• Transactions of Materials Processing
• /
• v.21 no.6
• /
• pp.360-365
• /
• 2012

The aim of this study was to investigate the effects of forming depth on the deformation behavior of cup-like tubes made of AISI1020 steel in tube spinning process. Spinning process was performed on cup-like tubes, which had an inner diameter of 34mm and thicknesses of 7, 8.5 or 11.5mm. The forming depths achieved were 3, 4, and 5.5mm. The complex deformation behaviors occurring during the tube spinning process was explained using the experimental results. Also analyzed were the causes of the material buildup and the bulge defect of inner surface, observed on cross section of tubes. The relationship between tube spinning conditions and the height of bulge defect was examined. The results indicate that bulge defect is increased with a decrease of the forming depth. Moreover, a critical forming depth exists for preventing the generation of the bulge defect in the tube spinning process. The present results will be useful for future decisions of forming depths for successful tube spinning of cup-like tubes.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2004.05b
• /
• pp.1086-1091
• /
• 2004

일반적으로 하천유량은 하천단면에서 하폭, 수심, 유속 등에 대한 연속적인 측정으로 계산된다. 이론적인 적분법 대신 구간 유량의 합으로 유량을 산정하는 방법들은 한 측선에서 유속과 수심이 균일하다는 가정과 측선사이에서 유속 및 수심이 선형적인 관계를 지니고 있다는 가정을 포함한다. 따라서 너무 작은 측선수의 선택은 상당한 오차를 유발하게 된다. 유속-면적법에 의한 하천유량 측정에 있어 한정된 측선수를 선택하는데 따른 측정유량의 불확실도를 분석하였다. 측선수에 따른 불확실도를 분석하기 위해 국내의 중소하천 유량측정 지점을 중심으로 9개 하천에서 19개의 측정자료를 활용하였다. 유속 및 수심측정은 50개 이상의 측선에서 측정하였으며, 한 측점에서 유속측정은 수직축 컵형태의 유속계를 활용하여 120초 이상 측정하였다. 50개 이상의 측선으로 계산한 유량을 진유량으로 가정하고 각자 측선수에 따른 불확실도를 분석한 결과 작은 측선수를 선택할 경우 정확도가 심자하게 낮아짙 가능성이 있는 것으로 나타났다. 또한 20측선 이상에서 $5\%$이하로 수렴되어가는 경향을 나타냈다. 따라서 하천 유량측정 실무에서 20측선 이상의 측선을 선택하는 것이 비교적 정확하면서 경제적인 유량측정이 될 것으로 판단된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.249-249
• /
• 2011

전력용 개폐장치인 진공차단기의 차단부가 송배전 시스템에 30 [kA] 정도의 커다란 사고전류가 흐르는 것을 방지하기 위하여 동작될 때 차단부 내부 전극 사이에 25,000 [K] 이상의 아크 플라즈마가 발생하게 된다. 두 전극 사이에 발생된 아크 플라즈마는 약 10 ms~20 ms 동안 지속되다가 교류전원의 전류영점 부근에서 회복된 절연성능으로 인하여 자연스럽게 소멸되지만, 대전류 구간동안 아크 플라즈마의 집중 현상 등에 의하여 전극의 심각한 손상 등이 발생되면 절연성능이 요구된 만큼 회복되지 못하여 사고전류를 차단하지 못하며 시스템에 연결된 기기들에게 심각한 손상을 입히고 정전사고를 일으킨다. 본 연구에서는 전자계-열유동 연성해석기법을 이용한 축자계 진공차단부에서 발생하는 아크 플라즈마의 3차원 수치해석을 통하여 전극의 심각한 손상을 입히는 아크플라즈마의 집중 현상에 관한 축자계의 영향을 고찰하고자 한다. 수치해석을 위한 아크 영역은 양극과 음극의 직경과 같은 직경의 원기둥으로 가정하였고, 전자계 해석으로부터 얻어진 로렌츠 힘과 줄열을 열유동 해석을 위한 Navier-Stokes 방정식의 파라미터로 입력하여 해석을 수행함으로써 전자계와 유체역학적인 영역을 동시에 연계한 순차적 일방향 연성해석 기법을 적용하였다. 컵형 축자계 진공차단부 내 아크영역에서의 로렌츠 힘의 특성과 온도분포에 대하여 수치해석을 수행하였고, 크기가 다른 두 로렌츠 힘에 의하여 양극표면으로 집중되는 온도분포의 크기를 비교함으로써 진공아크 플라즈마의 집중현상에 영향을 미치는 주요 요소를 규명할 수 있었다.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.12
• /
• pp.82-87
• /
• 2001

This paper deals with mirror grinding of a small-sized aspherical lens by the resin bonded diamond spherical wheel. Up to now, a spherical lens has been used for the lens of the optical communication optical part. However, recently, the aspherical optical parts are mainly used in order to attempt the improvement in image quality and miniaturization of the optical device. It is possible to manufacture the aspherical lens which is presently being used in optical instrument through ultra-precision machinery technology. Also, to realize compactability, efforts are being made to produce a micro aspherical lens, for which the development of a high-precision, micro molding die is inevitable. Therefore, extensive research is being done on methods of producing an micro aspherical surface by high-precision grinding. In this paper, the spherical wheel was trued by cup-type truer and tool path was calculated by the radius of curvature of wheel after truing and dressing. And then in the aspherical grinding experiment, WC material which is used as a molding die for the small-sized aspherical lens was ground. It results was that a form accuracy of 0.1918${\mu}m$ P-V and a surface roughness of 0.064${\mu}m$ Rmax.

