• Journal of the Korea Concrete Institute
• /
• v.21 no.3
• /
• pp.275-282
• /
• 2009

The effects of surface treatment method of reinforcing fiber on the bonding strength between carbon fiber reinforced polymer rebar (CFRP rebar) and high strength concrete have been evaluated in this study. The structural PVA fiber is coated with a proprietary hydrophobicoiling agent and crimped type polyolefin based structural synthetic fiber is deformed with a geometrical modification were used for the reinforcing fiber. The compressive tests have been performed to evaluate the strength property of high strength concrete depending on the surface treatment method of fiber. The bonding property between the high strength concrete and the CFRP rebar was evaluated by means of direct bonding test. The test results indicated that the surface treatment method of fiber effect on the bonding behavior of high strength concrete and CFRP rebar. Also, as the development and propagation of splitting cracks were controled by adding fibers into the high strength concrete, the bonding behavior, bond strength and relative bonding strength of CFRP rebar and high strength concrete were significantly improved.

• Journal of the Korea Concrete Institute
• /
• v.13 no.5
• /
• pp.507-515
• /
• 2001

Significant improvements in bond strength between new and existing concrete can be achieved through the modification of the new concrete by latex. This study focuses on the investigation of bond strength of latex modified concrete. Pull-out bond test and uniaxial direct tensile bond test are adopted for evaluating the adhesion characteristics of latex modified concrete to conventional concrete substrate. The main experimental variables are test methods, latex-cement ratio, surface preparations and moisture levels. The results are as follows; The increase of latex-cement ratio substantially improves the adhesion between latex modified concrete and substrate. The effects of surface preparation at substrate into the bonding of latex modified concrete are quite different according to the conditions of surfaces. Thus, an adequate surface preparations are essential for good bond strength. Because the moisture level of the substrate may be critical to achieving bond, optimum moisture condition for a conventional concrete has evaluated in this study. The saturated condition of surface is the most appropriate moisture level among the considered, followed by dry condition and wet condition.

• International Journal of Highway Engineering
• /
• v.11 no.4
• /
• pp.95-105
• /
• 2009

This study was conducted to investigate the effects of concrete flexural strength and surface smoothness, which were pay factors of concrete pavements, on pavement performance, and to develop the methodologies to determine the proper allowable ranges according to the magnitudes of those pay factors. The concrete flexural strength was analyzed using the AASHTO, power, and linear fatigue failure models, and the surface smoothness was analyzed for the roughness indices of PSI, IRI, and PrI using the AASHTO model. The analysis results showed that the allowable range of the flexural strength should be determined using the rate between the deficiency and strength, and the penalty should be linearly proportional to the strength deficiency rate because the linear relationship between the strength deficiency rate and the reduction in pavement life was observed. As the initial surface smoothness became better, the smoothness deficiency rate should be larger. The penalty due to the surface smoothness deficiency should also be linearly proportional to the smoothness deficiency rate.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.162-162
• /
• 2011

표면파 속도 측정은 근래 토목분야에서는 비파괴 지반조사기법으로 활용되고 있다. 최근에는 디지털 신호처리기술의 발달과 함께, 더욱 정확해진 자료분석 알고리즘을 통하여 표면파 탐사관련 기술이 향상되어 3차원의 공간연속적인 시험이 가능해졌다. 본 연구는 표면파의 분산 특성을 이용하여 콘크리트 구조물의 깊이별 강성평가를 하는 SASW(Spectral Analysis of Surface Waves)기법과 STFT(Short time Fourier Transform)과 HWT(Harmonic Wavelet Transform)를 이용한 주파수영역에서의 공진주파수를 통한 부재평가 기법인 IE(Impact Echo)기법을 이용하여 대상부재의 강도평가를 수행하기 위한 시제품 개발을 수행하였다. 시제품은 메인프레임과 2개의 센서로 이루어져 측정을 수행하며 측정장치와 DAQ장치 및 S/W로 구성되어 있다. 메인프레임의 진동특성영향을 제거하기 위하여 2개의 센서는 프레임과 띄움구조로 설계하였고 센싱하는 위치는 대상 재료의 밀착되어 계측할 수 있도록 설계하였다. 탄성파를 계측하여 대상 재료의 깊이별 측정된 표면파의 속도를 계측하며 개발된 시제품의 구조물별 적용성 평가를 위한 실험을 수행하였고 평균 표면파 속도를 통해 추정한 콘크리트 두께와 결함 및 강도 추정의 적용성을 평가하였다. 시제품을 이용해 시험콘크리트 표면파를 측정한 결과 SASW기법을 이용하여 깊이에 대한 위상속도 분포와 IE기법의 결과로 개발된 시제품의 합리적 적용성이 평가되었다. 그러나 재료의 강도추정에 있어서는 각각 알고리즘의 주파수분석 요소들에 의해 변동되는 경향을 보여 추후 많은 테스트를 통해 속도-강도 추정의 회귀곡선식을 S/W에 탑재시키고 다양한 방법으로 조합하는 알고리즘으로 신뢰성있는 강도추정을 위한 알고리즘을 개발하여야 한다.

