• Journal of Korean Ophthalmic Optics Society
• /
• v.5 no.2
• /
• pp.65-72
• /
• 2000

The study investigated the effects of base curve radius art the fit of thin, mid-water contact lenses. It was found that central corneal curvature(as measured with the keratometer) was not predictive of the best fitting base curve. Proper lens fit may be the single most important factor that ultimately determines the success of contact lens wear. Comfort, vision, and physiological response are all dependent on the fit of the lens. The percent of optimal fits was highest with the 8.4 mm base curve lens for all three ranges of keratometry values. When fit with the 8.4 mm lens. For most eyes, fitting a flatter lens led to greater decentration, decreased comfort, and no increase in lens movement. The 8.4 mm lens was found to provide on "optimal" fit in over 60% of eyes tested and a fit of "good" or "better" in nearly 90% of eyes tested. Comparisons of different manufactures' lens found that similiar lenses do not always fit in the same way due to subtle design and production differences. Therefore, different products may require different base curve radii to fit the same patient. This is even true when water content, center thickness, and diameter are approximately the same. A praditioner fitting a new patient in this lenses should begin with the 8.4 mm base curve radius.

• Nuclear Engineering and Technology
• /
• v.14 no.1
• /
• pp.1-9
• /
• 1982

Some observations from the examination of actual manhour curves for the power plant design engineering obtained from Sargent & Lundy Engineers and of a few of the model curves proposed by Bechtel, are analyzed in this paper. A model curve representing typical design engineering manhour has been determined as a probability density function for the Gamma Distribution. By means of this model curve, we strategically forecast the future engineering manpower requirements to meet the Government's long range nuclear power plan. As a sensitivity analysis, the directions for the localization of nuclear power plant design engineering, are studied in terms of the performance factor for the experienced versus inexperienced engineers.

• Korean Journal of Applied Biomechanics
• /
• v.12 no.2
• /
• pp.109-130
• /
• 2002

The purpose of this paper was to make a comparative analysis for the difference of the various kinematic variation which is occurred in the each situation when pitchers throw a straight and a curve ball. Four pitchers, who are two national team players and two high level pitchers, were selected among the right over hand pitchers of D university in the Busan for this paper. The data were analyzed by using 3D equipment. The results of the analysis which was about the elapsed time of the pitching, the movement of the body center-point, the highest height of the left knee, stride length, knee joint angle, shoulder joint angle, elbow joint angle and wrist joint angle in the each section(ST, LKU, HBP, LCF, MCP, BRP) were as follows : 1. Pitching time in the each section and step in the pitching for straight and curve ball was similar. The total elapsed time of the straight and curve ball was 1.78${\pm}$0.07sec and 1.77${\pm}$0.11sec in the order. 2. The position change of the body center to the Z(above below) direction did not show significant difference in the each situation of the section and step between pitching for the straight and curve ball. 3. Height of the left knee did not show significant difference as 125.38${\pm}$11.85cm and 124.95${\pm}$11.63m in the each pitching motion for straight and curve ball. The rate(%H) between height and stride length showed 68.42${\pm}$5.53(%H), 68.40${\pm}$5.45(%H) in the each pitching motion. 4. Pitching for curve ball showed longer stride length than pitching for straight ball that as the stride length was 140.35${\pm}$4.96cm and 144.8${\pm}$1.69cm. The rate(%H) between height and stride length showed 76.9${\pm}$3.77(%H), 79.39${\pm}$2.23(%H) in the each pitching motion. 5. Left knee joint angle did not show significant difference in the ST, LKU and HBP section in the each pitching motion. However, it was shown that knee joint angle was flexed much more in the LFC, MCP and BRP section in the pitching for curve ball. 6. Right shoulder joint angle did not show significant difference in the ST, LKU and HSP section. However, when pitches threw a curve ball in the LKU section. In the LFC section, the right shoulder joint angle was extended much more in the pitching for curve ball, and the angle was extended much in the MCP and BRP section in the pitching for curve ball than straight ball. 7. Right elbow joint angle did not show significant difference in the ST, LKU and HRP section in the two pitching motion. The angle had more flexion in the LFC and MCP section in the pitching for curve ball than the pitching for straight ball. The angle in the each pitching motion for straight ball and curve ball were extended by a narrow margin in the BRP section. 8. Right wrist joint angle was extended much more in the LFC and MCP section in the pitching for curve ball. In the BRP section, the angle was extended much more in the pitching for straight ball than curve ball.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.5
• /
• pp.905-909
• /
• 2006

Recently various types of curved integral imaging system have been reported for improvement of viewing angle. However, the optical implementation has been limited to only unidirectional system. In this paper, we propose a curved integral imaging (CII) system with additional use of a large-aperture ten in conventional II system and explain a generation scheme of elemental images in the proposed system. The proposed system provides full-directional curvature effect and has simple structure due to the use of well-fabricated flat devices. For the full-directional-curved II system, we perform my analysis based on Johns matrix and synthesize novel elemental images. To show the usefulness of synthesized elemental images, preliminary experiments were performed and some experimental results were presented.

