• Applied Chemistry for Engineering
• /
• v.4 no.2
• /
• pp.365-372
• /
• 1993

$CO_2$ methanation was performed over Ni supported on cation-exchanged Y zeolites under atmospheric pressure at $250{\sim}550^{\circ}C$ and $H_2/CO_2$ mole ratio of 4. Adsorption strength between carbon dioxide and nickel was found to be Influenced by the cation exchanged in the zeolite. TPD(Temperature-programmed desorption) results show that the adsorption strength decreases in the order of Ni/NaY>Ni/MaY>Ni/HY. TPSR(Temperature-programmed surface reaction) results indicate that enhanced methanation activity is obtained when the adsorption strength between carbon dioxide and nickel is stroing. As the reduction temperature increases, the methantion activity of the catalyst increase. From this result the larger size nickel particle seems advantageous for $CO_2$ methanation reaction. The maximum activity is obtained when nickel loading is 3.3wt%. Carbon monoxide is produced as a by-product throughout the reaction temperature range, and as the contact time increases, the selectivity to methane increases and the selectivity to carbon monoxide decreases steadily. Thus methane seems to be produced from $CO_2$ via CO as an intermediate species. In the temperature range of $410{\sim}450^{\circ}C$, the methane production rate is found to be dependent on the orders of 3.3~-0.5 and 1.4~3.6 with respect to $CO_2$ and $H_2$ partial pressures, respectively. This clearly shows that $CO_2$ and $H_2$ are competing for adsorption sites and as the reaction temperature increases, it becomes increasingly difficult for $H_2$ to be adsorbed on the catalyst surface.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.1
• /
• pp.98-103
• /
• 2017

In this study, contributes to improving the state of this problem using cavitation by ultrasonic energy to reduce fuel costs, which take up a considerable part of ship operation costs, by making the use of on-board blended fuel oil more stable. An experiment simulating on-board blending methods was completed. Fuel (M.G.O & MF-180) was mixed at a volume ratio of 0.25:0.75 and, 0.75:0.25, and the effect of ultrasonic energy on blended fuel oil was examined after applying ultrasonic energy to blended fuel oil using an ultrasonic treatment unit. With the results, we confirmed the blending problem reported by vessels and residual carbon was reduced by up to 28.4%. In addition, based on the results for reduction of residual carbon content and dispersion stability, it was confirmed that the collapse pressure of the cavity due to the ultrasonic energy was effective to atomization of fuel particle and the temporary availability of mixed fuel containing a heavy fuel increased.

• Journal of the Korean Magnetics Society
• /
• v.27 no.3
• /
• pp.87-91
• /
• 2017

Carbon-encapsulated Ni and metal Ni nanoparticles were synthesized by levitational gas condensation (LGC). Methane ($CH_4$) gas was used to coat the surface of the Ni nanoparticles. The Ni particles had a core diameter of 10 nm, and were covered by 2~3 nm thin carbon layers with multi-shells structure.The low magnetization comparing with the Ni nanoparticles without carbon-shell results in the coexistence of nonmagnetic carbon and a large surface spin percentage with disordered magnetization orientation for the nanoparticles. Biginelli reactions in the presence of L-proline and Ni and carbon encapsulated Ni nanoparticles were carried out to change the ratio between stereoisomers. The obtained S-enantiomers for 3,4-dihydropyrimidine (DHPM) using catalysts of Ni, and Ni@C was an excess of about ${\Delta}{\sim}7.4%$ and ${\Delta}{\sim}19.6%$, respectively. The nanopowders were fully recovered using magnet to reuse as a catalyst. The Ni@C was shown at same yield to formation of 3,4-DHPM, though it was recycled for catalyst in the reaction.

• Korean Chemical Engineering Research
• /
• v.56 no.2
• /
• pp.281-290
• /
• 2018

As the internal combustion engine vehicles of high fuel efficiency and low emission are demanded, it becomes important to procure technologies for improving low-temperature performance of automotive catalyst systems. In this study, we showed that the combustion rate of diesel particulate matter is greatly enhanced at low temperature by applying fuel-borne catalyst and perovskite catalyst concurrently. It was tried to examine the correlation between elemental composition of perovskite catalyst and combustion activity of mixed catalyst system. To achieve this goal, we applied temperature-programmed oxidation technique in testing the combustion behavior of perovskite-mixed particulate matter bed which contained the element of fuel-borne catalyst or not. We tried to explain the synergetic action of two catalyst components by comparing the trends of concentrations of carbon dioxide and nitrogen oxide in temperature-programmed oxidation results.

• Analytical Science and Technology
• /
• v.10 no.1
• /
• pp.66-74
• /
• 1997

Influence of the axial dispersion on immobilized enzyme catalytic bed was investigated in order to examine the kinetic behavior of the biocatalysis. The enzyme employed in this study was the tyrosinase(EC 1.14.18.1) immobilized on carbon support : this system requires two substrates of phenol and oxygen. This enzyme has potential application for phenol degradation in waste water. A simulated reactor was a packed-bed reactor of 2.54cm in diameter and 10cm long, loaded with the immobilized carbon particle with an average diameter of $550{\mu}m$. A phenol feed in the strength of 55.5mM(5220ppm) was used to observe the behavior of the immobilized enzyme column at three different dissolved oxygen levels of 0.08445mM(2.7ppm), 0.1689mM(5.4ppm) and 0.3378mM(9.5ppm) with the flow rates in the range of 60(1mL/s) to 180mL/min(3mL/s). Examination of the Biot number and Damkolher numbers of the immobilized system enables us to eliminate the contribution of external mass transfer to set of differential equations derived from the dispersion model. Solution of the equation was finally obtained numerically with the application of the Danckwert boundary conditions and the assumed zero-and first order rates on the non-linear two substrate enzyme kinetics. Higher conversion of phenol was observed at the low flow rates and at the higher oxygen concentration. Comparison of axial dispersion and plug flow model showed that no detectable difference was observed in the column outlet conversion between the axial and the plug flow models which was in complete agreement with the previous studies.

