• 대한기계학회논문집A
• /
• 제34권8호
• /
• pp.1129-1136
• /
• 2010

체결클러치에 부착된 댐퍼스프링은 유체커플링에서 직결로 변환될 때 발생하는 엔진 토크의 진동을 흡수하는 역할을 한다. 본 연구에서는 체결클러치의 성능을 좌우하는 압축스프링 및 지지 판 구조물의 최적설계를 통해서 새로운 설계형상을 제안하였다. 체결클러치와 연결된 엔진, 변속기, 구동축 및 휠, 차체질량 등 주요 부품들을 다 포함하는 다물체 동역학모델을 구성하여 공진 회피에 필요한 스프링상수를 계산하였다. 또한 어닐링 모사법에 의한 스프링 최적설계코드를 개발한 후 스프링상수, 최대충격토크, 수축각도, 스프링개수, 피로강도 등을 입력하여 압축 스프링의 사양을 최적화하였다. 이들 스프링을 지지하는 3 가지의 판에 대해서 컴플라이언스를 최소화하고 체적비를 0.3 이하로 하는 위상최적화를 수행하여 새로운 형상을 제안하였다.

• Tribology and Lubricants
• /
• 제33권3호
• /
• pp.85-91
• /
• 2017

This work studies the flow behaviors in the gap between the friction pad and separator in wet-clutch systems. The fluid volume of the lubricant is modeled using the entire system of wet-clutch pack of a dual clutch transmission that has larger outer radius of odd gear shifts and smaller inner radius of even gear shifts. Flow behaviors in the gap of the clutch pad are computed using the gear shift modes that consider the real relative velocities between the friction pad and separator. Flow behaviors in the gap of the disengaged clutch pad are mainly investigated for the wet-clutch system, whereas the engaged clutch pad is modeled with no fluid rate through the contacting surfaces. The developed hydrodynamic fluid pressures and velocity fields in the clutch pad gap are computed to obtain the relevant information for managing flow rates in wet-clutch packs under dual operating conditions during gear shifts. These hydrodynamic pressures and velocity fields are compared on the basis of each gear level and gap location, which is necessary to determine the effects of groove patterns on the friction pad. Shear stresses in the gap locations are also computed on the basis of the gear level for the inner and outer clutch pads. The computed results are compared and used for the design of cooling capacity against frictional heat generation in wet-clutch pack systems.

• Tribology and Lubricants
• /
• 제30권5호
• /
• pp.265-270
• /
• 2014

Frictional heat greatly influences the friction behaviors during clutch engagement. Therefore, the engagement of a wet or dry clutch is frequently not under control by the frictional heat. In a wet clutch, the frictional temperature also specially needs to be controlled, and in many cases, the clutch material is selected to prevent a temperature rise from the friction between friction pad and separator. However, only the selection of the clutch material cannot ensure sufficient control of the temperature rise by the friction. The groove pattern on a friction pad is designed for more flow rates of transmission fluid between the contact gap of clutch pad and separator for the cooling effect. In this work, grove patterns are designed for more flow rates out of the contact gap between friction pad and separator plate. Selected groove design shows the improvement flow rates of transmission fluid through both inner and outer radius, where most of the transmission fluid flows through the outer radius when the clutch is engaged due to the centrifugal force in conventional wet clutch groove. Several comparisons of the amounts of frictional heat generated on clutch pads are made in order to verify the decrease of the temperature rise according to the flow rates along the groove patterns.

• 한국자동차공학회논문집
• /
• 제24권2호
• /
• pp.183-190
• /
• 2016

Engine torque is transferred to the transmission where drag torque is minimized improving fuel efficiency. This is particularly true in a wet clutch pack. This study measures slip friction when the wet clutch pack in a DCT (Dual-Clutch Transmission) is disengaged, and the friction pads are slipping. Shudder engagement velocity, and applied forces can be measured under various working conditions through these torque transfer experiments. Test results demonstrate that the design parameters, and engagement conditions of wet clutch packs can be optimized to reduce shudder and frictional vibration during engagement in a dual clutch transmission.

• 드라이브 ㆍ 컨트롤
• /
• 제21권1호
• /
• pp.1-7
• /
• 2024

The locking performance of a multi-plate clutch with a mechanical lock-up system is governed by the engagement algorithm. In this paper, a control algorithm to improve the locking performance of the clutch was studied. A 1D dynamic model was constructed and simulated according to the developed algorithm. The developed algorithm was composed of a method in which the locking device is engaged while generating artificial slip on the friction plate by controlling the piston pressure of the clutch. Furthermore, a case study of the parameters within the developed algorithm was conducted to explore combinations that maximize locking performance and analyze trends according to these parameters.

• Tribology and Lubricants
• /
• 제30권2호
• /
• pp.92-98
• /
• 2014

Transmission fluid film behaviors in the gap between the wet clutch pad and separator plate are analyzed using the CFD software ADINA. Three pattern groove designs are selected and are used to validate the fluid film behaviors based on the outlet flow in the gap when the wet clutch pad and separator plate are engaged. The main design goal for pattern grooves is faster engagement. In most cases, much of the outlet flow of transmission fluid in the gap occurs on the outer radius boundary due to the centrifugal force generated by the clutch pad circular motion. Groove patterns are created to ensure faster transmission fluid outlet flow in the direction of the inner radius boundary. Computational results of the selected groove patterns are compared.

