• The KSFM Journal of Fluid Machinery
• /
• v.4 no.2 s.11
• /
• pp.22-28
• /
• 2001

This study was performed to evaluate the dynamic behavior of turbo pump unit. The acceptable separate margin of $1^{st}$ critical speed was obtained by the use of elastic-ring inserted ball bearing, while the poor separate margin of $1^{\st}$ critical speed was appeared in the case without the elastic-ring. In addition, the results show that the stiffness and damping of plain seals give more separate margin of $2^{nd}$ critical speed. However the wear or the failure of seals could reduce the $2^{nd}$ critical speed near the operating speed.

• The KSFM Journal of Fluid Machinery
• /
• v.15 no.1
• /
• pp.36-40
• /
• 2012

The magnitude of the axial thrust acting on pump bearings has a great influence on the operational reliability and service life of a pump for turbopumps. In the present study, radial vanes are introduced to the pump casing to control the axial thrust by changing the cavity pressure between the impeller and the casing. To investigate the effect of the vanes on the axial thrust of the pump, experimental and computational studies were performed with and without the vanes. It is shown that the vanes reduce the cavity pressure by preventing the flow from rotating with the impeller. Experimental and computational results show similar trend for the axial thrust difference between two cases with and without the vanes. The results show that the cavity vanes are very effective in controlling the magnitude of the axial thrust.

• The KSFM Journal of Fluid Machinery
• /
• v.13 no.5
• /
• pp.58-63
• /
• 2010

Optimal operation of turbo blowers connected in serial is analyzed by experimental measurements and numerical simulation with three-dimensional Navier-Stokes equations. The turbo blower system considered in the present study is widely used for the refuse collection system. Design optimization of the turbo blower using some design variables is also studied to enhance the performance of the blower. Throughout numerical simulation, it is found that the input energy reduction by optimal operation of the turbo blowers with the proper changes of the rotor's rotating frequency can be reduced a input energy for operating the blower system compared to the conventional on-off operation method theoretically. It is also found that the optimal design method is effective to enhance the performance of the turbo blower.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.4
• /
• pp.47-52
• /
• 2014

An inducer is forward-attached to an impeller to improve the suction performance. This paper described the experimental and numerical investigations on the concept of NPSH similarity about the inducer scale. As Reynolds number decreased for the same scale inducer, the hydraulic performance is slightly reduced because of the viscosity. The suction performance similarity is in good agreement. For different scale inducers, the NPSH similarity did not follow the conventional rule which is proportional to the square of the inducer diameter. A cavity of two times scale inducer grows faster under cavitation inception, and the head is more drop as the fluid passes blades. Because of the simplified cavitation model and vapor pressure, the NPSH similarity dose not have an accuracy. This study suggested an empirical formula for the NPSH similarity.

• Tribology and Lubricants
• /
• v.25 no.3
• /
• pp.187-191
• /
• 2009

A leakage performance test and an endurance performance test of a 75 ton class turbopump mechanical face seal are performed using water under high speed and high temperature environment. A prototype mechanical face seal is manufactured for the purpose of sealing of fuel between a fuel pump and turbine. By simulating operating condition experimentally, the leakage rate and seal carbon wear rate are obtained to evaluate the performance of the prototype mechanical face seal. The test results show the acceptable leakage performance and reasonable wear tendency as well.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.1
• /
• pp.55-65
• /
• 2002

In this study, the procedures for the preliminary design of the turbo-shaft engine for the light multi-purpose helicopter are established. The engine specifications are determined through the performance analysis on the on-design and off-design conditions by the use of simulation program. In addition, the effect of humidity on the engine performance is examined by considering the change of the gas properties and characteristic maps due to moisture contents. The calculation results show that the engine power is reduced by the existence of moisture in working fluid.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.590-595
• /
• 2004

Turbo fan as an air moving device is widely used for its silent characteristics and high efficiency relative to the other centrifugal multi blade impeller. In general, turbo fan is installed with a scroll casing for energy conversion from kinetic one to pressure energy. However, a turbo fan without scroll casing is considered as a present model that is proposed model for compact design of a product In detail, the model has only 4 cutoffs as guiders for 4 separated outlets. Specially, equal distribution of flow rate generated by the model blower is main interest in this investigation. The optimal position of the guider is found by reducing abnormal flows such as reverse flow in each outlet.

• The KSFM Journal of Fluid Machinery
• /
• v.7 no.6 s.27
• /
• pp.38-44
• /
• 2004

In this study, the overall performance and the effect of the tip leakage flow of the centrifugal compressor with a refrigerant HFC-l34a were numerically studied using CFX-TASCflow. To study the effect of the tip leakage flow, the numerical study of the overall performance of HFC-l34a centrifugal compressor with a cascade diffuser was preceded and compared with the experimental result. Six different tip clearances were used to consider the influence of the tip clearance on the performance. The tip leakage flow was illustrated for qualitative discussion. The results obtained in this study can be applied to the determination of the cold clearance.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.109-115
• /
• 2004

The micro turbo generator is new portable power source based on the Brayton cycle, which consists of a compressor, a turbine, a generator, and a combustion chamber. In this paper, the thermodynamic analysis was performed to find the required condition for hundreds watts power in the micro turbo generator, and also the rotordynamic stability was predicted using the numerical analysis of air foil bearings which support the micro turbo generator. By experimental works, the rotordynamic stability of the micro turbo generator with foil bearings was verified. While various transient dynamic situation, the micro turbo generator had stable performances. From the result, it was demonstrated that air foil bearings could be adapted to the micro turbo generator as a excellent lubrication element.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.347-351
• /
• 2004

The cryogenic test facility is developed for test of deep groove ball bearings, floating ring seals, materials (steel & copper) for High Pressure Turbopump of liquid rocket engine (LRE). The cryogenic bearing test is performed to evaluate the flow rate of cooling water and the load-carrying capacity of bearings. The cryogenic seal test is performed to evaluate the determination of magnitude of leakages through the seal, a time variation of this magnitude. The test of the materials Pair is performed to evaluate its fitness for operation in the liquid oxygen medium.