• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.185-185
• /
• 2004

최근 고속 회전기계에 사용되고 있는 공기호일 베어링은 동압형 기체 베어링으로 매우 안정적이고, 보통의 저널 베어링에서 발생할 수 있는 불안정한 진동을 최소화 할 수 있는 장점을 가지고 있다. 또한 높은 안정성 및 축 자체에 자동 조절 기능을 가지고 있어서 극저온 기계 및 고속 회전기계에 널리 사용되고 있다. 이러한 고속 회전기계는 축의 기동 및 정지 시, 위험속도를 안전하게 통과하기 위해 위험속도에서의 진동을 억제하여야 하고, 운전 가능한 회전수를 증가시키기 위해서 로터 시스템의 동적 해석이 필요하다.(중략)

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.4
• /
• pp.293-301
• /
• 2017

A Sub-kWe small-scale experimental test loop was manufactured to investigate characteristics of the supercritical carbon dioxide power cycle. A high-speed turbo-generator was also designed and manufactured. The designed rotational speed of this turbo-generator was 200,000 rpm. Because of the low expansion ratio through the turbine and low mass flowrate, the rotational speed of the turbo-generator was high. Therefore, it was difficult to select the rotating parts and design the turbine wheel, axial force balance and rotor dynamics in the lab-scale experimental test loop. Using only one channel of the nozzle, the partial admission method was adapted to reduce the rotational speed of the rotor. This was the world's first approach to the supercritical carbon dioxide turbo-generator. A cold-run test using nitrogen gas under an atmospheric condition was conducted to observe the effect of the partial admission nozzle on the rotor dynamics. The vibration level of the rotor was obtained using a gap sensor, and the results showed that the effect of the partial admission nozzle on the rotor dynamics was allowable.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.4
• /
• pp.326-335
• /
• 2014

Aerodynamic characteristics of the small two-stage turbo blower were investigated using commercial CFD tool(ANSYS CFX Ver. 14.5) in this paper. Turbo blower, which is a centrifugal type of turbomachinery, is used in various industries. It is used for application that required high static pressure rising at relatively small volumetric flow rate. In order to understand the mechanism of static pressure rising, the aerodynamic characteristics of the small two-stage turbo blower are analyzed at high rotating speed in this study. The k-${\omega}$ SST turbulence model, which is good at prediction of adverse pressure gradient flows, was applied. The CFD results of the turbo blower are validated by performance test. The static pressure rising of the turbo blower is nonlinearly increased over the first stage and the second stage. The secondary flow occurred at guide vanes, between the casing and the first impeller shroud, and the bottom of the impeller disk. As a result, It is required that whole fluid area is analyzed to predict aerodynamic characteristics of small two-stage turbo blower. and the result should be selected with considering for error from experiment and CFD.

• Tribology and Lubricants
• /
• v.37 no.3
• /
• pp.91-98
• /
• 2021

This paper presents a hydrostatic bearing design and rotordynamic analysis of a turbo expander for a hydrogen liquefaction plant. Th~e turbo expander includes the turbine and compressor wheel assembled to a shaft supported by two hydrostatic radial and thrust bearings. The rated speed is 75,000 rpm and the rated power is 6 kW. For the bearing operation, we use pressurized air at 8.5 bar as the lubricant that is supplied to the bearing through the orifice restrictor. We calculate the bearing stiffness and flow rate for various gauge pressure ratios and select the orifice diameter providing the maximum bearing stiffness. Additionally, we conduct a rotordynamic analysis based on the calculated bearing stiffness and damping considering design parameters of the turbo expander. The predicted Cambell diagram indicates that there are two critical speeds under the rated speed and there exists a sufficient separation margin for the rated speed. In addition, the predicted rotor vibration is under 1 ㎛ at the rated speed. We conduct the operating test of the turbo expander in the test rig. For the operation, we supply pressurized air to the turbine and monitor the shaft vibration during the test. The test results show that there are two critical speeds under the rated speed, and the shaft vibration is controlled under 2.5 ㎛.

