• Journal of the Korean earth science society
• /
• v.24 no.5
• /
• pp.477-490
• /
• 2003

Bottom sediments from Youngil Bay, East Coast of Korea, were analyzed for grain composition as well as elemental compositions and total organic carbon (TOC) content in order to investigate the spatial variability and content of metal elements. Grain size distribution of the sediments seems to be controlled by anticlockwise current pattern with bottom topography of the study area. Spatial variability of TOC and all elemental contents reflects those of grain size, but an exception was found in the harbor area (Old-Port): their contents are high in the central part of the bay with the muddy sediment and decrease toward the sand-dominated coastal zone. However, contents of Ca, Sr, K are high in the sand-dominated coastal zone and contents of some heavy metals (Cd, Cu, Zn) are high in the Old-Port area and the mouth of Hyeongsan River. The correlation matrix and R-mode factor analyses reveal that four important factors controlling the distribution of metals in the bay are sediment grain size (or quartz dilution effect), the formation of sulfide minerals associated with decomposition of organic matters under anoxic geochemical environment, calcium carbonate (mainly shell fragments) and coarse-grained feldspar mineral. According to the metal content of labile fraction an CER (concentration enrichment ratio) value, high accumulation of some heavy metals in the harbor area seems to result not formed by early diagenetic processes under anoxic environment.

• Composites Research
• /
• v.29 no.2
• /
• pp.79-84
• /
• 2016

An adhesive can be used to connect two different materials in structures. In comparing with other connecting methods, such as bolt, rivet, and hot melting, the adhesive does not need to use them. It leads to reduce the weight and decrease the stress concentration along the connecting line. This work studied the comparison of mechanical and interfacial properties of commonly-used two adhesives, acrylic type and bisphenol-A epoxy type. Tensile and flexural strength of neat adhesives were also compared. Lap shear test of two adhesives was deduced from the measurement of tensile and fatigue tests. After testing, the failure patterns of adhesive surfaces were observed by a microscope. Tensile strength and mechanical fatigue resistance at using bisphenol-A epoxy adhesive were better than acrylic adhesive. Also adding CNT reinforcement in epoxy adhesive can anticipate mechanical improvement.

• Composites Research
• /
• v.27 no.6
• /
• pp.219-224
• /
• 2014

Nancomposites manufacture has been developed rapidly, because of reinforcing effects of CNT in terms of mechanical, electrical and thermal properties. In this study, 10 wt% CNT paste was fabricated with good dispersion state and easy processability. Damage sensing and reinforcing effect of CNT paste were investigated in nanocomposites. 10 wt% CNT paste exhibited better tensile and flexural properties than those of general 1 wt% CNT nanocomposites. To observe the healing effect of CNT paste, a crack was made artificially with 30wt% CF30wt%/PP composites, and the CNT paste was filled inside the crack. The damage sensing of CNT paste in CF30wt%/PP composites was investigated by electrical resistance measurement and mechanical tests. CNT paste exhibited good reinforcing effect in mechanical properties of CF30wt%/PP composites, and this reinforcing effect was getting better with larger cracks. The reason was because CNT paste had good interfacial adhesion with CF30wt%/PP composites to resist crack propagation. In electrical resistance measurement, there was a jump in electrical resistance signal at the adhesion interface. The jumping signal could be used to predict fracture of CF/PP composites. CNT nanocomposites for damage sensing had crack reducing effect and damage detection using electrical resistance method.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.113-113
• /
• 2017

