• Journal of the Korean Geosynthetics Society
• /
• v.18 no.4
• /
• pp.115-127
• /
• 2019

The low-flow grouting injection technique, the target construction method for this study, is a method of pouring mortar into the ground by non-emission replacement principle, which can be expected to increase the density of the ground, and, in some cases, be used as a base file using the strength of the high injection solids, along with low noise, low pollution, and high durability. To verify that the dynamic characteristics of the ground are improved by the low-flow injection technique, the test work was conducted on the site and physical tests were performed, and the quality of the improvement formed in the ground was verified through the indoor test on the core and core recovery rate was analyzed. The density logs test layer calculated the volume density of the ground layer by using the Compton scattering of gamma-rays, and the sonic logs was tested on the ground around the drill hole using a detector consisting of sonar and receiver devices inside the drill hole. As a result of the measurement of the change in physical properties (density and sonic logs) before and after grouting, both properties were basically increased after infusion of grout agent. However, the variation in density increase was greater than the increase in speed after grouting, and the ground density measurement method was thought to be effective in measuring the fill effect of the filler. Strength and core recovery rates were measured from specimens taken after the age of 28 days, and the results of the test results of the diffusion and strength test of the improved products were verified to satisfy the design criteria, thereby satisfying the seismic performance reinforcement.

• Tunnel and Underground Space
• /
• v.13 no.1
• /
• pp.33-43
• /
• 2003

Field investigations of the orientations of discontinuity planes inside the borehole for designing the underground rock structures have been depend solely on the borehole image-taking techniques. But, borehole image-taking has to be processed after the completion of drilling operation and also requires the handling of highly expensive apparatus so that practical application is very restricted. In this study Discontinuity Orientation Measurement (DOM) drilling system and discontinuity analysis model RoSA-DOM are developed to acquire the reliable information of rock structure by analyzing the characteristics of joint distribution. DOM drilling system retrieves the rock core on which the reference line of pre-fixed drilling orientation is engraved. Coordinates of three arbitrary points on the joint surface relative to the position of reference line are assessed to determine the orientation of joint plane. The position of joint plane is also allocated by calculating the location of core axis at which joint plane is intersected. Then, the formation of joint set is analyzed by utilizing the clustering algorithm. Total and set spacings are calculated by considering the borehole axis as the scanline. Engineering applicability of in-situ rock mass around the borehole is also estimated by calculating the total and regional RQDs along the borehole axis.

• The Journal of Engineering Geology
• /
• v.23 no.4
• /
• pp.329-340
• /
• 2013

A geologic survey of the Bukpyeong and Pohang basins, as candidate basins for the geological storage of $CO_2$, was performed to evaluate storage capacity and security. To analyze the mechanical stability of the storage reservoir and cap rocks, we measured the porosity, seismic velocity, uniaxial strength, internal frictional angle, and Young's modulus of core samples recovered from the two basins. It is costly and sometimes impossible to conduct tests over the entire range of drill holes, and continuous logging data do not yield the mechanical parameters directly. In this study, to derive the mechanical properties of geologic formations from the geophysical logging data, we determined the empirical relations between the physical properties (seismic velocity, porosity, and dynamic modulus) and the mechanical properties (uniaxial strength, internal friction angle) of the core samples. From the comparison with our core test data, the best fits to the two basins were selected from the relations suggested in previous studies. The relations between uniaxial strength, Young's modulus, and porosity of samples from the Bukpyeong and Pohang basins are more consistent with certain rock types than with the locality of the basins. The relations between the physical and mechanical properties were used to estimate the mechanical rock properties of geologic formations from seismic logging data. We expect that the mechanical properties could also be used as input data for a modeling study to understand the mechanical instability of rock formations prior to $CO_2$ injection.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.4 no.4
• /
• pp.390-399
• /
• 1999

Siliceous and calcareous deep-sea core sediments were collected by a multiple corer from the KODOS (Korea Deep Ocean Study) area, northeast equatorial Pacific, to compare vane shear strengths measured by two different apparatuses and in different places of on-board and on-land laboratories. The apparatuses were 1) a hand-held vane with four blades of $2.0{\times}2.0$ cm, and 2) a motorized shear vane system with four blades of $1.0{\times}0.88$ attached on a rotational viscometer. Depth profiles of shear strengths of core samples determined by the apparatuses do not show any consistent difference. Also, there is no consistent difference between shear strength values measured on-board and on-land laboratories after storing the core samples for three months in a cold room by a motorized shear vane system. However, there are considerable differences between depth profiles of shear strengths measured at four different points (holes) of a core sample. Moreover, significant differences among the profiles of different tube samples from a multiple corer within a sampling station were observed. Heterogeneity in physical properties of each depth and sediment column, possibly due to bioturbation and bottom current flows, is likely responsible for the differences in the geotechnical properties.

• Journal of the Korean Institute of Gas
• /
• v.26 no.2
• /
• pp.1-8
• /
• 2022

The purpose of this study is to prepare GPTMS((3-Glycidoxypropyl) trimethoxysilane)-SiO₂ nanofluid and analyze the effect of nanofluid injection on carbonate reservoirs. Structural analysis of silica nanoparticles modified by GPTMS was investigated by FTIR(Fourier transform infrared spectroscopy). C-H stretching vibrations at 2,950 cm^-1 indicating the silica surface modification with GPTMS were observed when the silane feed was over 0.5 mmol/g. Also, the coreflooding test by nanofluid injection on the aged limestone and dolomite plug samples was carried out with different particle concentration and flow rate. The incremental oil recovery was up to 18.9%, and contact angle and permeability of carbonate samples were changed by the effect of nanoparticle adsorption on pore which caused wettability alteration and pore size change. Therefore, the prepared nanofluid will be utilized as an injection fluid for enhancing oil recovery and modifying fluid flow properties such as change of rock wettability and permeability in carbonate reservoirs.

