, so the use of BLDC Motor is increasing. But 3-Phase BLDC Motor generally used has pulsating torque and speed variation in commutation, so the range of its application is limited to high speed operation. Especially, to solve these problems, it is necessary to increase phase of Motor, so study of Poly-Phase BLDC Motor is progressing. However, when hysteresis current controller is used, switching frequency is highly increasing. In this paper, 7-Phase BLDC Motor drive system is designed. Also MSTC(Minimum Switching Time Controller) is proposed and with simulation and experiment, there validities are verified.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1077-1079
• /
• 2005

최근 산업기기의 대형화로 인하여 전기기기 및 전력기기의 고효율 대용량 설계에 대한 관심이 커지고 있다. 그 동안에는 대용량 전동기로 주로 유도전동기와 릴럭턴스 전동기가 사용되어 왔다. 그러나 유도전동기는 저속에서의 효율이 낮으며 회전자의 열손실이 효율과 역률을 저하시키는 단점이 있고, 릴럭턴스 전동기는 구조 및 동작원리 상 큰 맥동토크로 인하여 소음과 진동이 매우 크다. 이에 효율과 역률이 좋고 고속운전이 가능한 영구자석형 전동기에 대한 연구가 많이 진행되었고 최근에는 영구자석 재질(희토류계)의 발달함로 인하여 고속 대용량 자석계자형 BLDC와 영구자석형 동기전동기의 설계가 가능해져 대형기에 많이 이용되고 있다. 그러나 대용량 전기기기의 경우 그 크기와 부피가 매우 크고 대전류 대전압의 전원을 공급하여야 하기 때문에 인버터부를 병렬 연결하여야 하므로 제어부를 포함한 전동기의 설치 공간이 증가해 지는 단점이 있다. 이에 본 연구에서는 인버터를 전동기의 회전자 내부에 배치한 인버터 내부형 5[MW]급 BLDC 전동기를 설계하고자 하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.4
• /
• pp.164-172
• /
• 2020

The fuel oil/heat exchanger installed in military aircraft is a device that cools the lubricant oil supplied to other devices, such as an AMAD, and a hydraulic pump using the low temperature of the fuel is cracked at the AMAD lubricant inlet port. If a crack in the heat exchanger occurs, the lubricant oil supplied to other equipment is not cooled. Therefore, the flight can no longer be performed. In this study, non-destructive inspection and microscopic examination of the fracture surface of the oil port were performed to analyze the crack tendency. The oil pipe connected to the oil port is a titanium pipe, which is fastened with over torque and has been identified as the leading cause of heat exchanger oil port cracks. In addition, it was verified as the main reason for cracking by finite element analysis. The material and diameter of the pipe were changed to improve this defect, and the applied torque was adjusted. In addition, the bending value of the pipe was adjusted to minimize the fatigue accumulation due to pulsating pressure. As a result, no cracks occurred on the heat exchanger via the ground test after the installation of an improved pipe under the same conditions.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.4
• /
• pp.22-29
• /
• 2002

Usually, much harmonics are included and cause harmonic loss of motor, torque pulsation, electro-magnetic noise and shock etc. by switching function of inverter when drive induction motor variableness inside. It applied partial resonant Buck converter and three phase voltage type SPWM inverter circuit to induction motor driving system in this paper that see to solve such problem. Changed operation condition variously to do input current of circuit that propose sine-wave by unit power factor almost and capacitor supplied bringing back to life voltage by power supply arranging properly assistance diode and electric power switching. Power factor and efficiency improved as that minimize variation of input at power supply voltage polarity reverse by that add voltage reversal function. Also, by using output filter, reduced harmonic of output line to line voltage components, and introduce state space analysis and forecast operation of rectifier. Such all items confirmed validity through simulation and an experiment.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.1
• /
• pp.52-60
• /
• 2005

Generally, a voltage difference or voltage distortion exists between the reference voltage and the practical voltage applied to a motor in a pulse width modulated(PWM) voltage source inverter(VSI). This voltage distortion varies with the operating conditions such as the temperature, DC link voltage, and phase current level. Also the voltage distortion affects the machine current distortion, torque pulsations, and control performance. In this paper, the voltage distortion in a PWM VSI is analyzed and a new on-line estimation method based on the model reference adaptive system(MRAS) is proposed to compensate the time varying voltage distortion, while considering the parameter variations for a permanent magnet synchronous motor (PMSM). The simulation and experimental results show the effectiveness of the proposed voltage difference observer and the compensation method.