Park, Jae Hwa;Hong, Yoon Pyo;Park, Cheol Woo;Kim, Hyun Mi;Oh, Dong Keun;Choi, Bong Geun;Lee, Seong Kuk;Shim, Kwang Bo
Journal of the Korean Crystal Growth and Crystal Technology
/
v.24
no.4
/
pp.135-139
/
2014
The hydride vapor phase epitaxy (HVPE) grown GaN samples to precisely measure the surface characteristics was applied to a molten KOH/NaOH wet chemical etching. The etching rate by molten KOH/NaOH wet chemical etching method was slower than that by conventional etching methods, such as phosphoric and sulfuric acid etching, which may be due to the formation of insoluble coating layer. Therefore, the molten KOH/NaOH wet chemical etching is a better efficient method for the evaluation of etch pits density. The grown GaN single crystals were characterized by using X-ray diffraction (XRD) and X-ray rocking curve (XRC). The etching characteristics and surface morphologies were studied by scanning electron microscopy (SEM). From etching results, the optimum etching condition that the etch pits were well independently separated in space and clearly showed their shape, was $410^{\circ}C$ and 25 min. The etch pits density obtained by molten KOH/NaOH wet chemical etching under optimum etching condition was around $2.45{\times}10^6cm^{-2}$, which is commercially an available materials.
Kim, Dae-Hoon;Kim, Guang-Lim;Jo, Hang-Dae;Park, Jong-Soo;Lee, Hyung-Keun
Korean Chemical Engineering Research
/
v.48
no.5
/
pp.660-667
/
2010
In this research polyimide, Matrimid 5218, hollow fiber membrane was used to recover sulfur hexafluoride($SF_6$) which is one of the six greenhouse gases from $N_2/SF_6$ mixture gas. Fibers were spun from using dry-wet phase inversion method. The module was manufactured by fabricating fibers after surface coating with silicone elastomer. The scanning electron microscopy(SEM) studies showed that the produced fibers typically had an asymmetric structure; a dense top layer supported by a sponge-like substructure. The developed module had a permeance of 0.78-1.36 GPU for $N_2$ with $N_2/SF_6$ selectivity of 2.44-5.08 at various pressure and temperature. For recovery of $SF_6$, a membrane module and 10 vol.% $SF_6$ from $N_2/SF_6$ mixture gas was used. The effects of various operating condition such as pressure, temperature, and retentate side flow rate were tested. When pressure and temperature were increased and retentate flow rate was decreased, the $SF_6$ purity in recovered gas was increased up to 37.5 vol.% with decreasing recovery ratio. When retentate flow rate was increased pressure and temperature was decreased, the $SF_6$ recovery ratio in retentate side was increased up to 89% with decreasing the $SF_6$ purity in retentate side.
No, Ho-Gyun;Park, Mi-Na;Lee, Seung-Min;Bae, Su-Gang;Kim, Tae-Uk;Ha, Jun-Seok;Lee, Sang-Hyeon
Proceedings of the Korean Vacuum Society Conference
/
2016.02a
/
pp.131-131
/
2016
