• Journal of IKEEE
• /
• v.28 no.1
• /
• pp.38-45
• /
• 2024

Most previous works about magnetic effect on plasma emission were interested in emission enhancement which was useful to various fields of plasma application. On the contrary, the following work is interested in plasma dissipation rarely reported in prior researches and expected to help advance plasma-controlling technique. Nd:YAG laser (1064 nm, 6 ns) was focused on three kinds of metals (Al, Ti and STS) and air. The permanent magnetic field (0.4 T) of Nd₂Fe₁₄B magnet was provided passing throughout laser-induced plasma. The spectra of plasma in both the presence and absence of the magnetic field were observed with varying laser power and delay time of the spectrograph. In this work it was uniquely discovered that the plasma always dissipated easily in the presence of magnetic field irrespective of the laser power. With the O I(777.42 nm)-line shape function fitted to Lorentz profile, its half width at half maximum (HWHM) was evaluated to verify that the magnetic field increased the plasma density. It is concluded that magnetic field facilitates not only plasma emission enhancement but also plasma dissipation, increasing recombination rate which is proportional to plasma density.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.9
• /
• pp.58-67
• /
• 2009

This paper presents a fully digital gain control system with a new high bandwidth and wide dynamic range power detector for DVB-S2 application. Because the peak-to-average power ratio (PAPR) of DVB-S2 system is so high and the settling time requirement is so stringent, the conventional closed-loop analog gain control scheme cannot be used. The digital gain control is necessary for the robust gain control and the direct digital interface with the baseband modem. Also, it has several advantages over the analog gain control in terms of the settling time and insensitivity to the process, voltage and temperature variation. In order to have a wide gain range with fine step resolution, a new AGC system is proposed. The system is composed of high-bandwidth digital VGAs, wide dynamic range power detectors with RMS detector, low power SAR type ADC, and a digital gain controller. To reduce the power consumption and chip area, only one SAR type ADC is used, and its input is time-interleaved based on four power detectors. Simulation and measurement results show that the new AGC system converges with gain error less than 0.25 dB to the desired level within $10{\mu}s$. It is implemented in a $0.18{\mu}m$ CMOS process. The measurement results of the proposed IF AGC system exhibit 80-dB gain range with 0.25-dB resolution, 8 nV/$\sqrt{Hz}$ input referred noise, and 5-dBm $IIP_3$ at 60-mW power consumption. The power detector shows the 35dB dynamic range for 100 MHz input.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.3
• /
• pp.421-435
• /
• 2017

Recently, due to the saturation of ground structures and the overpopulation of pipeline facilities requires to development of underground structures as an alternative to ground structures. Thus, mechanized tunnel construction of the shield TBM method has been increasing in order to prevent vibration and noise problems in construction of the NATM tunnel for the urban infrastructure construction. Tunnel construction plan for the tunnel line should be formed in a sharp curve to avoid building foundation and underground structures and it is inevitable to develop a shield TBM technology that suits the sharp curve tunnel construction. Therefore, this study is about the structural stability technology of the articulation jack, shield jack and skin plate for the shield TBM thrust in case of the mechanized tunnel construction that is a straight and sharp curve line. The construction case study and shield TBM operation principle are examined and analyzed by the theoretical approach. The torque of the cutter head, the thrust of the articulation jack and the shield jack, the amount of over cutting for curve is important respectively in shield TBM construction of straight and sharp curve line. In addition, it is very important to secure the stability of the skin plate structure to ensure the safety of the inside worker. This study examines the general structure and construction of the equipment, experimental simulation was carried out through numerical analysis to examine the main factors and structural stability of the skin plate structure. The structural stability of the skin plate was evaluated and optimizes the shape by comparing the loads of the articulation jack by selecting the virtual soil to be applied in a straight and sharp curve line construction. Since the present structure and operation method of the shield TBM type in domestic constructions are very similar, this study will help to develop the localized shield TBM technology for the new equipment and the vulnerability and stability review.

