• Journal of Advanced Marine Engineering and Technology
• /
• 제34권4호
• /
• pp.508-514
• /
• 2010

본 논문은 커먼레일 디젤엔진의 정속운전시 배출되는 나노크기의 입자상 물질을 분석하는데 초점을 두었다. 디젤산화촉매 후단에서 나노입자상 물질의 개수농도 저감수준은 크지 않았으나 매연여과장치 후단에서 분석한 결과 1,000배 정도 저감되는 결과를 확인하였다. 고속 고부하 조건에서는 매연여과장치의 자연재생 효과로 인해 입자상 물질은 증가하였다. 연료분사시기를 BTDC $6^{\circ}CA$ 에서 ATDC $4^{\circ}CA$까지 지각시킨 결과 입자상 물질의 개수농도는 감소하였지만 최지각 조건인 ATDC $9^{\circ}CA$에서는 증가하는 결과를 확인하였다. EGR 적용시 핵화모드 입자상 물질은 저감되는 경향을 보였으며 축적모든 입자는 증가하였다.

• 대한기계학회논문집B
• /
• 제35권2호
• /
• pp.137-143
• /
• 2011

본 연구는 4실린더 커먼레일 디젤엔진에 바이오디젤 혼합 디젤연료를 적용하였을 경우 엔진의 연소특성과 배출물 저감효과를 실험적으로 구한 것이다. 실험 연료는 바이오디젤 20%와 디젤연료 80%(체적분율)를 혼합한 BD20과 저유황디젤연료(ULSD)를 사용하였으며, 연료분사압과 엔진회전수를 변수로하여 실험을 수행하였다. 실험결과 B20과 ULSD 모두 연료분사압력이 증가함에 따라 NOx 배출농도는 증가하고, Soot 배출량은 감소하는 경향을 나타내었다. 특히 BD20의 경우 ULSD와 비교하여 NOx 배출농도는 다소 증가하였으나, Soot 배출량은 현저하게 감소하였다. 또한, 회전속도가 1000rpm에서 2000rpm으로 증가함에 따라 NOx 배출농도는 감소하고, Soot 배출량은 낮은 분사압력에서 현저히 증가하는 경향을 나타내었다.

• 한국자동차공학회논문집
• /
• 제23권6호
• /
• pp.623-632
• /
• 2015

This study proposes a control strategy of the common rail pressure with a fuel injection limitation algorithm to reduce particulate matter (PM) emissions under transient states. The proposed control strategy consists of two parts: injection quantity limitation and rail pressure adaptation. The injection limitation algorithm determines the maximum allowable fuel injection quantity to avoid rich combustion under transient states. The fuel injection quantity is limited by predicting the burned gas rate after combustion; however, the reduced injection quantity leads to deterioration of engine torque. The common rail pressure adaptation strategy is designed to compensate for the reduced engine torque. An increase of the rail pressure under transient states contributes to enhancement of the engine torque as well as reduction of PM emissions by promoting atomization of the injected fuel. The proposed control strategy is validated through engine experiments. The rail pressure adaptation reduced the PM emission by 5-10% and enhanced the engine torque up to 2.5%.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.75-81
• /
• 2005

An experimental study on homogeneous charge compression ignition combustion with direct fuel injection was conducted using a single cylinder common-rail diesel engine. To improve the homogeneity of fuel-air mixture, the premixed fuel (gasoline) was injected into premixing chamber and the diesel fuel was injected into the combustion chamber as an ignition source for the gasoline premixture. The experimental results show that soot emissions were dramatically reduced with the increase of fuel premixing ratio, however incomplete products such as HC and CO increased with the increase of the premixed ratio. Earlier injection of Dl diesel fuel increased the IMEP with the decrease of HC and CO concentrations.

• 한국분무공학회지
• /
• 제9권1호
• /
• pp.15-20
• /
• 2004

The post injection effect to enhance aftertreatment devices' performance is essential to meet future stringent emission standards by controlling exhaust gas temperature and emission pollutants. The test has been made with commercial common rail diesel engine by post injection manipulation, to optimize exhaust gas temperature while guarantee low fuel penalty. The optimization was done at 1500, 2000 and 2500[rpm] for 2, 4[bar] condition which show low exhaust gas temperature. The main purpose of this test is dedicated to understand mechanism of exhaust gas temperature rise while optimizing