• KOMUNHWA
• /
• no.56
• /
• pp.93-146
• /
• 2000

Categories of pottery found in southern west parts of Korea are such as, Mounted Cup, Jar, Long necked jar, Pottry stands, Cups with handle and the like. It is believed to date from mid-5c that distinctive production of pottery and its distribution by whi

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.3
• /
• pp.325-331
• /
• 2010

Three-cup anemometers are popular devices for measuring wind speeds in automated weather stations, environmental monitoring systems, and wind turbines. Cup anemometers usually suffer from lack of long-term stability owing to the wear of the bearing systems that support the rotational parts. The bearing systems are susceptible to external pollutants, vibrations, and gusts. Therefore, these anemometers have to be calibrated regularly to maintain the desired characteristics for measuring wind speed. In the present study, a new in-situ calibration system to help reduce cost and save time by calibrating the cup anemometers at the installation site is proposed. A portable in-situ calibrator was fabricated. After the characteristics of this calibrator were verified, it was used to calibrate cup anemometers. Some of the calibration results were compared with the data obtained by wind tunnel testing.

• Composites Research
• /
• v.13 no.1
• /
• pp.1-10
• /
• 2000

During the compression molding process of the continuous fiber-reinforced polymeric composites, two main problems such as fiber-matrix separation and fiber orientation are produced by the difference of flow velocity. Molded parts are lead to be nonhomogeneous and anisotropic. As the mechanical property of the products are dependent on the separation and orientation, it is important to research the fiber mat structure and molding condition. If the fiber mat structure is changed by the increment of needling, the separation decreases and after compression molding the orientation is easily aligned. As it were, the compression moldability is good. But the defects as tears, thin thickness are produced in the products. Therefore, it is important to clarify the moldability in relation to the usage of products and the expenses of produce on the actual process. Therefore we must make the measurement methods that can define the moldability of products. In this research, the effects of the fiber mat structure(NP = 0, 5, 10, 25, 50 punches/$cm^2$) and the mold geometry($r_p$ = 1, 25, 50 mm) on the moldability of products were discussed. We investigated the case of one-dimensional flow in order to obtain the degree of nonhomogeneity and the fiber orientation function. In result, we could gain the correlation coefficient of the continuous fiber-reinforced polymeric composites. Also we experimented on the cup-type compression molding which was appeared the wrinkle on the flange part by the complex stress condition in order to gain the degree of nonhomogeneity and area ratio. In result, the moldability of products was expressed as the correlation coefficient and area ratio.

• Horticultural Science & Technology
• /
• v.32 no.4
• /
• pp.571-575
• /
• 2014

'Dream Song' is a cultivar of Gypsophila paniculata developed by the Jeollabuk-do Agricultural Research & Extension Services in 2010 for cut-flower production. This hybrid was bred from 121 seedlings collected from an open-pollinated population of 'Gyp06-11'. It has novel morphological characteristics of upright plant type, lanceolate leaves, double florets with a few bright white-colored petals of obovate shape, truncate petal tips, and cup-shaped calyces. Furthermore 'Dream Song' has desirable cultivation characteristics including narrow branching angle, and moderate resistance to powdery mildew, thrips and leaf miners. Moreover it produces more primary branches, and longer internodes and flower stalks than reference cultivar 'Bristol Fairy' during summer cultivation in a subalpine area (500 m over the sea level). Flowering in 'Dream Song' is delayed by about 17 days as compared to 'Bristol Fairy'. 'Dream Song' produces normal flowers with 2 pistils and an average of 10.4 stamens, with fewer malformed flowers than 'Bristol Fairy'.

• Composites Research
• /
• v.12 no.5
• /
• pp.31-39
• /
• 1999

Glass-fiber reinforced polymeric composites provide the desitable properties of high stiffness and strength as well as specific weight. Hence, they have become some of the most important materials in several industries. These composites can be grouped into thermoplastic and thermoset composites, with thermoplastic composites having several advantages over thermoset composites in mechanical properties and processing. As a result, the study of the material behavior and forming techniques of such composites has attracted considerable attention in recent years. When the continuous fiber-reinforced polymeric composites are molded by flow molding, the molded parts leads to be nonhomogeneity and anisotropic because of the separation and orientation of fibers. As the characteristics of the products are greatly dependent on the separation, it is very important to clarify the separation in relarion to molding conditions, fiber mat structures and mold geometry. In this study, the effects of the mold geometry and the fiber mat structure on the compression moldability are studied using the cup-type molding.

• Conservation Science in Museum
• /
• v.7
• /
• pp.53-62
• /
• 2006

The wooden armor frame and various lacquerware artifacts excavated from the low swamp remains in Imdang, Gyeongsan have very weak material and lacquer coating; in case they are exposed in the air, they are likely to be shrunken and deformed immediately. The wooden armor frame has large size and it might be dissolved during freeze-drying. The lacquer coating of lacquerware blocks the penetration of chemicals and it is very likely to swell or peel off during the treatment. Therefore, to prevent the dissolution during vacuum freeze-drying, the wooden armor frame was replaced with t-butanol and impregnated in t-butanol solution with PEG#3, 350 43%, and lacquerware was impregnated in PEG#3, 350 40% solution at room temperature and freeze-dried. According to the analysis of the lacquer fragment from the lacquerware, the lid and the mounted cup was pasted with the mixture of lacquer and black pigment (soot) on the base layer after the first coating and pasted two or three times more with natural lacquer; the red lacquered wooden cup was pasted with the mixture of lacquer and black pigment on the base layer and pasted once on the middle layer. The top lacquer (red) was pasted with the mixture of iron oxide(Fe₂O₃).