• Food Science and Preservation
• /
• v.9 no.3
• /
• pp.315-320
• /
• 2002

In order to improve some problems such as contamination of undesirable mold, mycotoxin production and excessive drying on the surface of traditional meju. Control meju without koji and capsule type meju(CM) coated with soybean mixture containing 0.5%, 1% and 2%(w/w) R. oligosporus koji were dried at room temperature (10∼15$^{\circ}C$) for 3 days. Control meju I was fermented in outdoor for 27 days. Control meju IIand CMs were fermented in Korean yellow clay room at 25$^{\circ}C$ for 7 days under 80% relative humidity as first step, and then fermented in outdoor (average temp. 2.7$^{\circ}C$, December) for 20 days as second step. The moisture content of CMs were higher than that of control meju I to the range of 2.88∼7.55%(w/w). pH and titratable acidity in CMs were similar to control group. Amino type nitrogen content in CMs(800.80, 816.0, 901.60 mg%) were 2.2∼2.6 times higher than that in control meju I (347.2 mg%). Reducing sugar content in CMs(2.78∼3.13%) was similar to control meiu I (2.10%) and control meju H(2.31%). Lightness(L) value of control meju I was higher than that of control meju IIand CMs.

• Korean Journal of Ecology and Environment
• /
• v.43 no.3
• /
• pp.400-408
• /
• 2010

The growth and microcystins production characteristics of three species of Microcystis (M. aeruginosa, M. ichthyoblabe, M. viridis) isolated from Yeongchun dam and Ankei dam in Kyungpook Province, South Korea were investigated at temperatures of $15{\sim}35^{\circ}C$ and light intensities of $35{\sim}180\;{\mu}mol\;m^{-2}\;s^{-1}$. All of the three species exhibited the highest growth rates (${\mu}_{max}$) over the $30^{\circ}C$. The maximum growth rates of M. aeruginosa and M. ichthyoblabe was observed at $70\;{\mu}mol\;m^{-2}\;s^{-1}$, while M. viridis showed maximum growth rate at $35\;{\mu}mol\;m^{-2}\;s^{-1}$. The maximum production of total microcystins was observed at $20^{\circ}C$, and the production of microcystins decreased according as temperature increase. The highest microcystins production of M. aeruginosa, M. ichthyoblabe and M. viridis observed at light intensities of $120\;{\mu}mol\;m^{-2}\;s^{-1}$, $70\;{\mu}mol\;m^{-2}\;s^{-1}$ and $35\;{\mu}mol\;m^{-2}\;s^{-1}$, respectively. The concentration of microcyst in production and microcystin types of three species according to temperatures and light intensities showed clear difference between the species.

• Journal of the HCI Society of Korea
• /
• v.12 no.1
• /
• pp.5-13
• /
• 2017

Interactive intervention of the human presenter is one of the important factors that make the visualization more effective. Rather than just showing the content, the presenter enhances the process of the information delivery by providing the context of visualization. In this paper, we define this as an augmented presentation. In augmented presentation concept, the presenter can facilitate presentation more actively by being fully immersed in the visualization space and reaching and interacting into digital information. In order to concrete the concept, we design presentation space that enables the presenter to be seamlessly immersed in the visualization. Also we increase the presenter's roles as a storyteller, controller and augmenter allowing the presenter to fully support communicative process between the audience and the visualization. Then, we present an augmented presentation system to verify the proposed concept. We rendered 3D visualization through a half-mirror film and a wall projection screen that are place in parallel and applied with stereoscopic images, then, spatially align the presenter inside the virtual visualization space. After that, we conduct a controlled experiment to investigate the subjective level of immersion and engagement of the audience to HoloStation compared to traditional presentation system. Our initial investigation suggests that the newly conceived augmented presentation has potential not only to enhance the information presentation but also to supports the delivery of visualization.

• The Journal of Internal Korean Medicine
• /
• v.33 no.3
• /
• pp.257-271
• /
• 2012

Objectives : The purpose of this study was to confirm that the pulse analyzer is useful for analyzing characteristics of variables of pulse waves in age categories, evaluating pulse waves of the metabolic syndrome group, compared with those of the non-metabolic syndrome group in Korean adults. Methods : The pulse wave variables were measured in Guan of all 1,056 subjects by the pulse analyzer, using a pen-type piezoresistive sensor. The physical measurement, blood test and survey were also performed by each subject. Results : In the age categories, height of pre-incisura (h2), height of tidal wave (h3), area of percussion wave (Aw), and width of percussion wave (w) increased in accordance with increase in age. While ratio of systolic period area (As) went up according to the increase of age, ratio of diastolic period area (Ad) went down. Radial augmentation index (R-AI), h2/h1, h3/h1, w/t and angle of percussion wave went up by aging, generally. Aw rate (Aw/At) also increased. Among the metabolic syndrome group, in the ages of 19 and 44, ratio of systolic period area (As) was higher and ratio of diastolic period area (Ad) was lower than in the non-metabolic group. w/t, Aw/At, and angle of percussion wave were higher than in the non-metabolic syndrome group. Among the metabolic syndrome group over the age of 60, height of pre-incisura (h2), height of tidal wave (h3), total area (At), area of percussion wave (Aw), radial augmentation index (R-AI), h2/h1 and h3/h1 were higher than in the non-metabolic syndrome group. Conclusions : The pulse analyzer is useful to analyze arterial stiffness in the age categories and in the metabolic syndrome group by some measures.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.3
• /
• pp.43-49
• /
• 2010