• Membrane Journal
• /
• v.32 no.5
• /
• pp.314-324
• /
• 2022

This study is aimed to design a membrane process that systematically removes contaminants including microplastics in sun-dried salt using a separation membrane. In this study, we selected the separation membrane material, pore size, and module suitable for the sun-dried salt fields, and proceeded with the experiments under the salt fields and laboratory conditions. A pilot plant was constructed and tested in our lab and in the actual saltern with the selected 200 kDa, 4 kDa ultrafiltration membranes, and 3 kDa nanofiltration membranes. Most of the impurities in the sea salt were 0.1 ㎛ in size, and more than 7 types of various microplastics were detected in the impurities. After that, as a result of checking the filtered water through the separation membrane process, no impurities were detected. As a result of comparing the existing sea salt component and the sea salt component prepared with separation membrane filtrate, impurities were effectively removed without change in the sea salt component.

• Korean Chemical Engineering Research
• /
• v.62 no.1
• /
• pp.99-104
• /
• 2024

In this study, a carbon coated hollow silicon (HSi/C) composite material was prepared for anode material of high-capacity lithiun-ion battery. Hollow silica (HSiO₂) was synthesized by the Stöber method with CTAB (N-Cetyltrimethylammonium bromide). The HSi/C anode composite was manufactured by carbon coating after magnesiothermic reduction of HSiO₂. The physical and electrochemical characteristics of the prepared anode materials were investigated based on CTAB amount. In the FE-SEM analysis, it was found that the HSiO₂ particle size increased as CTAB amount decreased, but shell thickness decreased. The HSi/C composites exhibited high initial discharge capacities of 1866.7, 2164.5 and 2188.6 mAh/g with various CTAB ratios (0.5, 1.0, 1.5), respectively. After 100 cycles of charge-discharge, 0.5-HSi/C demonstrated a high reversible capacity of 1171.3 mAh/g and a capacity retention of 70.9%. Electrochemical impedance spectroscopy (EIS) was employed to analyze the impedance characteristics, and it revealed that 0.5-HSi/C showed more stable resistance characteristics than HSi/C composites with other CTAB amount over 20 cycles.

• Microbiology and Biotechnology Letters
• /
• v.17 no.6
• /
• pp.611-618
• /
• 1989

Effects of methionine on cephalosporin C(CPC) production in a fluidized-bed bioreactor were investigated using bioparticles of Cephalosporium acremonium. Since methionine was found to be an important metabolic regulator on the synthesis of cephalosporin C, the effects of its concentration in the cuture broth and feeding mode to the bioreactor were studied. It was observed that the presence of initial methionine was essential for higher cephalosporin C production and there existed an optimal content of methionine. Carbon consumption rate also increased significantly under the presence of methionine. Production of cephalosporin C was most active when methionine was exhausted in the broth; however its additional feeding did not enhance the antibiotic production in the fluidized-bed bioreactor as much as expected. It was therfore considered important to feed an optimal content of methionine at the early operating stage for a higher cephalosporin C production in a fluidized-bed bioreactor. An interesting thing to note was that titre of the antibiotic with reused bioparticles was about 2 times higher in the methionine containing medium than that without methionine. Therefore repeated use of bioparticles, with an optimal content of methionine, was believed to be very useful to enhance to process productivity.

• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.523-530
• /
• 1999

Acrylic pressure-sensitive adhesive has been made utilizing organic solvents, but nowadays it is made by solvent-free system due to environmental problems. In this study, emulsion polymerization were carried out at $40^{\circ}C$ with methacrylic acid(MAA), n-butyl acrylate(n-BA) and 2-ethylhexyl acrylate(2-EHA) as monomers in the presence of anionic(sodium dodecyl sulfate, SDS) and nonionic(ethylene oxide types) surfactant mixtures. The overall conversion of the polymerization reaction in a mixed surfactant system was found to be higher than that in a single surfactant system. Emulsion stability in mixed or anionic surfactant systems was found to be over 12 week, which was better than that in nonionic surfactant system. Emulsion particle size decreased as surfactant content increased. The Tg and molecular weight of emulsion polymer were inependent of the type, the amount and the mixing ratio of surfactant. Based on the results of stability and peel strength, the optimum nonionic surfactant ratio in total 4 g of surfactant mixture systems is found to be 40~60% by weight where the nonionic surfactant has 50 ethylene oxide groups and 16~18 carbon atoms in hydrophobic alkyl chain.

• Resources Recycling
• /
• v.8 no.3
• /
• pp.9-17
• /
• 1999

The study investrgated the properti es of lh$\xi$ dust~ from felToalloy manufacture, The chemical composition, composItron material, particle size and shapes of the bulk dust, sized dust and magnetically separated dust were llivestigated. As the result, we s suppose that the dust from HLgh Carbon Fenomauganesc Manufacturing Process is not sufficient as soource material of Mn because of the low Mn conteut (13.5%) aud complicated composition material The dust from Bag Filter of AOD Process is m mainly made up of $0.2~2\mu\textrm{m}$ $Mn_3O_4$ (Hausmatmite) particle in spherical shape and the Mn content is 63.1%. The dust from Cooler of AOD Process is mainly made up of coarse $Ca(OH)_2$ Mn, $Fe_yO_2$ $SiO_2$ and fine $Mn_3O_1$.