• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.7
• /
• pp.1194-1203
• /
• 2000

A magnetic field exposure system that generates 60 Hz magnetic fields from 1 mG to 5 G was designed and constructed for small-sized animal study. In order to investigate as many animals as possible at one series of test, uniform magnetic fields are required at wide living area of the animals. In this article, a cubic shaped field exposure system with three animal living floors was designed, which offers about 50 seating capacity. For calculation of magnetic fields inside the cage, a three-dimensional calculation program was developed. Using this, optimum electric current ratio of inner coil to outer coil and position of each coil were determined. Meanwhile, inductance of the exposure system was calculated for the design of power supply. The field measurement results of the manufactured exposure system showed that the difference between maximum and minimum magnetic field at the testing floors was less than 3%, which strongly demonstrated the field exposure system was good for small sized animal study.

• Journal of the Korean Vacuum Society
• /
• v.18 no.3
• /
• pp.176-185
• /
• 2009

The realization and the performance of ICP source are strongly affected by its electrical impedance and the electric/magnetic field distribution. The ICP source impedance is determined by the antenna impedance and the plasma one. It is preferred to keep the imaginary impedance between -100 ohm to 100 ohm, since it should be avoided the high voltage formation on the antenna and abrupt impedance variation during the thin film process. The plasma uniformity is affected by the electric and magnetic field which is formed by the antenna current and voltage. The influence of azimuthal symmetry are shown by the electromagnetic simulation and the measurement result of plasma density. The radial uniformity can be controlled by locating the concentric antennas which have different diameters. The power distribution ratio and its control method are presented in the case of parallel antenna connections.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.1
• /
• pp.85-91
• /
• 2009

This paper proposes a simulation method of the internal winding fault to calculate the short-circuit current, electromagnetic force and vibration mode in a distribution power transformer by using FEM program(FLUX2D) and analytic algorithm. A usage of the Transfer matrix method is also presented for the vibration mode analysis of the cable-type winding of power transformer. The equations of the winding are approximated by the series expansions of the distributed mass mode and Timoshenko's beam theory. The simulation examples are provided for the cable type winding of the transformer(22.9[kV]/220[V], 1,000[kVA]) to verify the method. The proposed Transfer Matrix Method is also verified by the ANSYS program for the vibration mode of the transformer winding. The method presented may serve as one of the useful tools in the electromagnetic force and vibration analysis of the transformer winding under the short circuit condition.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.9
• /
• pp.613-620
• /
• 2016

In order to scrutinize the fluid conductivity effects on the electromagnetic flowmeter(EMF) characteristics, a small scale EMF was designed and fabricated. The measuring tube has a $3mm{\times}4mm$ rectangular cross-section, 9 mm length, and a $2mm{\times}3mm$ plate electrode and a ${\Phi}1.5mm$ point electrode. The design parameters, such as the magnetizing frequency and the number of coil turns, and the diameter were optimized. The EMF was tested with a gravimetric calibrator and showed good linearity in the range of 0 to $1.17{\times}10^{-5}m^3/s$. The fluid conductivity was varied between 3 and $11{\mu}S/cm$, and the magnitude of the flow signal was proportional to the fluid conductivity and the wetted area of the electrode. The design information and the test results provide flow measurement techniques for very low flowrate.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.2
• /
• pp.70-74
• /
• 2015

In this paper, two-dimensional resonant transmitter and receiver for WPT is designed and implemented using method that use $90^{\circ}$ phase shifted input power to orthogonal transmitter. Mutual inductance is minimized by using proposed each orthogonal coil of receiver and the method that inputs $90^{\circ}$ phase shifted power is used to radiate magnetic energy into two dimension. This method facilitates two dimensional resonant WPT by solving power efficiency degradation problem according to location in general WPT. The resonance frequency is 6.78 MHz and the distance between transmitting and receiving resonator is 200 mm. The transfer efficiency of the proposed wireless power transfer system is higher than 40 % at all direction.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.29 no.1
• /
• pp.133-139
• /
• 2005