Direct printing technology is an attractive metallization method, which has become immerging as "Green technology" to the conventional photolithography, on account of low cost, simple process and environment-friendliness. In order to commercialize the printed electronics in industry, it is essential to evaluate the electrical properties of conductive circuits using direct printing technology. In this contribution, we focused on the electrical characteristics of inkjet-printed circuits. A Cu nanoink was inkjet-printed onto a Bisaleimide triazine(BT) substrate with parallel transmission line(PTL) and coplanar waveguide(CPW) type, then was sintered at $250^{\circ}C$ for 30 min. We calculated the resistivity of printed circuits through direct current resistance by the measurement of I-V curve: the resistivity was approximately 0.558 ${\mu}{\Omega}{\cdot}cm$ which is about 3.3 times that of bulk Cu. Cascade's probe system in the frequency range from 0 to 30 GHz were employed to measure the Scattering parameter(S-parameter) with or without a gap between the substrate and the probe station chuck. The result of measured S-parameter showed that all printed circuits had over 5 dB of return loss in the entire frequency range. In the curve of insertion loss, $S_{21}$, showed that the PTL type circuits had better transmission of radio frequency (RF) than CPW type.

• Korean Journal of Microbiology
• /
• v.44 no.3
• /
• pp.203-211
• /
• 2008

Rapid detection-method for Shiga toxin type 1 that was produced from Shiga toxin-producing Escherichia coli (STEC) was developed by two-step ultra-rapid real-time (URRT) PCR. The specific primers were deduced from 80 bp stable region of stx type 1 (stxl) gene among various informations of STEC strains. URRT PCR is a microchip-based real-time PCR using 6 ${\mu}l$ of reaction volume with extremely short denaturation step and annealing/extension step (1 sec, 3 sec, respectively) in each cycle of PCR. Using the stx1-specific URRT PCR, 35 cycled PCR were finished in time of 6 min and 38 see, also measured 7 min and 28 see including melting temperature (Tm) analysis. The detection-limit of stxl-specific URRT-PCR was estimated until 3 colony forming units / PCR with products with stable Tm at $81.42{\pm}0.34^{\circ}C$. In the applications to various STEC strains and contaminated genomic DNAs, stx1-specific URRT-PCR were tested and shown that it would be expected an useful method for the rapid detection of stx1-coded STEC strains.

• Geotechnical Engineering
• /
• v.12 no.6
• /
• pp.51-64
• /
• 1996

After the model open-ended pile attached with strain gages was driven into a pressure chamber, in which the saturated microfine sand was contained, the static compression loading test was performed for that pile. Based on the test results, ultimate pile capacity was determined. Then, either simulated earthquake shaking or sinusoidal shaking was applied to the pile with the sustained certain level OP ultimate pile load. Then, pile capacity degradations characteristics during shaking were studied. Pile capacity degradation during two different shakings were greatly different. During the simulated earthquake shaking, capacity degradation depended upon the magnitude of applied load. When the load applied to the pile top was less than 70% of ultimate pile capacidy, pile capacity degradation rate was less than 8%, and pile with the sustained ultimate pile load had the degradation rate of 90%. Also, most of pile capacity degradation was reduced in outer skin friction and degradation rate was about 80% of ultimate pile capacity reduction. During sinusoidal shaking, pile capacity degradation did not depend on the magnitude of applied load. It depended on the amplitude and the frequency , the larger the amplitude and the fewer the frequency was, the higher the degradation rate was. Reduction pattern of unit soil plugging (once depended on the mode of shaking. Unit soil plugging force by the simulated earthquake shaking was reduced in the bottom 3.0 D, of the toe irrespective of the applied load, while reduction of unit soil plugging force by sinusoidal shaking was occurred in the bottom 1.0-3.0D, of the toe. Also, the soil plugging force was reduced more than that during simulated earthquake shaking and degradation rate of the pile capacity depended on the magnitude of the applied load.