• 한국분무공학회지
• /
• 제15권1호
• /
• pp.8-16
• /
• 2010

This paper present the diesel spray characteristics at different injection system parameters in a HSDI diesel engine. The spray characteristics was calculated by the coupled simulation of fuel injection system model and three-dimensional KIVA-3V code with TAB spray model. The relevant injection parameters are accumulator volume, control chamber initial volume, control orifice diameter, needle valve diameter and nozzle chamber initial volume, etc. Parametric investigation with respect to twelve relevant injection parameters showed that there was a significant advantage in varying control chamber initial volume, control chamber orifice diameter, and nozzle chamber orifice diameter with respect to effect the SMD and fuel injection speed. Consequently, in order to design the fuel injection system for spray characteristics, it seems reasonable to suppose to be optimized the fuel injection system.

• 한국자동차공학회논문집
• /
• 제15권5호
• /
• pp.78-85
• /
• 2007

Recently, diesel vehicles have been increased and their emission standards have been getting strict. The emission of diesel vehicles contains numerous dangerous compounds, especially particulate matters cause a serious environmental pollutant and affect to human health seriously. Thousands of studies have already reported that particulate matters are associated with respiratory and cardiovascular diseases, and death. Due to these, it is necessary to measure the soot concentration and soot particle size in laboratory flames or practical engines to recognize the soot formation, and develop the control strategies for soot emission. In this study, the characteristics of exhausted soot particle size and volume fraction from 2.0L CRDI diesel engine have been investigated as varying engine speed and load. Laser induced incandescence has been used to measure soot concentration. Time-resolved laser induced incandescence has been used to determine soot particle size in the engine. The soot volume fraction is increased as increasing engine load but soot volume fraction is decreased as increasing engine speed. The primary particle size is distributed about $35nm{\sim}60nm$ at each experimental conditions.

• 대한기계학회논문집A
• /
• 제37권12호
• /
• pp.1489-1495
• /
• 2013

유체의 고압유동은 여러 산업현장에 활용되고, 특히 그 중 내연기관의 연료분사 인젝터가 대표적이며 디젤엔진의 커먼레일 시스템의 경우 1000bar 이상의 압력이 사용된다. 이와 같이 고속으로 분출되는 유체유동의 경우, 노즐을 통해 분사되는 고속의 유체는 주위기체와의 상호작용으로 분열과정을 거치게 된다. 이 분열과정은 연소실 혼합기형성기과정에 영향을 주게 되며, 그 결과 엔진의 연소상태에 까지 영향을 미치게 된다. 따라서 연료분무의 분열과정에 대한 해석은 중요하며, 본 연구에서는 연료분무의 분열을 위한 수치해석 서브모델로 Reitz&Diwakar 및 CAB(Cascade atomization and breakup)모델을 사용하였다. 본 연구의 목적은 분사된 분무의 분열과정의 정확한 해석이며, 분사연료의 분열발생 형태의 빈도 등을 조사하였다. 결과로서 본 연구는 상용 CFD 프로그램(CFX)을 이용하여 디젤분무의 분열과정해석을 위한 적합한 분열모델을 제안한다.

• 한국분무공학회지
• /
• 제12권3호
• /
• pp.131-137
• /
• 2007

This is an experimental study on characteristics of engine performance and discharged materials in common-rail type diesel engine. The bio-diesel fuel is mixed with the diesel fuel in common use at the ratio of 20% or 100%. The diesel fuel and blended fuel is irradiated by ultrasonic wave energy. The diese1 fuel, blended fuel, reformed diesel fuel and reformed blended fuel by ultrasonic wave energy are applied to the experimental engine individually. The results are compared with one of the diesel fuel in common use and analyzed.

• 한국자동차공학회논문집
• /
• 제22권5호
• /
• pp.108-115
• /
• 2014

In this study, experimental approaching method was applied under and single-cylinder engine to research the performance of direct needle-driven piezo injector (DPI) for CR direct-injection. As key-point factor of this DPI that relies on direct-acting operating of injector needle, unlike conventional hydraulic-servo, its nozzle needle can be directly driven by piezo actuator. Thus, effect of direct-acting injection of DPI on diesel combustion and emission characteristics was investigated under common-rail single-cylinder direct-injection engine, equipped with three different driving mechanism, including indirect-acting solenoid, piezo and DPI system. As main results, it found that a direct-acting piezo injector has higher of IMEP. And it has higher heat release rate during premixed combustion and mixing controlled combustion phase due to its higher heat release, even though nitrogen oxide (NOx) formations were increased slightly.