• Tribology and Lubricants
• /
• 제33권1호
• /
• pp.1-8
• /
• 2017

Drag torque reduction in a wet clutch pack is a key aspect of the design process of the dual clutch transmission (DCT) system. In order to reduce the drag torque caused by lubricant shear resistance, recently developed wet clutch pack systems of DCT, as well as automatic transmission and other four-wheel drive (4WD) couplings, frequently utilize wavy wet clutch pads. Therefore, wavy shape of friction pad are made on the groove patterns like waffle pattern for the reduction of drag torque. Additionally, the groove patterns are designed with larger channels at several locations on the friction pad to facilitate faster outflow of lubricant. However, channel performance is a function of the waviness of the friction pad at the location of the particular channel. This is because the discharge sectional area varies according to the waviness amplitude at the location of the particular channel. The higher location of the additional channel on the friction pad results in a larger cross-sectional area, which allows for a larger flow discharge rate. This results in reduction of the drag torque caused by the shear resistance of DCTF, because of marginal volume fraction of fluid (VOF) in the space between the friction pad and separator. This study computes the VOF in the space between the friction pad and separator, the hydrodynamic pressure developed, and the shear resistance of friction torque, by using CFD software (FLUENT). In addition, the study investigates the dependence of these parameters on the location and waviness amplitude of the channel pattern on the friction pad. The paper presents design guidelines on the proper location of high waviness amplitude on wavy friction pads.

• 한국산학기술학회논문지
• /
• 제21권5호
• /
• pp.77-83
• /
• 2020

오늘날 자동차 산업의 기술 발전으로 4륜구동 기술이 승용차에도 적용되고 있으며, 이를 위해 트랜스퍼 케이스용 건식 다판클러치가 사용되고 있다. 하지만 건식 클러치의 경우 진동에 대한 문제가 발생하여 승차감에 영향을 주게 된다. 이를 해결하기 위해 4륜 구동장치의 핵심부품인 트랜스퍼케이스에 있는 다판클러치의 체결시 발생하는 충격을 저감시키고자 MR유체가 적용된 다판클러치를 제안한다. MR 다판클러치는 유체커플링 모드와 압착모드를 가지게 되며, 최적 설계를 위해 토크모델을 유도하였다. 다판클러치의 설계변수를 최적화를 위해 Ansys Maxwell을 이용하여 해석을 수행하였고, 전자기장 해석은 디스크와 플레이트의 수를 변경하였을 때 자기장의 세기를 확인하였으며, 자기장의 세기는 최대 0.45 Tesla가 도출되었다. 이를 토크방정식에 적용하여 플레이트 사이 간격을 2mm로 플레이트의 내경과 외경을 각각 45mm와 55mm로 선정하였다. 이와 같이 본 논문에서는 MR 다판클러치의 성능을 극대화할 수 있는 최적 설계기법을 제안하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권8호
• /
• pp.1149-1156
• /
• 2008

The principle of self clamping friction clutch is presented in this paper and the transmitted torque capacity is also calculated. In order to enlarge the friction force, a part of rotating force of driving side is converted to normal force of friction materials by clamping arm. The increased normal force of friction materials assures the large friction force and the transmitted torque capacity of clutch becomes large. The self clamping friction clutch is adopted in the tube type air pressure clutch and the condition of stability is investigated. It is proven that the inclined angle of clamping arm and the friction factor of friction materials are the essential elements in stability and torque capacity of self clamping friction clutch. The transmitted torque capacity of self clamping friction clutch is compared with air pressure clutch. The normal force of friction lining is magnified by 1/(1-k) and the transmitted torque capacity is also magnified with same proportion comparing with air pressure clutch. The larger the friction factor of friction lining, the larger the magnification factor. The longer the clamping arm, the smaller the magnification factor. It must be also noted that the value of k=${\mu}Y/X$ is the criterion of stability. If the value of k=${\mu}Y/X$ is greater than or equal to 1, the self clamping friction clutch is unstable and it can not be used as clutch.

• Tribology and Lubricants
• /
• 제33권2호
• /
• pp.71-78
• /
• 2017

The drag torque in the wet clutch system of a dual clutch transmission system is investigated because it is relatively high, up to 10 of the total output torque of the engine, even when the clutch is in the disengagement state with zero torque transfer. Drag torque results from the shear resistance of the DCTF between the friction pad and separator plate. To reduce the drag torque for ensuring fuel economy, the groove pattern of the wet clutch friction pad is designed to have a high flow rate through the pattern groove. In this study, four types of groove patterns on the friction pad are designed. The volume fraction of the DCTF (VOF) and hydrodynamic pressure developments in the gap between the friction pad and separator plate are computed to correlate with the computation of the drag torque. From the computational results, it is found that a high VOF and hydrodynamics increase the drag torque resulting from the shear resistance of the DCTF. Therefore, a patterned groove design should be used for increasing the flow rate to have more air parts in the gap to reduce the drag torque. In this study, ANSYS FLUENT is used to solve the flow analysis.