최근 많은 산업의 발전으로 인해 환경오염을 유발시키는 폐수가 다량으로 배출되고 있으며, 이러한 폐수 속에는 유기용매, 고분자 물질 및 각종 염 등의 난분해성 물질들이 다량으로 함유되어 있다. 이런 물질들을 분해시키기 위해 물리적, 생물학적 수처리 방법이 많이 이용되고 있지만 이 방법들은 각각 운전비용과 처리비용이 고가인 단점이 있다. 따라서 비용과 효율 측면에서 효과적인 폐수처리를 위해서 전기화학적 폐수처리 방법이 많이 사용되고 있다. 물리적, 생물학적 처리 방법에 비해 비용이 적게 들고, 처리 후 잔류물이 남지 않으며, 독성을 띄는 산화제의 첨가 없이도 높은 폐수처리 능력을 보이기 때문에 친환경적이므로, 전기화학적 폐수산화 처리에 사용되는 불용성 전극에 대한 연구가 많이 진행되어져 오고 있다. 그 중 BDD(Boron-doped diamond) 전극은 표면에서 강력한 산화제인 수산화 라디칼의 높은 발생량으로 인해 뛰어난 폐수처리 능력을 보이므로 불용성 전극 분야에서 활발한 연구가 진행 중이다. 그러나 기존에 BDD 전극의 기판 모재로 이용되던 Si, W, Pb등은 모두 기계적 강도, 폐수처리 능력 및 독성 문제로 인해 한계가 있었고, 특히 Nb기판 위에 형성시킨 BDD 전극은 뛰어난 폐수처리 능력에도 불구하고 비싼 모재 원가로 인해 상용화가 힘든 실정이다. 이런 문제점을 해결하기 위해 높은 기계적 강도와 전기화학적 안정성을 가진 Ti 기판을 사용한 BDD 전극에 대한 연구가 보고되고 있다. 그러나 BDD와 Ti 간의 lattice mismatch, BDD층 형성을 위한 고온 공정시 탄소의 확산으로 인한 기판 표면에서의 TiC층 형성으로 인해 접착력이 감소하여 박리가 생기는 문제점이 있다. BDD와 Ti의 접착력을 향상시키기 위해 융점이 높고, 전기전도성이 우수한 TiN을 diffusion barrier layer로 삽입하면 탄소 확산에 의한 TiC층의 생성을 억제하여, 내부응력에 기인한 접착력 감소를 방지할 수 있다. 또 하나의 방법으로 Ti 기판의 전처리를 통해 BDD층의 접착력을 향상 시킬 수 있다. Sanding과 etching을 통해 기판 표면의 물리, 화학적인 표면조도를 부여하고, seeding을 통해 diamond 결정 성장에 도움을 주는 seed 입자를 분포시킴으로써, 중간층과 BDD층의 접착력을 향상시키고, BDD 결정핵 성장을 촉진시켜 고품질의 BDD박막 증착이 가능하다. 본 연구에서는 기존 Si, Nb 등의 기판 모재를 Ti로 대체함으로써 제조원가를 절감시키고, TiN 중간층을 삽입하여 접착력을 향상 시킴으로써 기존의 BDD 전극과 동등한 수준의 물성 및 수처리 특성을 가진 BDD전극 제작을 목표로 하였다. $25{\times}25mm$의 Ti 기판위에 TiN 중간층을 DC magnetron sputtering을 이용하여 증착 후, BDD 전극 층을 HFCVD로 증착하였다. 전처리를 진행한 기판과 중간층 및 BDD층의 미세구조를 XRD로 분석하였고, 표면 형상을 SEM으로 확인하였다. BDD전극의 접착력 분석을 통해 TiN 중간층의 최적 조성을 도출하고, 최종적으로 BDD/TiN/Ti 전극의 CV특성과 가폐수의 COD분해능력 및 축산폐수, 선박평형수 등의 실제 폐수 처리 능력을 BDD/Si, BDD/Nb 전극과 비교 검토할 것이다.

• Composites Research
• /
• v.25 no.4
• /
• pp.93-97
• /
• 2012

Carbon nano fibers (CNFs) reinforced magnesium alloy (AZ91) matrix composites have been fabricated by liquid pressing process. In order to improve the dispersibility of CNFs and the wettability with magnesium alloy melt, CNFs were mixed with submicron sized SiC particles ($SiC_p$). Also, the mixture of CNFs and $SiC_p$ were coated with Ni by electroless plating. In liquid pressing process, AZ91 melts have been pressed hydrostatically and infiltrated into three reinforcement preforms of only CNFs, the mixture of CNFs and $SiC_p$ (CNF+$SiC_p$), and Ni coated CNFs and $SiC_p$ ((CNF+$SiC_p$)/Ni). Some CNFs agglomerates were observed in only CNFs reinforced composite. In cases of the composites reinforce with CNF+$SiC_p$ and (CNF+$SiC_p$)/Ni, CNFs were dispersed homogeneously in the matrix, which resulted in the improvement of mechanical properties. The compressive strengths of CNF+$SiC_p$ and (CNF+$SiC_p$)/Ni reinforced composites were 38% and 28% higher than that of only CNFs composite.