기원전 5000년 이집트에서부터 시작된 도금은 시간이 지남에 따라 점점 발전하여, 1900년대에 들어 전기를 이용한 도금공정이 개발되었고, 현재 뿌리산업으로써 각종 제조업에 널리 이용되고 있다. 도금 공정은 금속을 부식으로부터 보호하고, 제품의 심미성과 기능성, 생산성 등을 높이기 위해 주로 이용된다. 전주도금 공정은 완벽하게 동일한 형태의 생산품을 다량으로 제작 할 수 있기 때문에, 그 높은 생산성으로 주목 받고 있다. 특히, 나노/마이크로 크기의 정밀 소자 등을 가공하는 차세대 기술인 LIGA공정과 접목이 가능하다는 장점이 있다. 몰드를 이용하여 복제하는 방식인 전주 도금은 도금공정이 끝난 후 몰드와 완성된 제품을 분리해내는 추가공정이 필연적으로 발생하게 되는데, 둘 사이의 접착력을 낮추기 위하여 몰드의 표면에 이형박리제를 도포하게 된다. 이형박리제로는 전기가 잘 흐르면서 접착력이 낮은 이산화 셀렌이나 중크롬산이 주로 이용되지만, 원활한 박리를 위해서는 그 두께가 30 um 이상 확보되어야 하기 때문에 정밀한 미세구조 전주도금이 어렵다는 문제점이 있다. 또한 이와 같은 화학 약품들은 매우 유독하기 때문에 추가적인 폐수 처리 공정이 필요하며, 작업자의 안전을 위협하고 심각한 환경 오염을 초래한다는 추가적인 문제가 발생한다. 따라서, 매우 얇고 친 환경적이며 안전한 전주도금 이형박리제에 대한 연구가 요구되고 있다. 본 연구에서는 전주도금 몰드로 사용한 구리의 표면에 TCVD를 이용하여 단일 층 그래핀을 성장시킨 후, 그래핀이 코팅된 몰드에 구리를 전주도금하여 박리하였다. 박리 후 그래핀은 몰드에 손상 없이 남아있는 것을 Raman microscopy를 통해서 확인하였고, 몰드와 그래핀 사이의 접착력 (약 $0.71J/m^2$)에 비해 그래핀과 전주도금 샘플간에 낮은 접착력 (약 $0.52J/m^2$)을 갖는 것을 확인하였다. 이와 같이 낮은 접착력을 통해 박리 시 표면구조의 손상 없이 정밀한 구조의 미세 패턴구조를 형성할 수 있었다. 전주도금을 이용한 전극 형성과 고분자와의 융합을 통해 유연기판을 제작하여 bending 실험을 진행하였다. $90^{\circ}$의 bending 각도로 10000회 이하에서는 저항의 변화가 없었고, LED chip을 mounting한 후 곡률반경 4.5 mm까지 bending을 진행하여도 이상 없이 LED가 발광하는 것을 확인하였다. 위와 같은 전주도금 공정을 이용하여 고집적 전자기기, 광학기기, 센서기기 등의 다양한 어플리케이션의 부품제조에 활용될 수 있을 것으로 기대한다.
Proceedings of the Korean Vacuum Society Conference
/
2016.02a
/
pp.256-256
/
2016
기존의 디스플레이 기슬은 마스크를 통해 특정 부분에만 유기재료를 증착시키는 방법을 사용하였으나, 기판의 크기가 커짐에 따라 공정조건에 제약이 발생하였다. 이를 해결하기 위해 최근 용액 공정에 대한 연구가 활발히 진행되고 있다. 용액 공정은 기존 진공 증착 방식과 비교하였을 때 상온, 대기압에서 증착이 가능하며 경제적이고, 대면적 균일 증착에 유리하다는 장점이 있다. 반면, 용액 공정으로 제작한 소자는 시간이 지남에 따라 점차 전기적 특성이 변하는 aging effect를 보인다. Aging effect는 용액에 포함된 C기와 OH기 기반의 불순물의 영향으로 시간의 경과에 따라서 문턱전압, subthreshold swing 및 mobility 등의 전기적 특성이 변하는 현상으로 고품질의 박막을 형성하기 위해서는 고온의 열처리가 필요하다. 지금까지 고품질 박막 형성을 위한 열처리는 퍼니스 (furnace) 장비에서 주로 이루어졌는데, 시간이 오래 걸리고, 상대적으로 고온 공정이기 때문에 유리, 종이, 플라스틱과 같은 다양한 기판에 적용하기 어렵다는 단점이 있다. 따라서, 본 연구에서는 $100^{\circ}C$ 이하의 저온에서도 열처리가 가능한 microwave irradiation (MWI) 방법을 이용하여 solution-processed InGaZnO TFT를 제작하였고, 기존의 열처리 방식인 furnace로 열처리한 TFT 소자와 aging effect를 비교하였다. 먼저, solution-processed IGZO TFT를 제작하기 위해 p type Si 기판을 열산화시켜서 100 nm의 SiO2 게이트 산화막을 성장시켰고, 스핀코팅 방법으로 a-IGZO 채널층을 형성하였다. 증착후 열처리를 위하여 1000 W의 마이크로웨이브 출력으로 15분간 MWI를 실시하여 a-IGZO TFT를 제작하였고, 비교를 위하여 furnace N2 gas 분위기에서 $600^{\circ}C$로 30분간 열처리한 TFT를 준비하였다. 제작된 직후의 TFT 특성을 평가한 결과, MWI 열처리한 소자가 퍼니스 열처리한 소자보다 높은 이동도, 낮은 subthreshold swing (SS)과 히스테리시스 전압을 가지는 것을 확인하였다. 한편, aging effect를 평가하기 위하여 제작 후에 30일 동안의 특성변화를 측정한 결과, MWI 열처리 소자는 30일 동안 문턱치 전압(VTH)의 변화량 ${\Delta}VTH=3.18[V]$ 변화되었지만, furnace 열처리 소자는 ${\Delta}VTH=8.56[V]$로 큰 변화가 있었다. 다음으로 SS의 변화량은 MWI 열처리 소자가 ${\Delta}SS=106.85[mV/dec]$인 반면에 퍼니스 열처리 소자는 ${\Delta}SS=299.2[mV/dec]$이었다. 그리고 전하 트래핑에 의해서 발생하는 게이트 히스테리시스 전압의 변화량은 MWI 열처리 소자에서 ${\Delta}V=0.5[V]$이었지만, 퍼니스 열처리 소자에서 ${\Delta}V=5.8[V]$의 큰 수치를 보였다. 결과적으로 MWI 열처리 방식이 퍼니스 열처리 방식보다 소자의 성능이 우수할 뿐만 아니라 aging effect가 개선된 것을 확인할 수 있었고 차세대 디스플레이 공정에 있어서 전기적, 화학적 특성을 개선하는데 기여할 것으로 기대된다.
Journal of Advanced Marine Engineering and Technology
/
v.39
no.3
/
pp.223-229
/
2015
