• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.12
• /
• pp.686-693
• /
• 2018

Various types of re-bar splicing methods have been developed and applied to reinforced concrete (RC) structures in the field. According to previous studies, the coupler splice is relatively superior to the lap splice in terms of cost efficiency when the diameter or strength of the re-bar is larger or higher. This study was performed to develop a filler type mechanical splice for a high-strength re-bar (SD600) in reinforced concrete structures. The deformed re-bars were inserted into a circular steel tube coupler and high-strength epoxy filler was then injected into the coupler. The splice system was completed by hardened filler in a coupler. The epoxy filler was used as the manufactured production epoxy to conduct experiments of filler type mechanical splice specimens, and to observe the failure loads and failure aspects of the specimens. For this goal, the experiment of one-way tensile test was conducted for the epoxy filler type mechanical splices specimens according to the compressive strength of epoxy, length of coupler, and diameter of re-bar. The shape of failure of the re-bar coupler splice showed that the re-bars were pulled between the lugs of the re-bars as a result of the shear fracture of the hardened epoxy. The actual failure load of the experiment specimen was approximately 2 times higher than the expected failure load of the epoxy filler, which greatly improves the failure load of the hardening epoxy filler due to the restraint of the steel coupler.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.85-88
• /
• 2016

Two output ports of $90^{\circ}$ hybrid-coupler are generally the same output power with $90^{\circ}$ phase difference. But, Two output ports of $90^{\circ}$ hybrid-coupler must be the different output slope characteristic about frequency because of the different electrical length. In $90^{\circ}$ hybrid-coupler being the same power distribution, 3-dB power distribution at two output ports only exists near the center frequency. And, the output power difference between two output ports increases in accordance with the further away from the center frequency. This paper proposes $90^{\circ}$ hybrid-coupler being the similar output slope characteristic of two output ports in wideband to modify the ${\lambda}/4$ transmission line of $35-{\Omega}$ characteristic impedance between input port and output port near input port. The power difference between two output ports of the proposed circuit is below 0.2dB over 20% bandwidth of the center frequency in ADS(advanced Design System).

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.10
• /
• pp.51-56
• /
• 2000

An all fiber coupler-type add/drop filter has been fabricated by writing a Bragg grating in the coupling region of a fused fiber coupler. The fused fiber coupler with 99.8% coupling ratio and 74/m coupling coefficient was used for the add/drop filter. The add/drop filter shows 99% reflectivity and 83% drop efficiency at the operating wavelength of 1536.2nm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.6
• /
• pp.586-594
• /
• 2013

This paper proposes a new coupling element of microwave slot coupler for designing waveguide slot array which can reduce the effect of undesired higher order mode coupling between coupling and radiating slots in the branch waveguide. The proposed device is composed of a centered longitudinal shunt-series coupling slot at the center of broad wall shared by two crossed rectangular waveguides and an asymmetric compound iris that excites the coupling slot. We first have obtained scattering parameters for the proposed coupler by use of EM S/W tool HFSS and then extracted the parameters of T- network equivalent circuit for the coupling slot. We also have analyzed the resonant properties such as resonant length and normalized admittance by changing the geometrical dimensions. The measured results for the fabricated coupler with short-circuited block ${\lambda}_g/4$ away from the coupling slot are well agreed with the simulated ones.

• Journal of Advanced Navigation Technology
• /
• v.13 no.2
• /
• pp.194-200
• /
• 2009

This paper introduces a ring hybrid coupler using shunt capacitors, high impedance lines and CRLH-TLs (Composite Right/Left-Handed Transmission Lines) with size reduction and bandwidth enhancement. The reduced method of line length uses to combine a short length high impedance line and shunt capacitors. Also, there is combined CRLH meta-material so as to obtain wide bandwidth of transmission line using nonlinear phase characteristic of CRLH-TL that consists of series capacitors and shunt inductors. The implemented ring hybrid coupler shows a novel design with compact size that is smaller than 10% and bandwidth is larger than 60% of conventional ring hybrid coupler.

