• Journal of the Korean institute of surface engineering
• /
• v.49 no.1
• /
• pp.32-39
• /
• 2016

In this study, Al and Zn arc thermal spray coatings were carried out onto the substrate of SS400 steel to improve corrosion resistance and durability of hull structural steel for ship in marine environment. Therefore cavitation-erosion test was conducted to evaluate the durability of painted and thermal spray coated specimens. And then the damaged surface morphology and weight loss were obtained to compare with each other, respectively. As a result, the painted specimen was the poorest cavitation resistance characteristics because surface damage behavior appeared to be exfoliated in bulk shape during the cavitation experiment. And Zn thermal spray coating layer presented the significant surface damage depth due to relatively low surface hardness and local cavitation damage tendency. On the other hand, as a result of the weight loss analysis, the painting layer presented the poorest cavitation resistance and the Al thermal spray coating layer relatively showed the best results after cavitation experiment.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.2
• /
• pp.70-74
• /
• 2012

In thermal barrier coating (TBC) systems, the life of the coating depends on thermally grown oxide (TGO) layer because most of the failure of TBCs occurs when TGO growth increases. In order to inhibit TGO growth, process was additionally carried out before the heat treatment of the TBC coating layer at $1200^{\circ}C$ in air. In the additional process, heat treatment in vacuum furnace of < $10^{-5}$ torr was conducted for 7 h and 14 h before the heat treatment. The area and length of TGO, as well as the crack length in the TBC were characterized using a scanning electron microscope (SEM). The TGO thickness and crack of specimens pre-heat treated in vacuum furnace were reduced by 45% compare to those heat treated in furnace. Consequently, pre-heat treatment in a vacuum furnace process lead to effective inhibition of growth of the TGO.

• 연구논문집
• /
• s.24
• /
• pp.63-79
• /
• 1994

This article reports a experimental study of the method to achieve a bond joint at lower temperature in a short time. DC magnetron sputtering of Sn, Sn/Pb, Sn/In and Sn/Cu on copper substrate was provided as an interlayer for Cu to Cu bonding under the air environment. Various examination was conducted and investigated on the effect of experimental parameters such as coating materials, coating time(or coating thickness), bonding temperature and bonding time etc. Bonding was performed at the temperature of $210^\circC-320^\circC$ for 0sec and interfacial reaction between the coated layer and copper substrate was examined using optical, scanning electron microscope and x-ray diffractometer. From the obtained results, it was found that intermetallic compounds layer consisted of $\eta-phase(Cu_6Sn_5)$ and $\beta-phase(Cu_3Sn)$ was formed at the joint interface for almost all coating materials. But the dominant phase formed in the preetched Cu substrate coated with Sn was $\beta-phase$. A characteristic morphology looks like a reaction ring, which was believed as the strong interconnecting regions between two substrates, was found to be formed on the reaction surface of copper substrates. The morphologies and compositions of the intermetallics, which depends on the regions of the reaction surface, was appeared as greatly different. Based on above results, the new bonding process to make the joint at lower temperature for short time can be admitted as a feasible process.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.160-161
• /
• 2015