Surface modification is a technology to form a new surface layer and overcome the intrinsic properties of the base material by applying thermal energy or stress onto the surface of the material. The purpose of this technique is to achieve anti-corrosion, beautiful appearance, wear resistance, insulation and conductance for base materials. Surface modification techniques may include plating, chemical conversion treatment, painting, lining and surface hardening. Among which, a surface modification process using electrolytes has been investigated for a long time in connection with research on its industrial application. The technology is highly favoured by various fields because it provides not only high productivity and cost reduction opportunities, but also application availability for components with complex geometry. In this study, an electrochemical experiment was performed on the surface of 5083-O Al alloy to determine an optimal electrolyte temperature, which produces surface with excellent corrosion resistance under marine environment than the initial surface. The experiment result, the modified surface presented a significantly lower corrosion current density with increasing electrolyte temperature, except for $5^{\circ}C$ of electrolyte temperature at which premature pores was created.
Journal of the Korea Academia-Industrial cooperation Society
/
v.19
no.1
/
pp.105-112
/
2018
This paper proposes a method for fabricating heatable glass using the conduction characteristics of metal thin films deposited on the surface of Low-e(Low emissivity) glass. The heating value of Low-e glass depends on the Joule heat caused by Low-e glass sheet resistance. Hence, its prediction and design are possible by measuring the sheet resistance of the material. In this study, silver electrodes were placed at 50 mm intervals on a soft Low-e glass sample with a low emissivity layer of 11 nm. This study measured the sheet resistance using a 4-point probe, predicted the power consumption and heating value of the Low-e glass, and confirmed the heating performance through fabrication and experience. There are two conventional methods for manufacturing heatable glass. One is a method of inserting nichrome heating wire into normal glass, and the other is a method of depositing a conductive transparent thin film on normal glass. The method of inserting nichrome heating wire is excellent in terms of the heating performance, but it damages the transparency of the glass. The method for depositing a conductive transparent thin film is good in terms of transparency, but its practicality is low because of its complicated process. This paper proposes a method for manufacturing heatable glass with the desired heating performance using Low-e glass, which is used mainly to improve the insulation performance of a building. That is by emitting a laser beam to the conductive metal film coated on the entire surface of the Low-e glass. The proposed method is superior in terms of transparency to the conventional method of inserting nichrome heating wire, and the manufacturing process is simpler than the method of depositing a conductive transparent thin film. In addition, the heat characteristics were compared according to the patterning of the surface thin film of the Low-e glass by an emitting laser and the laser output conditions suitable for Low-e glass.
