• Journal of Advanced Marine Engineering and Technology
• /
• 제41권1호
• /
• pp.118-124
• /
• 2017

본 연구대상 디젤기관의 연접봉 볼트, 크랭크 핀 베어링 볼트 등의 손상원인을 조사 분석하기 위하여 수행한 현장검사, 파손부에 대한 시험 및 고찰, 참고문헌 및 연구자의 경험 등을 통하여 다음과 같은 결론을 얻었다. 파손된 크랭크 핀 베어링 볼트는 연접봉 볼트보다 늦게 파손된 것으로 추정된다. 파손된 연접봉 볼트는 충격적인 하중에 의해서 취성파괴된 것이 아니고, 비정상적인 반복하중(예를 들어 체결 볼트의 풀림 등)에 의해서 피로파괴가 되었다는 것을 그 파단면의 모습을 통하여 알 수 있다. 파손된 연접봉 볼트용 U 너트는 윤활유(고착방지제)의 부적절한 사용, 각 실린더와 연접봉 별로 구분되어 사용되지 않았던 것 등으로 인하여 표면 상태가 불량하게 되었고, 이것은 연접봉 볼트의 파손사고에 영향을 미쳤을 가능성이 있다고 할 수 있다. 그리고 파손된 국내 제작품인 연접봉 볼트와 크랭크 핀 베어링 볼트의 기계적 성질, 전조공정 등은 해당 볼트의 설계요건에 적합하다고 할 수 있다.

• 한국정밀공학회지
• /
• 제31권8호
• /
• pp.715-720
• /
• 2014

Recently, surface texturing technologies have been widely used in lots of industries to increase the machinery efficiency. In this research, the lubrication characteristics of a crank shaft pin turner bearing with dimples were studied. When increasing the dimples, the load carrying capacity due to the increased pressure was increased because those have sealing effects. Also, the run-out error of the bearing was decreased. Therefore, it is important to consider the depth, the number and the distribution of dimples when designing the hydrostatic journal bearing.

• Tribology and Lubricants
• /
• 제27권5호
• /
• pp.256-263
• /
• 2011

Bearings of marine engines are operated under severe conditions because of dynamic load and low sliding speed. This paper deals with lubrication analysis of a crank pin bearing for a marine diesel engine. Journal center locus and oil film thickness are compared of crank pin bearing. In the past researches, journal bearings have been studied only about the surface of bearing. In addition to this conventional research, this paper analyzes the effect of roundness error of a journal and a bearing on the minimum film thickness. Numerical analysis has been studied by using Reynolds equation and also Half-Sommerfeld condition is applied as boundary condition. Futhermore, this study investigates the effect of roundness error change on the minimum film thickness. The results demonstrate that the bigger amplitude of roundness error yields, the lower minimum oil film thickness is. In comparison to previous research considered a journal and a bearing individually, the results considering a journal and a bearing together show that amplitude of roundness error of journal has very little effect on the minimum oil film thickness.

• Tribology and Lubricants
• /
• 제34권3호
• /
• pp.93-107
• /
• 2018

The purpose of Part I of this study is to find the potential region of wear scarring on engine journal bearings operating at a constant angular crank shaft velocity under firing conditions. To do this, we calculate the applied loads and eccentricities of a big-end journal bearing installed on a four-stroke and four-cylinder engine at every crank angle. Then, we find potential wear regions, such as a minimum oil film thickness, at every crank angle below most oil film thickness scarring wear (MOFTSW) obtained based on the concept of the centerline average surface roughness. Thus, the wear region is defined as a set of each film thickness below the MOFTSW at every crank angle. In this region, the wear volume changes according to the wear depth and wear angle, depending on the minimum oil film thickness at every crank angle. The total wear volume is the summation during one cycle. Graphical views of the region in the two-dimensional coordinates show the crank angle and bearing angle along the journal center path, indicating the position of the minimum oil film thickness. The results of wear analysis show that the possible wear region is located at a few tens of angles behind the upper center of a big-end bearing at maximum power rpm.

• 한국정밀공학회지
• /
• 제29권2호
• /
• pp.139-146
• /
• 2012

A multi-tasking machine tool for large scale marine engine crankshafts has been developed together with design technologies for its special devices. Since work pieces, that is, crankshafts to be machined are big and heavy; weight of over 100 tons, length of 10 m long, and diameter of over 3.5 m, several special purpose core devices are necessarily developed such as PTD (Pin Turning Device) for machining eccentric pin parts, face place and steady rest for chucking and resting heavy work pieces. PTD is a unique special purpose device of open-and-close ring typed structure equipped with revolving ring spindle for machining eccentric pins apart from journal. In order to achieve high rigidity of the machine tool, structural design optimization using TMSA (Taguch Method based Sequential Algorithm) has been completed with FEM structural analysis, and a hydrostatic bearing system for the PTD has been developed with theoretical hydrostatic analysis.

• Tribology and Lubricants
• /
• 제14권3호
• /
• pp.87-93
• /
• 1998

Crank pin bearing in two-stroke marine diesel engine is operated under quite severe conditions since the elements are big and heavy and the sliding speed is very slow. Therefore it is very difficult to form oil film. In this paper, two types of bearings with different groove shape are compared. One has circumferential oil groove at lower position and the other has lengthwise oil groove at upper position. Bearing clearance, oil inlet pressure and length to diameter ratio are selected as design parameters. Locus of journal center and minimum oil film thickness are investigated to compare two cases.

• Tribology and Lubricants
• /
• 제21권1호
• /
• pp.39-45
• /
• 2005

Investigation of the mass effect on the journal traces in the clearance of engine bearing has been performed for better design of mass distribution of crank system components such as crank pin, piston, con-rod, balance weight, crank throw weight, etc. as well as for better oil reaction behaviors to the applied forces from the cylinder pressures on the bearing. In this preliminary study, crank pin traces in the engine bearing clearance are computed by varying the equivalent magnitude of crank pin mass that includes the masses of crank pin, piston, con-rod. etc.. while most previous studies regarding journal traces in the bearing clearance neglect the inertia effects of crank pin mass. Although the inertia effect of pill mass is negligibly small compared to viscous force by ${\pi}bearing$ theory, it is found that it gives a great amount of influences on the journal traces in full bearing computation $(2\pi\;bearing\;theory)$ under the dynamic loading conditions.