• Journal of Plant Biotechnology
• /
• v.40 no.3
• /
• pp.147-155
• /
• 2013

In this experiment, we report for the first time mass propagation by in vitro mircrotuberization of Codonopsis lanceolata. We first examined the effect of cytokinins on multiple shoot induction. 2.0 $mg{\cdot}L^{-1}$ of kinetin not only gave the highest rate of shoot induction (19.1%) but also the elongation of shoot (17.1 mm). Secondly, we investigated the effect of sugars on in vitro microtuberization from nodal segments. The diameter of tuberous roots was enlarged in the half-strength MS medium supplemented with 145.9 mM sucrose. Histological analysis revealed that the number of parenchymatous cell containing starch grains increased in the tuberous roots. In addition, unlike in non-tuberous root, vascular bundles were scattered inner cortex layer. Thirdly, in order to preserve and stimulate the germination, microtubers were stored at $4^{\circ}C$ refrigerator during 9 months and then transplanted to the artificial soils (vermiculrite : peatmoss = 1:1 v/v), resulting that the rates of survival and germination were 75% and 70%, respectively. These results indicated that mass propagation of C. lanceolata was achieved by in vitro microtuber formation, suggesting that this protocol might be applied for not only the propagation of elite clones but also conservation of C. lanceolata germplasm.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.35-39
• /
• 2011

In this work, mesoporous carbons (CMK-3) were prepared by a conventional templating method using mesoporous silica (SBA-15) for using catalyst supports in polymer electrolyte membrane fuel cells (PEMFCs). The CMK-3 were chemically activated to obtain high surface area and small pore diameter with different potassium hydroxide (KOH) amounts, i.e., 0, 1, 3, and 4 g as an activating agent. And then Pt-Ru was deposited onto activated CMK-3 (K-CMK-3) by a chemical reduction method. The characteristics of Pt-Ru catalysts deposited onto K-CMK-3 were determined by surface area and pore size analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and inductive coupled plasma-mass spectrometry (ICP-MS). The electrochemical properties of Pt-Ru/K-CMK-3 catalysts were also analyzed by cyclic voltammetry (CV). From the results, the K3g-CMK-3 carbon supports activated with 3 g KOH showed the highest specific surface areas. In addition, the K3g-CMK-3 led to uniform dispersion of Pt-Ru onto K-CMK-3, resulted in the enhancement of elelctro-catalystic activity of Pt-Ru catalysts.

• Clean Technology
• /
• v.26 no.2
• /
• pp.131-136
• /
• 2020

Biomass bamboo charcoal is utilized as anode for lithium-ion battery in an effort to find an alternative to conventional resources such as cokes and petroleum pitches. The amorphous phase of the bamboo charcoal is partially converted to graphite through a low temperature graphitization process with iron oxide nanoparticle catalyst impregnated into the bamboo charcoal. An optimum catalysis amount for the graphitization is determined based on the characterization results of TEM, Raman spectroscopy, and XRD. It is found that the graphitization occurs surrounding the surface of the catalysis, and large pores are formed after the removal of the catalysis. The formation of the large pores increases the pore volume and, as a result, reduces the surface area of the graphitized bamboo charcoal. The partial graphitization of the pristine bamboo charcoal improves the discharge capacity and coulombic efficiency compared to the pristine counterpart. However, the discharge capacity of the graphitized charcoal at elevated current density is decreased due to the reduced surface area. These results indicate that the size of the catalysis formed in in-situ graphitization is a critical parameter to determine the battery performance and thus should be tuned as small as one of the pristine charcoal to retain the surface area and eventually improve the discharge capacity at high current density.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.2
• /
• pp.155-164
• /
• 2010

Emission from biomass combustion such as meat charbroiling is an important source of organic aerosol. Since source profiles are necessary input profiles for source apportionment of aerosol by a chemical mass balance model, meat cooking organic source profiles are developed by measuring organic marker compounds, including palmitic acid, stearic acid, oleic acid and cholesterol as well as PAH compounds. Emissions from meat and pork charbroiling are collected on quartz filters with a PM10-high volume sampler, extracted with organic solvents, derivatized with diazomethane/TMS and analyzed by GC/MS isotope dilution method. Organic and elemental carbon are also analyzed by an OCEC analyzer. Wt.% of cholesterol to the organic carbon(OC) content from beef and pork charbroiling is only 0.056 and 0.062, but wt. % of all saturated fatty acids to the OC content from beef and pork charbroiling is 2.727 and 2.022, and the wt% of all unsaturated fatty acids to the OC content is 0.278 and 0.438, respectively. Content of total PAH compounds to the OC content from beef charbroiling is higher than that from pork charbroiling, and those are 0.116 wt% and 0.044 wt%. Among PAH compounds benzo(a)pyrene as a single compound is account for 0.0071 wt% and 0.0023 wt% of OC content from beef and pork charbroiling. Ratios of marker compound to cholesterol are calculated, and those values are in good agreement with the values already reported at the food cooking emission, indicating that they can be used as organic source profiles for the apportionment of organic aerosol.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.157-157
• /
• 2016