Prismatic reflective sheets were prepared using microprisms, and their retroreflection and structural properties were investigated and compared with encapsulated lens type reflective sheets based on glass beads. As prepared, the prismatic reflective sheets show well arranged array of microprisms. The arrangement of glass beads in encapsulated lens type reflective sheets is also found to be uniform without any cracks. However, during the coating process of the PET layer, the beads are coming out and the gaps are formed due to the application of high pressure. Even though the preparation method for reflective sheets based on microprisms is similar to that of reflective sheets based on glass beads, the method is relatively simple and cost effective, and also needs less time. Prismatic reflective sheets show higher coefficient of retroreflection from all entrance angles compared to reflective sheets based on glass beads. The results prove that the prismatic reflective sheets can be used for preparing the traffic sign boards to secure a clear view.
Journal of the Korean Crystal Growth and Crystal Technology
/
v.21
no.4
/
pp.147-152
/
2011
ZnO nanorods fabricated on a Zn substrate pre-coated with ZnO as a seed layer by the hydrothermal method were studied mainly as a function of ZnO precursor concentration. Characteristic features by using field-emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD) were investigated to define the changed micro-structure and crystalline phase of the ZnO nanorods according to the experimental conditions. The nanorod morphology strongly depended on the precursor concentration. For example, ZnO nanorods vertically aligned with a hexagonal (002) oriented structure with a diameter of 600~700 nm and length of $6.75{\mu}m$ were clearly observed at the highest concentration of 0.015 M. The strong hexagonal structure was believed to be associated with the highest photoluminescene (PL) intensity and a promising voltage value of ca. 6.069 V at $1000{\mu}A$.
Kim, Jin-Ho;Lee, Min;Hwang, Jong-Hee;Lim, Tae-Young;Kim, Sae-Hoon
Journal of the Korean Crystal Growth and Crystal Technology
/
v.19
no.6
/
pp.288-292
/
2009
Hydrophobic/hydrophilic patterned substrates were fabricated on a glass substrate by a liquid phase deposition (LPD) method. Hydrophobic surface was obtained by modifying ZnO thin films with a rough surface using a fluoroalkyltrimethoxysilane (FAS) and hydrophilic surface was prepared by decomposing FAS on an exposed to UV light. The hexagonal ZnO rods were perpendicularly grown by LPD method on glass substrates with a ZnO seed layer. The diameter and thickness of hexagonal ZnO rods were increased as a function of increases of immersion time. The surface morphology, thickness, crystal structure, transmittance and contact angle of prepared ZnO thin films were measured by field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), UV-visible spectrophotometer (UV-vis) and contact angle measurement. Hydrophilic ZnO thin films with a contact angle of $20^{\circ}{\sim}30^{\circ}$ were changed to a hydrophobic surface with a contact angle of $145^{\circ}{\sim}161^{\circ}$ by a FAS surface treatment. Prepared hydrophobic surface was pattered by an irradiation of UV light using shadow mask with $300\;{\mu}m$ or 3 mm dot size. Finally, the hydrophobic surface exposed to UV light was changed to a hydrophilic surface.
Kim, Deuk-Han;Yoo, Se-Hoon;Lee, Chang-Woo;Lee, Taek-Yeong
Journal of the Microelectronics and Packaging Society
/
v.17
no.2
/
pp.55-61
/
2010
The device with tantalum silicide heater were bonded by Ag paste and Au SBB(Stud Bump Bonding) onto the Au coated substrate. The shear test after Au ABB and the thermal performance under current stressing were measured. The optimum condition of Au SBB was determined by fractured surface after die shear test and $350^{\circ}C$ for substrate, $250^{\circ}C$ for die during flip chip bonding with bonding load of about 300 g/bump. With applying 5W through heater on the device, the maximum temperature with Ag paste bonding was about $50^{\circ}C$. That with Au SBB on Au coated Si substrate showed $64^{\circ}C$. The difference of maximum temperatures is only $14^{\circ}C$, even though the difference of contact area between Ag paste bonding and Au SBB is by about 300 times and the simulation showed that the contact resistance might be one of the reasons.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.