• Journal of Energy Engineering
• /
• v.21 no.1
• /
• pp.55-67
• /
• 2012

For the development of gas hydrate as new future energy resources, the drilling was carried out at the five locations where have high potential as gas hydrate bearing sediments in Ulleung basin, offshore Korea in 2007. Well log data were obtained from all wells and core data were procured from 3 wells, UBGH1-04, UBGH1-09 and UBGH1-10. In this study, user-friendly software, "KMU GH Logs 2010", is developed and this software is based on the estimation methods developed in previous study for gas hydrate bearing sediments and the properties estimated from UBGH1-04, UBGH1-09 and UBGH1-10. Petrophysical properties in un-cored wells, UBGH1-01 and UBGH1-14, are also estimated by using well log data. Porosity is estimated by density log and gas hydrate saturation is calculated by sonic log and resistivity log. Sedimentary facies are estimated by applying the linear discriminant analysis using both well log and sedimentary facies data from core analysis. It is confirmed that DITM facies and MSS facies appeared signs of gas hydrate disassociation are able to be distinguished by the method.

• The Journal of Engineering Geology
• /
• v.24 no.3
• /
• pp.423-429
• /
• 2014

Development of a reservoir pressure core sampler (PCS) with a built-in data logging system (DLS) for recording real-time temperature and pressure observations is critical in domestic hydrocarbon production to accurately measure and monitor reserves of shale gas, coalbed methane, and gas-hydrate. Another purpose of this new technology is to minimize the loss of gas from the core as the drill core is collected. This is accomplished by maintaining the pressure of the sample from the moment the drill core is obtained at depth, thus allowing an accurate analysis of shale gas, coalbed methane gas, and gashydrate within the core. Currently, the United States and European countries have monopolized the development and marketability of PCS technologies. We are thus developing a reservoir PCS by analyzing the operating principle and mechanisms of the existing PCS, and by conducting tests on the existing PCS. We further aim to develop a PCS with a maximum operating pressure of 100 bar, a maximum operating temperature of $-20^{\circ}C$ to $40^{\circ}C$, and a pressure loss rate of 10%.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.147.1-147.1
• /
• 2011

지식경제부 가스 하이드레이트 개발사업의 일환으로 동해 울릉분지 가스 하이드레이트 2차 시추(Ulleung Basin Gas Hydrate Drilling Expedition: UBGH2)가 2010년 7월 8일부터 9월 30일까지 D/V Fugro Synergy를 이용하여 수행되었다. UBGH2 수행을 위해 선정된 13개 site에서 약 1개월 동안 Schlumberger사의 장비를 이용 Logging-While-Drilling/Measurement-While-Drilling(LWD/MWD) 자료를 취득하였다. LWD/MWD 자료는 선상에서 분석되었으며, 이 결과는 coring 및 borehole plan 수립을 위하여 활용되었다. Coring Phase 동안 10개 site의 18개 hole로부터 퇴적물 코어 시료를 채취하고 선상에서 퇴적학, 지구화학, 생지화학, 물리적 특성 등 각종 분석과 측정 작업을 수행하였다. 약 2개월에 걸쳐 수행된 coring phase 동안에 2개 site에서 FAOL(Fugro Alluvial Offshore Limited)사의 장비를 이용 Wireline Logging/Vertical Seismic Profile(WL/VSP) 자료도 취득하였다. LWD/MWD phase와 coring phase 동안 12개 site에서 무인잠수정(remotely operated vehicle: ROV)를 이용하여 퇴적물 시료 채취, 해저면 관찰, 용존메탄 측정 등의 작업을 수행하였으며, 선상에서 취득된 이들 자료를 분석하였다. Coring을 수행한 모든 site에서 가스 하이드레이트 부존을 확인하였으며, 다양한 산상의 가스 하이드레이트 실물을 회수하고 분석하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.2
• /
• pp.455-460
• /
• 2010

The high-efficiency induction motor reduces the generation loss of conventional induction motors and saves energy with less electricity consumed, enabling the return of initial facilities investments on a shorter-term basis due to its low operation cost and allowing the extension of the life of the motor. Poscore has entered the phase of development of high-efficiency induction motor based on its experiences to date in cooperation with electricity researchers. This paper examines the development of the small motor die for the high-efficiency induction motor.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.650-654
• /
• 2003

A major problem of nuclear energy is the production of radioactive wastes. Needs for more environmentally favorable method to decontaminate radioactive contaminants make the use of liqui $d^ercritical $CO_2$ as a solvent medium. In removing radioactive metallic contaminants under $CO_2$ solvent, two methods - use of chelating ligands and that of water in $CO_2$ emulsion-are possible. In the chelating ligand method, a combination of ligands that can make synergistic effects seems important. We discuss about the properties of microemulsion formed by F-AOT and that by non-ionic surfactant. By adding acid in water core, decontamination of metallic parts, soils were possible. The rate of metal surface dissolution to the microemulsion solution was measured by QCM. The possibility of recovering the surfactants after use is also mentioned.ed.