• Resources Recycling
• /
• v.29 no.5
• /
• pp.55-63
• /
• 2020

In order to investigate the separation of Co(II) and Ni(II) by ionic liquids from weak hydrochloric acid solutions, extraction experiments were performed by changing the type and concentration of ionic liquids and the initial pH of the aqueous phase. Two kinds of ionic liquids based on Aliquat 336 were employed in this work; one was synthesized by reacting organophosphorus acids(D2EHPA, PC88A, Cyanex 272, Cyanex 301) with Aliquat 336 and the other was prepared by exchanging the chloride ion of Aliquat 336 with SCN^-. The three types of ionic liquids (ALi-D2, ALi-PC, and ALi-CY272) showed better extraction of Co(II) than Ni(II), and the equilibrium pH was higher than the initial pH. In the case of ALi-CY301, the selectivity of Co(II) and Ni(II) depended on the extraction conditions. In addition, the effect of the addition of TBP to the ionic liquid on the extraction of two metals was also investigated. Employment of ALi-SCN as an extractant resulted in selective extraction of Co(II) and complete separation of the two metal ions was possible.

• Resources Recycling
• /
• v.19 no.4
• /
• pp.29-34
• /
• 2010

Distribution diagram of $CoCl_2$ and $MnCl_2$ was obtained by analyzing ionic equilibria of the two metals in HCl solution. In the HCl concentration range of 4 and 10 M, most of cobalt exists as $CoCl_2$, whereas Mn exists $MnCl_{3}^-$ and $MnCl_2$. Extraction isotherm of Co(II) and Mn(II) was calculated by using the equilibrium constant for the solvent extraction of the two metals by Alamine336. Although the equilibrium constant for the solvent extraction of Mn was higher than that of Co, extraction isotherm indicated that cobalt could be extracted more efficiently than manganese at the same initial extraction conditions.

• Resources Recycling
• /
• v.31 no.3
• /
• pp.73-80
• /
• 2022

Reduction smelting of spent lithium-ion batteries at high temperature produces metallic alloys. Following solvent extraction of the leaching solutions of these metallic alloys with either sulfuric or hydrochloric acid, the raffinate is found to contain Ni(II), Co(II), Mn(II), and Si(IV). In this study, two cationic exchange resins (Diphonix and P204) were employed to investigate the loading behavior of these ions from synthetic sulfate and chloride solutions. Experimental results showed that Ni(II), Co(II), and Mn(II) could be selectively loaded onto the Diphonix resin from a sulfate solution of pH 3.0. With a chloride solution of pH 6.0, Mn(II) was selectively loaded onto the P204 resin, leaving Ni(II) and Si(IV) in the effluent. Elution experiments with H₂SO₄ and/or HCl resulted in the complete recovery of metal ions from the loaded resin.

• Resources Recycling
• /
• v.31 no.1
• /
• pp.21-28
• /
• 2022

The smelting reduction of spent lithium-ion batteries results in metallic alloys of cobalt, nickel, and copper. To develop a process to separate the metallic alloys, leaching of the metallic mixtures of these three metals with H₂SO₄ solution containing 3% H₂O₂ dissolved all the cobalt and nickel, together with 9.6% of the copper. Cyanex 301 selectively extracted Cu(II) from the leaching solution, and copper ions were completely stripped with 30% aqua regia. Selective extraction of Co(II) from a Cu(II)-free raffinate was possible using the ionic liquid ALi-SCN. Three-stage cross-current stripping of the loaded ALi-SCN by a 15% NH₃ solution resulted in the complete stripping of Co(II). A process was proposed to separate the three metal ions from the sulfuric acid leaching solutions of metallic mixtures by employing solvent extraction.

• Journal of the Mineralogical Society of Korea
• /
• v.23 no.3
• /
• pp.183-189
• /
• 2010

It is of importance to separate Ni(II) and Co(II) from Mg(II) in solution which was leached from nickel laterite ore. In order to investigate the possibility of separating Ni(II) and Co(II) from Mg(II), adsorption behavior of the three metals from individual and mixed sulfate solutions was investigated by using Diphonix resin. The concentration of each metal in solution was fixed at 100 ppm and the pH of the sulfuric acid solution was changed from 5 to 7. At ambient temperature, the adsorption behavior of the three metal ions followed Langmuir adsorption isotherm. The loading capacity of Diphonix resin for the three metal ions was obtained from the Langmuir isotherm. Since adsorption behavior of the three metal ions from the mixed solution was similar to each other, it was found to be difficult to separate Ni(II) and Co(II) from Mg(II) by using Diphonix resin.