최근 많은 산업의 발전으로 인해 환경오염을 유발시키는 폐수가 다량으로 배출되고 있으며, 이러한 폐수 속에는 유기용매, 고분자 물질 및 각종 염 등의 난분해성 물질들이 다량으로 함유되어 있다. 이런 물질들을 분해시키기 위해 물리적, 생물학적 수처리 방법이 많이 이용되고 있지만 이 방법들은 각각 운전비용과 처리비용이 고가인 단점이 있다. 따라서 비용과 효율 측면에서 효과적인 폐수처리를 위해서 전기화학적 폐수처리 방법이 많이 사용되고 있다. 물리적, 생물학적 처리 방법에 비해 비용이 적게 들고, 처리 후 잔류물이 남지 않으며. 독성을 띄는 산화제의 첨가 없이도 높은 폐수처리 능력을 보이기 때문에 친환경적이므로, 전기화학적 폐수산화 처리에 사용되는 불용성 전극에 대한 연구가 많이 진행되어져 오고 있다. 그 중 BDD(Boron-doped diamond) 전극은 표면에서 강력한 산화제인 수산화 라디칼의 높은 발생량으로 인해 뛰어난 폐수처리 능력을 보이므로 불용성 전극 분야에서 활발한 연구가 진행 중이다. 그러나 기존에 BDD 전극의 기판 모재로 이용되던 Si, W, Pb등은 모두 기계적 강도. 폐수처리 능력 및 독성 문제로 인해 한계가 있었고, 특히 Nb기판 위에 형성시킨 BDD 전극은 뛰어난 폐수처리 능력에도 불구하고 비싼 모재 원가로 인해 상용화가 힘든 실정이다. 이런 문제점을 해결하기 위해 높은 기계적 강도와 전기화학적 안정성을 가진 Ti 기판을 사용한 BDD 전극에 대한 연구가 보고되고 있다. 그러나 BDD와 Ti 간의 lattice mismatch, BDD층 형성을 위한 고온 공정 시 탄소의 확산으로 인한 기판 표면에서의 TiC층 형성으로 인해 접착력이 감소하여 박리가 생기는 문제점이 있다. BDD와 Ti의 접착력을 향상시키기 위해 융점이 높고, 전기전도성이 우수한 TiN을 diffusion barrier layer로 삽입하면 탄소 확산에 의한 TiC층의 생성을 억제하여, 내부응력에 기인한 접착력 감소를 방지할 수 있다. 또 하나의 방법으로 Ti 기판의 전처리를 통해 BDD층의 접착력을 향상 시킬 수 있다. Sanding과 etching을 통해 기판 표면의 물리, 화학적인 표면조도를 부여하고, seeding을 통해 diamond 결정 성장에 도움을 주는 seed 입자를 분포시킴으로써, 중간층과 BDD층의 접착력을 향상시키고, BDD 결정핵 성장을 촉진시켜 고품질의 BDD박막 증착이 가능하다. 본 연구에서는 기존 Si, Nb 등의 기판 모재를 Ti로 대체함으로써 제조원가를 절감시키고, TiN 중간층을 삽입하여 접착력을 향상시킴으로써 기존의 BDD 전극과 동등한 수준의 물성 및 수처리 특성을 가진 BDD전극 제작을 목표로 하였다. $25{\times}25mm$의 Ti 기판위에 TiN 중간층을 DC magnetron sputtering을 이용하여 증착 후, BDD 전극 층을 HFCVD로 증착하였다. 전처리를 진행한 기판과 중간층 및 BDD층의 미세구조를 XRD로 분석하였고, 표면 형상을 SEM으로 확인하였다. BDD전극의 접착력 분석을 통해 TiN 중간층의 최적 조성을 도출하고, 최종적으로 BDD/TiN/Ti 전극의 CV특성과 가폐수의 COD분해능력 및 축산폐수, 선박평형수 등의 실제 폐수 처리 능력을 BDD/Si, BDD/Nb 전극과 비교 검토할 것이다.