• Journal of the Korean Institute of Gas
• /
• v.18 no.5
• /
• pp.85-90
• /
• 2014

Turbo chiller is widely used for the air conditioner and uses hydrochlorofluorocarbon 123 (HCFC-123) as a refrigerant. HCFC-123 is one of the chemicals being considered as a replacement for the chlorofluorocarbons. High concentrations of HCFC-123 cause a deficiency of oxygen with the risk of unconsciousness or death, the vapour is heavier than air and may accumulate in low ceiling spaces causing deficiency of oxygen. In this study, the concentration distribution of oxygen indoor was investigated by using computational fluid dynamics(CFD) as four workers were killed in HCFC-123 gas leaks at machine room of hypermarket in 2011.

• Tribology and Lubricants
• /
• v.38 no.2
• /
• pp.33-40
• /
• 2022

In this study, we present rotor dynamic analysis and operation test of a turbo expander for a hydrogen liquefaction plant. The turbo expander consists of a turbine and compressor wheel connected to a shaft supported by two hydrostatic radial and thrust bearings. In rotor dynamic analysis, the shaft is modeled as a rigid body, and the equations of motion for the shaft are solved using the unsteady Reynolds equation. Additionally, the operating test of the turbo expander has been performed in the test rig. Pressurized helium is supplied to the bearings at 8.5 bar. Furthermore, we monitor the shaft vibration and flow rate of the helium supplied to the bearings. The rotor dynamic analysis result shows that there are two critical speeds related with the rigid body mode under 40,000 rpm. At the first critical speed of 36,000 rpm, the vibration at the compressor side is maximum, whereas that of the turbine is maximum at the second critical speed of 40,000 rpm. The predicted maximum shaft vibration is 3 ㎛, whereas sub-synchronous vibration is not presented. The operation test results show that there are two critical speeds under the rated speed, and the measured vibration value agrees well with predicted value. The measured flow rate of the helium supplied to the bearing is 2.0 g/s, which also agrees well with the predicted data.

• Journal of the KSME
• /
• v.30 no.6
• /
• pp.564-571
• /
• 1990

최근의 기관은 DOHC 또는 SOHC로 4밸브나 5밸브를 채용하여 흡기계의 효율향상을 시도하고 있다. 그러나 고속성능에 중점을 두고 기관제원을 설정하게 되면서 저속 실용역에서 토크의 저하를 초래하는 경우가 많아지고 있으며 금후 이러한 문제의 해결에 많은 노력이 계속될 것으로 전망된다. 또한 전자기술의 발전과 자동차에 대한 적용 기술이 향상됨에 따라 앞으로 가변흡기 시스템, 가변밸브 타이밍, 가변 터보, 가변 기통수, 가변 압축비등 가변기술에 대한 연구개발이 더욱 활발히 이루어질 것이다.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.353-360
• /
• 2003

Hydraulic performance and cavitation characteristics of fuel pump in turbo-pump were studied experimentally. The fuel pump has a centrifugal impeller with a separate inducer. In this paper, flow characteristics of inducer and impeller was experimentally investigated separately and together. Especially static pressure distribution of Inducer was examined in non-cavitation and cavitation conditions.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.309-314
• /
• 2003

High-efficiency turboblowers in the next generation have been successfully developed and commercialized first in the world, using the high-speed BLDC motors and the foil air bearings. About 20-35% savings in electricity consumption in the field are found in comparison with the conventional roots rotary blowers and the integral gear-driven turboblowers. Current TB75 and TB150 products are replacing the existing blowers in the worldwide market.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.531-534
• /
• 2006

This study is concerned with radial turbine design and performance improvement of a turbo generator system, which is used for maximizing performance of a 250kW MCFC fuel cell system. A preliminary design of a radial turbine has been performed under the thermodynamic and fluid-dynamic conditions determined by a cycle analysis of the MCFC BOP system. Basic demensions are determined by a meanline analysis and calculation of radial variation at the exit of the turbine. The turbine impeller is designed and modified by iterative processes of three dimensional flow analysis.