• Journal of the Korean Chemical Society
• /
• v.31 no.3
• /
• pp.231-235
• /
• 1987

In 10M chloride (4M HCl + 6M LiCl) solution, cobalt, but not nickel, formed complex anion (${CoCl_3}^-$), and this anion was extracted by a liquid anion exchanger with Amberlite LA-2. The ion exchange capacity was 2.175meq of cobalt complex per unit ml of Amberlite LA-2. Upon eluting the resin with 0.4M nitric acid, the cobalt complex was stripped and transfered into eluate quantitatively. By using this separation method in the chloride solution dissolved with 50mg of cobalt (II) and 500mg of nikel(II), recovery of cobalt were 99.6 percent.

• Resources Recycling
• /
• v.29 no.5
• /
• pp.73-80
• /
• 2020

In order to develop a process for the recovery of valuable metals from spent LiBs, solvent extraction experiments were performed to separate Cu(II) and/or Co(II) from synthetic hydrochloric acid solutions containing Li(I), Mn(II), and Ni(II). Commercial amines (Alamine 336 and Aliquat 336) were employed and the extraction behavior of the metals was investigated as a function of the concentration of HCl and extractants. The results indicate that HCl concentration affected remarkably the extraction efficiency of the metals. Only Cu(II) was selectively at 1 M HCl concentration, while both Co(II) and Cu(II) was extracted by the amines when HCl concentration was higher than 5 M, leaving the other metal ions in the raffinate. Therefore, it was possible to selectively extract either Cu(II) or Co(II)/Cu(II) by adjusting the HCl concentration.

• Journal of the Korean Chemical Society
• /
• v.47 no.6
• /
• pp.547-552
• /
• 2003

Separation and determinations of Co(II) and Ni(II) ions as their 4-(2-pyridylazo)resorcinol(PAR) chelates by reversed-phase capillary high-performance liquid chromatography(RP-CpHPLC) were performed. Among many capillary columns, Vydac C4 column was selected and acetonitrile solution was used as mobile phase. The effect of pH and MeCN concentration(%) on the retention factor, k and peak intensity was examined and discussed. As a results, it was found that 22.5% MeCN and pH 5.60 was adequate as mobile phase for the separation of the two metal ions and determination of Co(II) ion, but the mobile phase condition for Ni(II) ion determination was 22.5% MeCN of pH 7.20. Detection limit(D.L., S/N=3) of Co(II) and Ni(II) ions were $2.0{\times}10{-7}$ M(14.9 ppb) and $1.0{\times}10{-6}$ M(59.2 ppb), respectively.

• Journal of the Korean Chemical Society
• /
• v.51 no.4
• /
• pp.331-338
• /
• 2007

A rapid, simple and sensitive spectrophotometric method was developed for the determination of cobalt(II) using 2-hydroxy-3-methoxy benzaldehyde thiosemicarbazone (HMBATSC) as a analytical reagent. The metal ion in aqueous medium forms a brown coloured complex with HMBATSC at pH 6.0. The complex has two absorption maxima at 375 nm and 390 nm. At 375 nm, the reagent shows considerable absorbance, while at 390 nm the reagent does not shows appreciable absorbance. Hence, analytical studies were carried out at 390 nm. Beer's law is obeyed in the range of 0.059-2.357 μg ml-1 of Co(II). The molar absorptivity and Sandall's sensitivity of the method are 2.74×104 l mol-1 cm-1 and 0.0024 μg cm-2 respectively. The interference of various diverse ions has been studied. The complex has 1:2 [Co(II)- HMBATSC] stoichiometry. A method for the determination of cobalt(II) by second order derivative spectrophotometry has also been proposed. The proposed methods were applied for the determination of cobalt(II) in alloy steels, vitamin B12 and in some biological samples.

• Analytical Science and Technology
• /
• v.6 no.1
• /
• pp.57-63
• /
• 1993

Spectrophotometric determination of cobalt by flow injection method is described. 2-(5-Bromo-2-pyridylazo)-5-(N-propyl-N-sulfopropylamino) aniline rapidly forms a water-soluble complex with cobalt in $NH_3-NH_4Cl$ buffer solution at pH 10.5. The absorption maxima of this complex is at 545 nm with molar absorptivity of $58000L\;mol^{-1}\;cm^{-1}$. The calibration curve of cobalt is linear over the range of 0.1 to 0.6ppm and the detection limit is 25ppb. The relative standard deviation is ${\pm}0.72%$ for 0.5ppm and the sampling rate is $60samples\;hr^{-1}$. The interfering effect of some cations and anions was investigated. Ni(II), Cu(II), Fe(III) and $CN^-$ interfered severely. The interfering effect of these matallic ions could be decreased by adding $1.0{\times}10^{-3}M$ EDTA solution to the carrier stream.