탄소 원자들이 육각형의 벌집 모양으로 배열된 그래핀은 강철보다 200배 이상 강하며, 다이아몬드보다 2배 이상 열전도율이 높으며, 구리보다 100배 이상 전기가 잘 통하며, 실리콘보다 100배 이상 전자가 빠르게 움직일 수 있는 장점이 있다. 그래핀의 이러한 기계적, 열적, 전기적 특성은 에너지 밴드 갭이 없는 그래핀의 전자구조에서 근거하고 있다. 그러나 이러한 에너지 밴드 갭이 없는 그래핀은 반도체가 아닌 준금속의 특성을 보이며, 전자산업의 핵심소자인 트랜지스터로의 상용화에 큰 장벽이 되고 있다. 이러한 그래핀의 단점을 보완하고자 그래핀 이외의 2D 물질에 주목하기 시작하였으며, 그 가운데 최근 $MoS_2$과 같은 Transiton-Metal dichalcogenide(TMD)에 대한 관심이 급증하고 있다. TMD 중 대표적인 물질인 MoS2는 단일 층이 직접 전이 밴드 갭을 가진 반도체로서 전자회로와 발광 다이오드에 이용될 잠재적 가능성을 가진 재료이다. 본 연구에서는 이러한 MoS2 박막 형성을 하기 위해서 대면적이고 저비용으로 만들 수 있는 spin coating을 이용하려고 한다. spin coating을 이용하여 박막을 얻기 위해서는 좋은 wettability가 필수적이므로 이를 개선하기 위하여 용액, 전처리에 따른 wettability를 비교한 후, 열처리를 하여 그 표면을 관찰하고 Raman spectroscopy를 이용하여 분석하여 최적의 조건을 찾기 위한 실험을 하였다.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.2
• /
• pp.81-92
• /
• 1996

The cementless fixation of bone ingrowth by porous coatings on artificial hip joint prostheses are replacing polymethylmethacrylate(PMMA) bone cement fixations. However, the major interests in the field of porous metal coating are environmental corrosivity accelerated by metal ion release, deterioration in the mechanical property of the coating, and the mechanical failure of the coatings as well as the substrate. Therefore, the selection of right materials for coatings and the development of porous coating techniques must be accomplished. Because of the existing problems in Ti and Ti alloys which are used extensively, this study is focused on the plasma spraying technique for coating on super stainless steel substrate. In order to determine the optimum conditions which satisfy the requirement for the porous coatings, under the plasma spraying, we selected the experimental parameters which extensively influenced on the characteristics of the coating through the pre-examination. Spray distance has been selected among 120, 160, and 200mm and primary gas flow rate among 70, 100, and 130 SCFH. Current and secondary gas($H_2$) flow rate was fixed at 400A, and 15 SCFH respectively. To understand the characteristics of the coatings, surface morphology, cross-sectional micro-structure, surface roughness, residual stress, and corrosion resistance were elucidated and the best conditions for the bone ingrowth improvement on artificial hip joint prostheses were found.

• Journal of the Korean institute of surface engineering
• /
• v.23 no.2
• /
• pp.24-29
• /
• 1990

The TiN filmms were deposited on the stainless steel substrates by BARE techinique in order to investigate the effects of process parameters such as source-to-substate distance (15-35cm), N2 pressure(4$\times$10-10 -1$\times$10-3mb)and bias voltage(O-2000V), on the deposition rate, the concentration ratio [N/Ti] and the surface color of the films. The deposition rate was deduced from the weight measurement, the [N/ti] ratio by ESCA. The deposition rate decreased with a relationship of=40.2/D2 where D was source-to-substrate distance. The effect of the bias voltage and the N2pressure on the deposition rate, however, appeared negligble. The [N/Ti] ratio was in the narrow range of 0.7 tp 0.8 It increased slightly with the N2 partial pressure and deceased with the source-to-substrate distance. It was confired by ESCA that a significant amount of oxygen and carbon was contaminated after deposition in the top surface of TiN films. The surface color of TiN film was changed from light gold yellow to reddish gold yellow with increasing [N/Ti] ratio.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1522-1523
• /
• 2007