• International Journal of Highway Engineering
• /
• v.3 no.4 s.10
• /
• pp.117-126
• /
• 2001

In this research, evaluation of adhesion in tension property of SBR-modified concrete to ordinary portland cement concrete was conducted with uniaxial direct tensile bond test which was proposed by Kuhlmann. A test set-up was fabricated in order to minimize the eccentric force by introducing a joint which might fully rotate. The main experimental variables were cement-latex ratios, surface preparations and moisture levels. The results obtained were as follows: The LMC specimen at 15% latex-cement ratio increased the adhesion in tension by range of 37% compared to that of conventional cement concrete. This might be due to latex film formed between cement paste and aggregate. The effects of surface preparation on bond of latex modified concrete to conventional concrete were significant at the conditions by sand paper and wire brush. A better bond could be achieved by rough surface rather than smooth. The saturated and surface dry (SSD) condition were considered to be the most appropriate moisture level followed by wet, finally by dry. Thus, a proper surface preparation and moisture level are quite necessity in order to obtain better bonding at LMC overlay.

• Applied Chemistry for Engineering
• /
• v.21 no.4
• /
• pp.457-462
• /
• 2010

In this research, the effects of the concrete superplastizers on the wettability of cement particle and concrete strength were studied. The wettability of the cement particles strongly depended on the type of the superplastizer. When the superplastizer had a higher wettability with the cement particles, it revealed a good fluidity of the concrete mortar and a higher concrete strength. Non-ionic superplastizers (polycarboxylic type) had a relatively good performance on the mortar fluidity and concrete strength properties compared to anionic superplastizers (lignosulfate, sulfonated naphthalene formaldehyde, sulfonated melamin formaldehyde). It was observed that the blending of the polycarboxylic and the lignosulfate type concrete superplastizers resulted in synergistic effects on the concrete mortar fluidity and concrete strength properties.

• Magazine of the Korea Concrete Institute
• /
• v.19 no.2
• /
• pp.66-70
• /
• 2007

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.989-992
• /
• 2008

In this paper, we are presenting a case that integrates ultra high strength concrete(150MPa) with surface-exposed concrete. Ahead of the field application, we carried out laboratory experiment and B/P Test for a basic property of concrete(slump flow, air content, 50cm flow time, elapse time change and compression strength) and productivity. The next, we conducted Mock-up Test using simulation specimen to evaluate infilling, surface-finishing and hydration heat of concrete. We had satisfactory results for a basic property and hydration heat of concrete. However at the time of field application, it was occurred rupture of formwork because of high lateral pressure of concrete, and then formwork was reinforced and case-in-place time was adjusted. And regardless of low and high frequency vibration, it occurred to surface-pockmark. In case that applies ultra high strength concrete to surface-exposed concrete, we estimate that it is important of systematic management and improvement of construction.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.1
• /
• pp.111-116
• /
• 2022

Recently, building structures tend to be super high-rise and large-scale with the development of concrete technology. When high-rise building is constructed of reinforced concrete structure, it has a disadvantage that its own weight increases. Light weight aggregate(LWA) was developed to compensate for these shortcomings. Manufacturing concrete using these light weight aggregates has the advantage of reducing the self weight of the reinforced concrete structure, but has a disadvantage in that the strength of the concrete is reduced. In this study, an experimental study was conducted to investigate the strength characteristics of hardened cement according to the presence or absence of surface coating of lightweight aggregates. As a result, in terms of compressive strength, the surface-coated lightweight aggregate exhibited higher strength than the uncoated lightweight aggregate. Also, it was considered that this is because the interfacial voids of the surface coated lightweight aggregate mixed cement hardened body were filled with blast furnace slag fine powder particles.

• International Journal of Highway Engineering
• /
• v.11 no.2
• /
• pp.1-15
• /
• 2009

Surface of exposed aggregate concrete pavements is consists of exposed coarse aggregate by removing upper 2$\sim$3mm mortar of concrete slab. Exposed aggregate concrete pavements have advantages of maintaining low-noise and adequate skid-resistance level during the performance period. In order to provide the successful exposed concrete aggregate pavement, uniform distribution of the coarse aggregate on pavement surface through adequate the mix design and exposing method. The mix design in concrete pavement is generally designed on the basis of strength, but mix design of exposed aggregate pavement employed in this study includes the consideration of noise and skid resistance, as well as strength. Smaller of maximum coarse aggregate is known to be effective for reduce noise level. Optimum mix design and exposing method of fine-size exposed aggregate portland cement concrete pavement that can reducing the noise and maintain the adequate level of skid resistance are proposed in this study. To consider the variation of optimum exposing time due to the hardening speed of mortar by climatic condition, quantitative is also suggested measurement of hardening state.