• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.1
• /
• pp.90-98
• /
• 2018

Recently, various reinforced concrete joints have been used in reinforced concrete structures. Therefore, it is important to grasp the tensile properties of the spliced rebar. In this study, uniaxial tensile tests were conducted on Grade 60 D22(#7), D29(#9), and two kinds of couplers manufactured according to ASTM A615 standard for evaluating ductility of coupler joints. The strain was measured using an image processing method more accurate and capable of measuring at various points freely. As the result of uniaxial tensile test, it was possible to calculate the stress-strain relationship and the longitudinal strain distribution according to the stress stages and it was founded that the average strain becomes lower as more occupying the coupler joint portions in the same gauge length. In addition, the empirical equations are proposed to account for the effect of the length of the coupler on the ultimate strain and the rupture strain.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.4
• /
• pp.11-19
• /
• 2022

In this study, in order to improve the splice performance of mechanical couplers, two new mechanical couplers with different connection modes were developed with rebar(SD400). The stress analysis of mechanical couplers with two different connection modes was carried out. Uniaxial tensile tests were carried out with type of steel, connection mode and the slope length of internal fastener as variables to analyze the influence on the maximum tensile strength. Building upon this previous work, the specimens that met the code in uniaxial tensile test were fabricated and static loading test and cyclic loading test were performed on the basis of Korean code(KS D 0249). The results of this research are as follows; (1) The tensile strength of steel and the slope length of internal fasteners have a certain influence on the maximum tensile strength. (2) The connection mode has some influence on the stiffness, slip and stiffness reduction rate of the connecting rebars. The results verify the feasibility of the proposed enhanced mechanical coupler in the field.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.6
• /
• pp.22-25
• /
• 2010

This paper presents the modified design that can reject the harmonic signals in the branch-line coupler. After adding open stubs at the center of quarter-wavelength lines of the traditional design, all network parameters can be determined by network equivalence, in order to maintain the conventional function at the operating frequency and suppress its harmonic terms to de chosen. Experimental results show the second and third harmonic suppressions to be -37.5 and -42.7dBs, while maintaining conventional performance at the fundamental frequency.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.3139-3145
• /
• 2014

This paper describes the design of a size-reduced ring hybrid coupler for microwave band using an artificial dielectric substrate(ADS). ADS structure adopts the second substrate on which has lots of the metalized via-holes. The effective capacitance and effective dielectric constant per unit length of ADS increases compared to the normal substrate due to the via-holes. This enables the physical length of microstrip transmission line to be reduced by adopting ADS instead of the normal substrate. In order to present an example of size-reduction of microwave wireless circuit by ADS, a size-reduced 3GHz ring hybrid coupler is designed, fabricated and measured in this work. The designed coupler has the smaller size from the normal one by 65% due to the ADS, while no critical degradation from ideal performances is observed. The measured power division ratio at two output ports are -3.05dB and -3.135dB, respectively. In addition, the phase differences are 3o for in-phase division and 176o for out of phase split. The measured performances are so similar to ideal ones, and prove the design of size-reduced ring hybrid coupler using ADS is successful.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.2
• /
• pp.54-59
• /
• 2013

This letter presents a shorted-stub tapped branch-line coupler for dual-band applications. In the new design, a shorted stub is used to realize 90 phase change at two frequencies. Closed-form design equations are derived to find the characteristic impedance and electrical length of the proposed branch lines using the ABCD-matrix. To verify the design concept, a microstrip coupler operating at 0.8 and 1.85 GHz is fabricated and measured.

• Korean Journal of Optics and Photonics
• /
• v.13 no.5
• /
• pp.373-376
• /
• 2002

An asymmetrical directional coupler with two nonidentical fibers has, for the first time, been proposed and analyzed for an EDFA gain flattening filter (GFF). The characteristics of the transmission spectra of the GFFs have been theoretically investigated for the core spacings, the coupling lengths and the fiber parameters of the asymmetrical directional coupler. The analytical results show that an EDFA gain spectrum with flatness of ~7 ㏈ can be flattened to within $\pm$0.75 ㏈ over a bandwidth of 30 nm by using the asymmetrical directional coupler-based GFF.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.5
• /
• pp.2319-2324
• /
• 2012