• The Korean Journal of Applied Statistics
• /
• v.27 no.1
• /
• pp.159-168
• /
• 2014

The news impact curve(NIC) originally proposed by Engle and Ng (1993) is a graphical representation of volatility for financial time series. The NIC is a simple but a powerful tool for identifying variability of a given time series. It is noted that the NIC is suited to symmetric volatility. Recently a lot of attention has been paid to asymmetric volatility models and therefore asymmetric version of the NIC would be useful in the field of financial time series. In this article, we propose to incorporate LASSO in constructing asymmetric NICs based on asymmetric GARCH models. In particular, bilinear GARCH models are considered and illustrated via KOSDAQ data.

• Proceedings of the Korean Information Science Society Conference
• /
• 2010.06b
• /
• pp.275-278
• /
• 2010

이 논문에서는, 기존에 존재하는 글자체의 커브 데이터를 분석하여 같은 글자를 붓글씨로 서예를 하듯이 다시 써낸 듯한 효과를 낼 수 있는 방법을 제안한다. 글자를 형성하는 위상적인 뼈대를 커브로 쪼개어, 글자 하나를 여러 획으로 분리하여 표현한 후에, 각 획에 해당하는 커브의 차원 수와, 길이와 곡률을 이용하여 붓의 궤적을 자동적으로 생성해 내는 방법이다. 붓의 궤적이 표현될 방법을 기존 글자 데이터를 이용해서 어떻게 조작 경로를 자동적으로 만들어 붓글씨 팔적을 생성해낼 것인지가 풀어내어야 할 문제이다.

• Journal of Korean Ophthalmic Optics Society
• /
• v.3 no.1
• /
• pp.33-37
• /
• 1998

Lens centration was the fitting variable that was most dependent on base curve radius. Flatter lenses tended to decenter more. A flatter contact lens will likely have to move into the periphery to reach this point of stability. In most cases, the decentration was in the superior and/or temporal direction. It was also found that comfort complains were more common with flatter lenses. The optimal fits was highest with the 8.4mm base curve lens for all three ranges fit eyes decreased as base curve radius was increased. These lenses with steeper radii lead to better centration and therefore to better fit and comfort for more patients than do thin lenses with flatter radii.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.12
• /
• pp.2664-2669
• /
• 2011

We proposed a new method to improve the resolution of far object image in curving effective integral imaging system. Basically, the curving effective integral imaging(CEII) system can improve the resolution of the reconstructed images with an increased sampling rate of elemental images. However, in the case when an object located far from the lenslet array is picked up, the low resolution of the reconstructed images of the far object has been a primary problem because the sampling rate is very low. In order to solve this drawback, by using the direct pixel mapping(DPM) method the EIA picked up from a far object is transformed into a new EIA that virtually looks like the EIA picked up from the object originally located close to the lenslet array. From this new EIA, highly resolution-enhanced images of far object could be reconstructed in the CEII system. To show the feasibility of the proposed method, simulation results are compared with the conventional method.

• The Transactions of the Korea Information Processing Society
• /
• v.1 no.4
• /
• pp.531-540
• /
• 1994

Spline curve scheme is the most valuable tool for the CAD of industrial products. Hence, the development of a new, effective curve scheme can have immediate impact on the current design industries. This paper develops and implements a new methodology for the implementation of the visually continuous class of splines which can produce a more flexible and diverse curve shapes. This class of splines has advantaged over existing splines in that it can accommodate wider range of shapes while maintaining the interpolators property of the ordinary cardinal splines. Most importantly, we avoid using the previous method of implementing G$^1$ curves, where users must specify scalar values for the control of curve shapes. We derive and implement an easy-to -use transformation between the user-specified graphical tangent vectors and the actual parameters for the resulting curve. Since the resulting curve shape reflects original tangential direction faithfully, CAD users can simply represent approximate curve shapes with proper tangents. Consequently, a simple user interface device such as a mouse can effectively produce a various spline curves using the proposed spline tool.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.1
• /
• pp.125-129
• /
• 2014

In this paper, design and fabrication of the GPS receiving antenna using Hilbert curve fractal structure was proposed. The size of the antenna was miniaturized by transforming dipole structure into monopole structure because its size increases if Hilbert curve fractal dipole structure is used. To use a Hilbert curve structure, the current directions of the radiator were made oppositely each other. The size of the antenna is $10{\times}10{\times}0.8[mm]$, the line width is 0.25[mm]. The resonant frequency is 1.58[GHz] and its range is 1.52[GHz] ~ 1.65[GHz]. Frequency bandwidth is 130[MHz]. Antenna maximum gain is 3.09[dBi].