• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.11 no.2
• /
• pp.99-105
• /
• 1991

This study was carried out to provide basic data to be necessary for the selection of an energy recovery process based on the characteristics of municipal solid wastes(MSW). The samples were collected at Kangdong-Ku in Seoul and conducted ultimate and proximate analyses. Laboratory scale anaerobic digesters were operated to determine the non biodegradable fractions of the wastes. The results indicated that carbon and hydrogen contents, and lower heating values could be calculated from the volatile contents of MSW by the following equations : C = 0.57 VS, H =0.084 VS, and HL=49.5 VS-(6-0.045VS) W. Nonbiodegradable fractions were respectively 58.9% of volatile matters and 77.7% of MSW. Incineration and refuse derived fuel(RDF) processes appeared to be the most efficient processes in terms of weight reduction and energy recovery, But determining the energy recovery processes, the fluctuations of heating values of MSW throughout a year and available landfill site and secondary pollution should be considered.

• Polymer(Korea)
• /
• v.33 no.6
• /
• pp.530-536
• /
• 2009

A cycloaliphatic epoxy/acidic anhydride system incorporating short carbon fibers (SCF) and short glass fibers (SGF) was fabricated and thermal/mechanical properties were characterized. At low filler content both SCF- and SGF-reinforced composites showed a similar decrease in coefficient of thermal expansion (CTE), measured by a thermomechanical analyzer, with increasing loadings, above which SCF became more effective than SGF at reducing the CTE. Experimental CTE data for the SCF-reinforced composites is best described by the rule of mixtures at lower SCF contents and by the Craft-Christensen model at higher SCF contents. Storage modulus (E') at $30^{\circ}C$ and $180^{\circ}C$ was greatly enhanced for short fiber-filled composites compared to unfilled specimens, Scanning electron microscopy of the fracture surfaces indicated that the decreased CTE and the increased E' of the short fiber-reinforced composites resulted from good interfacial adhesion between the fibers and epoxy matrix.

• The Korean Journal of Mycology
• /
• v.38 no.2
• /
• pp.136-141
• /
• 2010

To provide a basic information on the chemical concentrations of different raw materials used in mushroom cultivation, the raw materials were collected from 13 Flammulina velutipes, 14 Pleurotus eryngii, and 8 P. ostreatus farms and analyzed to calculate moisture contents, pH, total carbon(T-C), total nitrate(T-N), total phosphate(T-P) and 13 different cations. In our results, the C : N ratios of cotton seed meal, beet pulp, and corn-cob were 6~17, 12~29 and 56~127, respectively. Depending on the companies which process these materials, the range of C:N ratio of soybean curd residue was approximately either 8~9 or 14~17 with wider range of C : N ratio of the raw materials imported from other countries without the detection of heavy metals. In this study, the formula was provided to calculate the composition of mixed media for mushroom cultivation based on the ingredient chart of different raw materials.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.12
• /
• pp.963-969
• /
• 2014

Four coal sources that had different ash contents were evaluated in a drop tube furnace (DTF). Combustion experiments were conducted by using several sources with different particle sizes and excess air ratios under air-staging conditions to determine the optimized combustion conditions of high-ash coal, with an emphasis on the combustion efficiency and NOx emissions. The results show that the higher ash content results in a large amount of carbon remaining unburned, and that this effect is dominant when the largest particle size is used. Furthermore, the ash content of coal does affect the Char-NOx concentration, which decreases with the particle size. The results of this study suggest that an air-staged system can be useful to reduce the NOx emissions of high-ash coal and that control of the air stoichiometric ratio of the primary combustion zone (SR1) is effective for reducing NOx emissions, especially by considering unburned carbon contents.

• Applied Chemistry for Engineering
• /
• v.26 no.2
• /
• pp.224-228
• /
• 2015

The carbon precursor pitch from pyrolyzed fuel oil (PFO), by-product of Naphta cracking process (NCC), was prepared through heat and UV irradiation treatments with various concentrations of $AlCl_3$, which is a new pitch preparation method. The reformed pitches were characterized by measuring their elemental composition, chemical structure of components, molecular weight distribution, and softening point. The oxygen contents of reformed pitch increased as increasing $AlCl_3$ amounts on the other hand, the carbon and hydrogen contents were not nearly changed. UV irradiated reformed pitches were composed of more aromatic carbon compounds than that of using only heat-treatment without any UV irradiation. The addition of $AlCl_3$ catalyst was ineffective on the aromaticity of reformed pitches. The softening point of prepared pitches was in the range of $103.3{\sim}168.9^{\circ}C$. Also the yield of prepared pitch increased from 48% to 80% when 5 wt% of $AlCl_3$ was added during the heat and UV irradiation reforming. It is expected that the UV irradiation reforming method can be practical and helpful to produce high yields of pitches with diverse properties.