Resonant-Type Magnetometer(RM) using high permeability isotropic magnetic material is designed to implement Smart Digital Compass. Theoretically, the inductance L of a coil, winding on the magnetic core, is proportion to the change of permeability $\mu(H)$ and, the change values of L can be obtain as the change of frequency by simple Schmitt Trigger circuit. By the use of integrated circuit switch, the RM can be designed with simple circuit and it can provide overcoming the drift by temperature and the variation of operating points in $\mu(H)$ curve. The facts that Metglas 2705M is an optimum magnetic material and ship's permanent magnetism can be obtain from measured values of RM are also known in this study.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.10
• /
• pp.995-999
• /
• 2015

Inductive sensors are versatile and economical devices that are widely used to measure a wide variety of physical variables, such as displacement, force, and pressure. In this paper, we propose a simple inductive sensor consisting of a thin partial ring and a coil set. The self-inductance of the sensor was estimated using magnetic circuit analysis and validated through finite element analysis (FEA). The natural frequency of the ring was estimated using Castigliano's theorem and the method of equivalent mass. The estimation was validated through experiments and FEA. A prototype sensor with a signal processing circuit is built and applied to noninvasively sense the pressure inside a flexible tube. The obtained sensor outputs show quadratic behavior with respect to the pressure. When fitted to a quadratic equation, the least-square measurement error was less than 2%. The results confirm the feasibility of pressure sensing using the proposed inductive sensor.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.17 no.3
• /
• pp.156-161
• /
• 1997

The eddy current probe was designed for the test of fin tubes that have uneven outer and inner surfaces to enhance the efficiency of heat emission. Because of the surface roughness of the fin tube, it needs much care to detect flaws in the tube employing eddy current test(ECT). We made ECT probes with different coil lengths and performed eddy current test using these probes for artificially flawed specimens. By the fast Fourier transform and digital filtering, signals from these probes were processed to characterize frequency spectra. From the analysis of eddy current signals and their frequency spectra, we concluded that, for the effective testing of the tubes with the fins of 1mm pitch, 4mm coil length gave the highest S/N ratio.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.10
• /
• pp.57-62
• /
• 2009

This study proposes the optimization and numerical analysis of the antenna circuit for antenna design with 13.56 MHz as transmitting wireless power, for calculating the dose radiation exposure to the real time. The 13.56 MHz of the antenna frequency bands is used to the loop antenna which is a induced current for transmitting the power with wireless the reader to the tag. The study compared to the real measurement value as calculating the value of the inductance and capacitance through the numerical analysis for the antenna LC resonance using the theory of the electromagnetic induction method. We tried to search for the resonance point as the voltages of both sides of antenna coil by the scope measures of the peak point, as we tried to be variable the resonance capacitor for the optimization tuning of the antenna circuit and the matching of the antenna port. We convince our research contributes to help the design and application technology of the wireless power transmit system which is received power supply with wireless.

• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.761-765
• /
• 1995

The old Timing Controller for Control Element Drive Mechanism (CEDM) is designed as an open loop control system because it is difficult to mount sensors within the Control Element Drive Mechanism(CEDM) which is operating under the pressure boundary of the reactor vessel. In this work new method which can be used to detect the CEDM operational conditions without mounting sensors within the CEDM housing is developed in order to resolve problems of the old Timing Controller. By using the developed new method, the new Timing Controller for the CEDM is designed as a closed loop controller which has features of the control rod drop prevention, fine position control and the coil life time extension. The algorithm developed under closed loop control concept resolves most problems occurred in the old Timing Controller and improves the performance and reliability of the system. During designing and testing of the Timing Controller algorithm, the real time CEDM simulator developed here was used. And all functions of the developed algorithm were verified using CEDM simulator with the real data collected from the site. The results show that the Timing Controller performs its intended functions properly.