In this paper, the design of asymmetric branch line couplers using artificial dielectric substrate (ADS) is described. The effective permittivity and permeability increase in ADS because of the lots of the inserted via-holes. So the physical length and width of transmission lines realized on ADS are reduced compared to the standard lines. This enables one to design size-reduced microwave circuits. As an instance in this work, an asymmetric branch line coupler with the ratio of 3:1 is designed at 2GHz. The designed coupler has a small size of 53.4% compared to the normal circuit while the same performances are preserved. A good agreement between the simulated and measured asymmetric power dividing ratio is shown. The measured loss is only less than 0.2dB, which is a very small value.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.7
• /
• pp.566-569
• /
• 2018

A power line coupler that can apply high-frequency power to a railway overhead line structure was analyzed. It is difficult to supply auxiliary power to an overhead line in a high-voltage environment, and doing so requires a long-distance transfer. A method is proposed that utilizes the resonance on the Rogowski coil, which does not use a magnetic core. A simple overhead line structure was fabricated that consisted of a contact wire, messenger wire, and dropper. Couplers of various sizes were fabricated and deployed on the messenger wire, and the transfer characteristics of the two couplers were compared at a distance. As a result of applying the matching circuit to the coupler, the transmission efficiency was 53% at a distance of 2.5 m. The proposed method shows that it is possible to apply the auxiliary power by using the existing conductor in a special structure, such as the overhead line.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.2
• /
• pp.75-90
• /
• 2015

As soil nails support a ground by the friction between nails and soils being reinforced, the length of soil nails is important factor for a ground stability. Thus, the soil nail length has to be accurately evaluated in order to secure a ground stability. The goal of this study is to suggest the applicability of the non-destructive method as the basic research for the evaluation of the soil nail length. First, the elastic and electromagnetic waves are adopted to select an applicable method for the soil nails connected by the coupler. Test results show that while the ultrasonic waves are not detected due to the coupler, the electromagnetic waves are free for the influence of the coupler. Second, electromagnetic waves are measured for combined soil nails with the length of 1 m~15 m for the investigation of the characteristics of electromagnetic waves. The travel time of the electromagnetic wave increases with an increase in the soil nail length. In addition, the ground cable is used to apply the electromagnetic waves to pre-installed soil nails. Test results show that the travel time of the electromagnetic wave by using the ground cable increases with an increase in soil nail length. This study demonstrates that the electromagnetic wave may be a promising method for the evaluation of the soil nail length.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.228-228
• /
• 2007

전력선 통신용 비접촉식 커플러는 고속형(2~30 MHz)과 저속형(100~450KHz)으로 나누어 볼 수 있는데, 고속형은 현재 국내에서 독자적으로 개발되어 다양한 모델이 적용되고 있는 상황이지만, 저속형은 시작품수준으로 제조되어 있으나 신호전송 특성의 향상절구가 필요한 상황이다. 전력선 통신용 커플러는 전력선 또는 모뎀으로 통신신호를 전달하는 기능을 하는 것으로서, 전력선 통신을 위한 핵심부품이다. 따라서 본 연구에서는 100~450 KHz 대역에서 사용 가능한 저속형 비접촉식 커플러를 제조하기 위해, 권선조건, 대전류형 자심재료의 모의 해석, 노이즈 필터조건, 임피던스 매칭, 하우징방법 등의 각 공정 변수를 확립하고자 하였다. 자심재료의 모의해석에서 자심재료의 높이와 전력선 도체 단면적 변화는 자심재료의 전류포화특성에 영향을 미치지 않으며, 유효길이와 에어-갭 크기가 증가할수록 전류포화특성은 향상되는데, 자심재료의 내경이 64 mm일 때 자심재료의 폭((외경-내경)/2)은 15 mm 이상이어야 하고, 에어-갭은 약 $600\;{\mu}m$ 정도의 에어-갭을 형성시켜야함을 확인할 수 있었다. 또한 저속용 비접촉식 커플러 제조조건 실험에서 내경${\times}$외경${\times}$높이가 $64{\times}94{\times}140mm$인 자심재료를 이용하여 권선 수와 에어-갭을 각각 3회, $400{\sim}600\;{\mu}m$ 삽입했을 때, 가장 우수한 특성을 나타내었다. 그리고 저역 통과 필터를 출력부에 내장하여 통신신호 이외의 노이즈를 제거할 수 있었다. 본 연구에서 제조된 300 A급 지중선용 저속형 비접촉식 커플러는 내경${\times}$외경${\times}$높이가 $58{\times}1144{\times}158mm$이고, 100~450 KHz 통신대역에서 약$7{\pm}2dB$의 삽입손실을 나타내었다.