• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.267-268
• /
• 2013

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.147-148
• /
• 2007

• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.1975-1981
• /
• 1991

본 연구에서는 완전히 불균일한 격자계를 사용하여 프로파일링을 한 원통형로 울러의 프로파일링 시작점 부근에서의 압력분포 및 유막형상과 함께 무차원변수의 변 화에 따른 최소유막의 거동을 상세히 조사하고자 한다. 이 결과에서 실제 로울리 베 어링의 로울러 프로파일의 설계시에 적용할 수 있는 새로운 기준을 제시하고자 한다.

• Tribology and Lubricants
• /
• 제31권4호
• /
• pp.177-182
• /
• 2015

Tapered roller bearings are widely used in equipment where high combined thrust and radial loads are experienced. A certain amount of tilting between the tapered rollers and the races always occurs because of bending moment load conditions and shaft deflection. It is now well understood that a coherent elastohydrodynamic lubrication (EHL) film separates the rollers and races. In spite of extensive study on EHL problems for over half a century, relatively few studies have focused on the finite line contacts problem. This study presents a complete numerical analysis of the effects of roller tilting on the EHL characteristics in a tapered roller bearing. We systematically analyze this highly nonlinear problem using finite differences with fully non-uniform grids and the Newton-Raphson method. Detailed EHL pressure distributions and film shapes are presented under moderate loads and material parameters. A very small roller tilting significantly affects the pressure distributions and film shapes near both ends of the roller. Moreover, the effect of tilting on the EHL characteristics at the small end is much greater than that at the large end. Therefore, in designing optimum profiles for tapered roller bearings, the profile radius should be larger at the small end.

• Tribology and Lubricants
• /
• 제23권5호
• /
• pp.187-194
• /
• 2007

The profile of the roller in the axial direction is the main design factor in order to increase endurance life against the contact fatigue due to the stress concentration along the edge of the roller. Even under the elas-tohydrodynamic lubrication (ehl) conditions, the stress concentration along the edge of the roller greatly worsens the fatigue life both for the roller and contacting body. In this study, roller contacts of finite axial length are studied for the film thickness and pressure of ehl. For the real contact behaviors under the ehl conditions, multigrid and multi-level method is applied so that much higher loading conditions can be investigated. Several axial profiles of roller are investigated to verify how both ehl film and pressure are generated and some of them are recommended for the ehl contact condition.

• Tribology and Lubricants
• /
• 제27권6호
• /
• pp.326-331
• /
• 2011

The purpose of this paper is to analyze and discuss the effects of surface roughness by comparing the elastohydrodynamic lubrication(EHL) analysis of smooth surface and rough surface as the ball bearing. In order to do this, The average flow model is adapted for the interaction of the flow rheology of lubricant and surface roughness. The average Reynolds equation and the related flow factor which describes the coupled effects of surface roughness and flow rheology, the viscosity-pressure and density-pressure relations equations, the elastic deformation equation, and the force balance equation are solved simultaneously. The results show that effects of surface roughness on the film thickness and pressre distribution should be considered especially in EHL contact problems.

• 대한기계학회논문집
• /
• 제15권2호
• /
• pp.523-536
• /
• 1991

This dissertation analyzes the running mechanism of flexible and thin tape above rotating head through the numerical simulation and the experiment. The scope of analysis is confined to the phenomena of two dimensional elasto hydrodynamic lubrication between the protruded bump on a rotating cylinder and the running tape. This model is based on the elastic deformation equation of plate and shell and Reynolds equation. Finite difference method is employed as a numerical technique to calculate (1) the distribution of pressure between the running tape and rotating bump and (2) the vertical deformation of elastic thin tape over he rotating bump under hydrodynamic pressure. In numerical analyses, the effects of bump size on flying characteristics of the tape were evaluated and examined considering the influence of tension and stiffness of tape.

• Tribology and Lubricants
• /
• 제33권1호
• /
• pp.23-30
• /
• 2017

The electric controlled marine diesel engine has fuel pump generating the high pressurized fuel for fuel injection to combustion chamber via a common rail. Fuel pump consists of a cam-roller system. Journal bearing installed between a roller and a cam-roller pin is subjected to fluctuating heavy and instant loads by cam lift. First, Kinematic analysis is carried out to predict bearing loads during one cycle acting on the journal bearing. Second, flexible multi-body dynamic analysis and transient elasto-hydrodynamic(EHD) lubrication analysis for journal bearing considering elastic deformation of cam-roller pin, roller and bearing are conducted using AVL EXCITE/PU software to predict lubrication performance. The clearance ratio and journal groove shape providing lubrication oil are important parameter in bearing design having good performance and can be changed easier than other design parameters such as diameter, width, oil supply pressure and bearing material grade. Generally, journal bearing performance is represented by the minimum oil film thickness(MOFT) and peak oil film pressure(POFP). As well as the traditional design parameters(MOFT, POFP), in this study, temperature rise of lubrication oil is also evaluated through the side leakage flow of supplied oil. By the evaluating MOFT, POFP and temperature rise, the optimum bearing clearance ratio is decided.

• 한국전산구조공학회논문집
• /
• 제15권1호
• /
• pp.155-164
• /
• 2002

저널과의 마찰과 마멸을 줄이기 위하여 저널베어링이 사용된다. 저널베어링은 유체 윤활 상대에서 사용되나, 압력이 지나치게 높거나 회전 속도가 작아지면 탄성 유체 윤활 상태의 유막이 파괴되어 접촉부의 돌기가 접촉되는 경계 윤활 상태가 된다. 따라서 혼합 윤활 상태가 되면 저널베어링의 마멸량이 증가하게 된다 본 논문은 마멸율을 최소화함으로 저널베어링의 수명을 연장하는 최적설계를 수행하였다 목적 함수로 혼합 윤활 영역에서 적용되는 마멸을 함수를 사용하였고, 저널베어링 설계에서 고려할 성능 인자들인 마찰 손실, 안정 한계 속도, 유막 파라미터 등을 제약 함수로 사용하였다. 저널베어링 형상을 나타내는 베어링 반경, 축 반경, 베어링 폭 등에서 본 연구는 베어링 반경을 설계 변수로 하였다. 정식화한 설계인자를 이용하여 저널베어링의 최적 설계를 순차 이차 계획법인 PLBA알고리즘을 사용하여 수행하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제29회 춘계학술대회
• /
• pp.182-188
• /
• 1999

A theoretical study of elastohydrodynamic lubrication of elliptical contacts with both rolling and spin has been carried out. A finite difference method and the Newton-Raphson method are applied to solve the problem. The velocity vectors resulting from combined spin and rolling/sliding motion lead to asymmetric pressure distributions and film shapes. Film contours and variations of the minimum and central film thicknesses are compared with various spin-roll ratios. At high spin-roll ratios the minimum film thickness is considerably reduced, whereas the central film thickness decreases less dramatically, The present numerical scheme can be used in the analysis of general elliptical contact problems.