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.110-111
• /
• 2007

두개의 유니모프 진동자를 이용한 새로운 형상의 마이크로 초음파 리니어 모터를 제안하였다. 유니모프 진동자는 금속판에 판상의 압전소자가 접착되어 있으며, 두개의 유니모프 진동자가 삼각형상의 진동 커플러에 의해 연결되어 스테이터를 구성한다. 스테이터는 두 가지 진동모드(대칭모드와 비 대칭모드)를 가지고 있으며, 이 두 진동모드가 축퇴되도록 설계하였다. 스테이터의 대칭모드와 비 대칭모드를 위상차 $90^{\circ}$로 여진시킴으로써 이동체의 직선(또는 회전) 운동을 발생시킬 수 있다. 시작기 모터는 놀이 0.9 mm, 폭 1 mm, 길이 7.5 mm이며, 구동전압 $100V_{op}$, 구동주파수 300 kHz로 구동되어, 모터 최대속도 0.3 m/s, 최대 추력 6 mN을 달성하였다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.5
• /
• pp.36-41
• /
• 2007

We report the 94 GHz CPW branch-line bandpass filter for planar integrated millimeter-wave circuits. The branch-line coupler operates as a transversal filtering section by connecting the coupling ports to the open load stubs and taking the isolation port as the output node. For design of the 94 GHz branch-line bandpass filter, we built the CPW library and optimized the characteristic impedances and the lengths of the branch-line coupler and the open load stubs. The fabricated 94 GHz bandpass filter exhibits an insertion loss of 2.5 dB with an 11.7 % 3 dB relative bandwidth and the return loss is -18.5 dB at a center frequency of 94 GHz.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1861-1863
• /
• 2001

본 연구에서는 국내에서도 아직 초기단계 기술이라고 할 수 있는 간섭계를 이용한 주요 시설물(변전소등) 안전 감시 혹은 항만 감시 및 방어용 광섬유 격자 그물망 구현을 위한 광섬유 시스템 적용성을 연구한 것이다. 연구에서는 마흐젠더 간섭계의 구성에 비해 구성이 용이한 Sagnac간섭계를 구성 실험하였다. 이 간섭계의 성능 검증을 위하여 1550nm의 중심파장을 방사하는 레이저, 싱글모드 광섬유, 3${\times}$3 커플러 등의 광소자를 사용하였고, 광섬유의 길이의 변화를 주기 위하여 PZT 위상 변조기에 교류 전원을 인가하여 PZT 위상 변조기의 진동을 유도하였다. 또한, 전체 길이 약 180cm, 17${\times}$7, 철봉의 직경 6m의 철망 구조물을 제작후, 센서 부분의 역할을 담당한 광섬유 케이블을 일정한 간격으로 철망 구조물에 케이블 타이로 고정하였다. 철망 구조물에서 발생할 수 있는 각종 외부 가진에 대해, 철망 구조물에 가속도계를 설치하여, Sagnac 간섭계에서의 광 간섭 신호와 가속도계의 신호를 비교 검증 하였다. 본 실험결과를 통하여 광섬유 펜스는 주요 시설물(변전소등) 안전 감시 혹은 항만 감시 및 방어용 경보 시스템에 적합하다고 판단된다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.12
• /
• pp.35-42
• /
• 2004

In this paper, we report Mach Zehnder Interleaver of optical fiber type is fabricated by the fabrication system only for interfermeter design, and it is used $CO_2$ laser to adjust precisely the wavelength. The optical fiber is very sensitive in the thermal variation around. Thus, When fabrication the prototype, it is applied a technique to compensate the optical thermal effect because the center wavelength at the output is shifted according to the thermal variation around. it can he done by applying a substrate with high thermal expansion coefficient as well as an adjusting the position between two optical fiber couplers. Consequently, the output wavelength is shifted within 0.05 nm when the surrounding temperature varies until $60^{\circ}C$.

• Korean Journal of Optics and Photonics
• /
• v.31 no.5
• /
• pp.213-217
• /
• 2020

In this study we report a wet-etching-based fabrication method for adiabatic optical-fiber tapers (OFTs), and describe their adiabaticity and HE₁₁ mode evolution at a wavelength of 1550 nm. The profile of the fabricated system satisfies the adiabaticity properties well, and the far-field pattern from the etched OFT shows that the fundamental HE₁₁ mode is maintained without a higher-order mode coupling throughout the tapers. In addition, the measured far-field pattern agrees well with the simulated result. The proposed adiabatic OFTs can be applied to a number of photonic applications, especially fiber-chip packages. Based on the fabricated adiabatic OFT structures, the optical transmission to the inversely tapered silicon waveguide shows large spatial-dimensional tolerances for 1 dB excess loss of ~60 ㎛ (silicon waveguide angle of 1°) and insertion loss of less than 0.4 dB (silicon waveguide angle of 4°), from the numerical simulation. The proposed adiabatic coupler shows the ultrabroadband coupling efficiency over the O- and C-bands.