• Journal of Conservation Science
• /
• v.28 no.3
• /
• pp.257-264
• /
• 2012

Ancient mirrors are generally made of bronze, and it is very rare to find cases of iron mirrors excavated domestically. In this study, the unidentified ferrous artifact was treated for conservation, and was identified as a mirror. In this process, the sample was taken and analyzed for microstructure, and the manufacturing technology was studied. Analysis involved optical microscope, micro-hardness tester, and SEM-EDS. As the result of analysis, iron mirror structure exist not almost non-metallic inclusions, and partially network cementite was observed. This appears to have been caused by reduced carbon content due to decarburizing the cast iron in the solid state mirror which was created by cast iron. The ledeburite structure of the casting has difficult to cut or polish because has great hardness by high carbon content. Thus, the cast iron mirror was decarburized at a temperature under $850^{\circ}C$ with CO or $CO_2$ blocked, which reduced the hardness of the iron mirror and made it possible to polish the mirror surface. This deformation of structure according to carbon content results from such manufacturing technology.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.9
• /
• pp.939-946
• /
• 2011

In thermal power generation companies, the recycling of refined ash (LOI < 6%) obtained from a PC-firing furnace is beneficial for the companies, e.g., it can be used for making lightweight aggregates. However, ash having a high LOI, which cannot be reused, is still buried in the ground. To obtain refined ash, the re-burning of high-LOI ash (LOI > 6%) in a PC-firing furnace can be an alternative. In this study, a numerical analysis was performed to demonstrate the effects of ash re-burning. An experimental constant value was decided by TGA (thermo-gravimetric analysis), and a DTF (drop-tube furnace) was used in the experiment for calculating the combustion of ash. On the basis of the trajectory of the moving particles of coal and ash, it was concluded that supplying ash near the burner, which is located high above the ground, is appropriate. On the basis of numerical results, it was concluded that an ash supply rate of 6 ton/h is suitable for combustion, without affecting the PC-firing boiler.

• Korean Chemical Engineering Research
• /
• v.45 no.5
• /
• pp.506-514
• /
• 2007

To select the best oxygen carrier particle for syngas fueled chemical-looping combustor, the reduction reactivity and carbon deposition characteristics were determined in a thermogravimetric analyzer. Four kinds of oxygen carrier particles (NiO/bentonite, $NiO/LaAl_{11}O_{18}$, $Co_xO_y/CoAl_2O_4$, $NiO/NiAl_2O_4$) were tested with the simulated syngas (30% $H_2$, 10% $CO_2$, 60% CO) as a reduction gas. With each of these particles, the maximum conversion and oxygen transfer capacity increase with increasing the reduction temperature At the given experimental range, the optimum operating temperature to maximize oxygen transfer rate is found to be $900^{\circ}C$ and carbon deposition on the particles could avoid at the temperature above $800^{\circ}C$. Among four kinds of oxygen carrier particles, the NiO-based particles exhibits better reactivity than the CoO-based particle. Moreover, the NiO/bentonite particle produces the best reactivity based on the oxygen transfer rate and the degree of carbon deposition. The measured oxygen transfer rate increases as the metal oxide content in NiO/bentonite particle is increased thereby higher metal oxide contents could provide stable operation of chemical-looping combustor.

• Economic and Environmental Geology
• /
• v.43 no.2
• /
• pp.85-100
• /
• 2010

Devonian Cairn Formation is one of the important hydrocarbon reservoirs in Alberta, Canada. However, the Cairn Formation, outcropped in the study area, is not prospective reservoir with poor porosity and permeability by some late diagenetic processes. In this study, geochemical characteristics of the Cairn Formation were studied to use these preliminary results for advanced geological and geophysical petroleum explorations in the near future. Rock-Eval pyrolysis showed that total organic carbon content is less than 0.3 wt.%, indicating a minor amount of bitumen and/or other hydrocarbons. The carbonates in the Cairn Formation are mainly composed of subhedral and anhedral dolomites. Pore sizes in the carbonate are various, ranging from nanometer to micrometer. Clastic sediments increase in the upper and lower parts of the Cairn Formation, probably due to changing its depositional conditions. The Cairn Formation can also be divided into several intervals based on Ca/Mg ratio in dolomite and degree of amount of calcite. These could be formed by different sedimentary environment, degree of cementation and recrystallization, different saline/fresh water, etc.

• 한국해양학회지
• /
• v.30 no.4
• /
• pp.302-319
• /
• 1995

The geochemical properties, sedimentation rates, foraminiferal distributions, and oxygen and carbon isotope records of sediment from Cores S-2 and S-19 were studied to investigate late Holocene paleoceanographic and paleoclimatic changes of the admiralty and Maxwell Bay, King George Island, Antarctica. Total organic carbon contents increased from the lower part to the upper part of Cores S-2 and S-19, whereas calcium carbonate contents decreased from the lower part to the upper part of Cores S-2 and s-19,whereas calcium carbonate contents decreased from the lower part to the upper part of Cores S-2 and S-19. Twenty-seven foraminiferal species were identified, and Globocassidurina biora was mostly a bundant in sediment samples. The sedimentation rates ranged from 24 cm/kyr to 237 cm/kyr based on /SUP 14/C-age dating of G. biora. The sedimentation rates increased rapidly in the upper part of the Cores. б/SUP 18/O values ranged from 0.3% to 6.2% and б/SUP 13/C values ranged from -3.0% to 0.0% with several fluctuations of the values. The lowest part of Core S-2, at 128 cmbsf in depth, had a /SUP 14/C-age of 3,100${\pm}$60 yr B.P. and the lowest part of Core S-19, at 230 cmbsf in depth, of 7,400${\pm}$ yr B.P. The results of geochemical and sedimentological analyses of the core sediments suggested five stages of paleoceanographic and paleoclimatic changes as follows: war,-cold stage of 7,500∼6,500 yr B.P., cold stage of 6,500∼3,600 yr B.P., cold-warm stage of 3,600∼2,770 yr B.P., warm stage of 2,770∼2,380 yr B.P. and cold-warm stage of 2,380∼2,100 yr B.P.