MEMS(Micro Electro Mechanical Systems)기술과 니켈 전기도금 공정을 이용하여 수십 내지 수백개의 탐침소자를 갖는 프르브디바이스(probe device)를 제작하였다. 사용된 기판은 $4000{\AA}$의 oxide가 있는 p-type 실리콘 웨이퍼로서, 기판위에 NiCr과 Au를 증착한 후 PR 패터닝을 통하여 니켈을 전기도금법으로 도금하고 니켈 도금층을 제외한 부분의 NiCr과 Au를 식각함으로서 전류가 흐르는 라인(line)배선과 탐침소자가 세워질 라인을 형성하였다. 그 후 후막의 PR을 코팅하고 탐침소자가 세워질 부분을 패터닝 한 후 전기도금법을 이용하여 니켈 탐침소자를 제작하였다. 제작된 탐침소자 하나의 크기는 $60{\mu}m$의 폭과 $70{\mu}m$의 높이를 보이며, 탐침소자 전체의 크기는 $250{\mu}m$이고 탐침소자와 탐침소자 사이의 간격은 $50{\mu}m$로 제작되었다. 본 연구에서 제작된 탐침소자의 수는 25*2line으로서 총 50개 이지만 이러한 공정방식을 이용하고 탐침소자의 크기를 작게 제작한다면 하나의 프르브 디바이스에 수백 내지수천 개의 탐침소자를 제작할 수 있을 것이다.

• Journal of Power System Engineering
• /
• v.18 no.6
• /
• pp.58-63
• /
• 2014

This paper deals with the effects of counterpart materials on the wear behavior of thermally sprayed STS316 coatings. STS316 powders were flame-sprayed onto a carbon steel substrate. Dry sliding wear tests were performed using the applied loads of 15 N. AISI52100, $Al_2O_3$, $ZrO_2$ and $Si_3N_4$ balls were used as counterpart materials. Wear behavior of STS316 coatings against different counterpart materials were studied using a scanning electron microscope(SEM) and energy dispersive X-ray spectroscopy (EDS). The results show that the wear behavior of thermally sprayed STS316 coatings strongly depends on the type of counterpart material. Dominant wear mechanism was similar for all studied materials as failure of adhesion film except for Si3N4 used as counterpart material. In the case of Si3N4 used as counterpart material, dominant wear mechanism was abrasion.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.346-353
• /
• 2001

Zirconia powder containing 3 mol% yttria(3Y-PSZ) with and with out Fe$_2$O$_3$ addition was coated on tile cast iron substrate by plasma spraying method. The erosion experiments were performed at temperatures from $25^{\circ}C$ to $600^{\circ}C$. A gas blast type erosion tester was used to examine erosion behavior of the specimens. The results of 3Y-PSZ coatings showed that tile erosion rate had maximum value at 40$0^{\circ}C$. It coincided with tile results of phase transformation tetragonal phase to monoclinic phase caused by low temperature thermal degradation. The tensile stress relaxation and the micro-hardness improvement significantly influenced on the erosion rate at $600^{\circ}C$. In the case of Fe$_2$O$_3$ added 3Y-PSZ coatings, the erosion rate of tested at $25^{\circ}C$ showed maximum value at 5.0 mol% Fe$_2$O$_3$ added coating. This tendency is caused by the improvement of mechanical properties and the tensile residual stress. The erosion rate at 200'c and 400'L showed significantly decrease by Fe203 addition. This decrease is believed to be the stabilization of the tetragonal phase and the increase of micro-hardness.

• Tribology and Lubricants
• /
• v.25 no.1
• /
• pp.7-12
• /
• 2009

Coating brittle intermetallic compounds on metal can enlarge the range of their use. It is found that intermetallic compound coating layers made by only combustion synthesis in an electric furnace have porous multi-phase structures containing several intermediate phases, even though the coating layers show good wear resistance. In this study, dense $Ni_{3}Al$ single phase layer corresponding to the initial composition of the mixed powder is coated on two different ferrous materials by the diffusing treatment after combustion synthesis. After- ward, sliding wear behaviors of the coating layer are evaluated in comparison with that of the coating layer with porous multi-phase structure made by only combustion synthesis. As a result, the wear properties of the coating layer composed of dense $Ni_{3}Al$ single phase are considerably improved at the range of low sliding speed com- pared with that of the coating layer with porous multi-phase structure, particularly in the running-in wear region. This is attributed to the fact that wear of the coating layer is progressed by shearing as a sequence of adhesion, not by occurring of pitting on the worn surface due to having dense structure without pores.