ZnO:Al films with about 500 nm thick were prepared by RF magnetron sputtering. The ZnO:Al films were annealed at 100 ℃, 200 ℃, 300 ℃, and 400 ℃ for 10 h, respectively. The resistivity, carrier concentration, and mobility variation of ZnO:Al films with heat treatments were measured. The causes of the resistivity variation of ZnO:Al films with heat treatments were investigated by utilizing the results of x-ray diffraction and field emission scanning electron microscope. The energy band gap, Urbach energy, and refractive index were obtained from the transmittance of ZnO:Al films. The change in electrical properties of the ZnO:Al film was explained in relation to the optical properties.
Journal of the Institute of Electronics Engineers of Korea TE
/
v.37
no.5
/
pp.1-6
/
2000
We prepared organic light-emitting-diodes (LEDs) with a squarylium(Sq)-doped aluminum quinoline(Alq3) emission layer by the vapor deposition method. We discussed their electro-luminescence(EL) and electrical properties. The EL from Sq had a peak wavelength of 670nm and a half-width of 30nm. Only the EL from So(purely red) could be observed at the doping concentration of over 15mol%, but the luminance were low (0.21cd/$m^2$, 0.1cd/$m^2$) and EL efficiency was under the $10^{-2}$W. Although Sq molecules seemed to act as trap site in Alq3 molecules, they acted as carrier drafts site at doping concentration of over 5mol%.
ZnO:Al thin films deposited by RF magnetron sputtering were post-annealed and the electrical and optical properties of ZnO:Al thin films were investigated before and after anneling. We confirmed that the ZnO:Al thin film was affected by post-annealing temperature. As post-annealing temperature increases, crystallinity and transmittance in visible area (400~800 nm) of ZnO:Al thin films decreased. While sheet resistance of thin films increased sharply with increasing to $400^{\circ}C$. This result is due to reduce of carrier concentration caused by absorption of $O_2$ or $N_2$ at surface of thin film.
Proceedings of the Korean Vacuum Society Conference
/
2011.02a
/
pp.85-85
/
2011
RF magnetron co-sputtering을 이용하여 RF power 및 공정 압력에 따라 GZO 및 IGZO 박막을 유리기판 위에 제작하고 투명전극으로 구조적, 광학적, 전기적 특성을 조사하였다. 박막 증착 조건의 초기 압력은 $1.0{\times}10^{-6}Torr$, 증착온도는 상온으로 고정하였으며 기판은 Corning 1737 유리기판을 사용하였다. 소결된 타겟으로 ZnO, $In_2O_3$ 및 $Ga_2O_3$을 이용하였으며, 각각의 타겟은 독립 된 RF파워를 변화시키며 투명전극의 성분비를 조절하였으며, 증착 압력은 10 m에서 100 mTorr까지, 기판과의 거리는 25 mm에서 65 mm까지 변화시키며 박막을 제작하였다. 유리기판 위에 불순물이 첨가된 모든 ZnO 박막에서 (002) 면의 우선배향성이 관찰되었고, 3.4eV에서 3.5eV 정도의 광학적 밴드갭을 가지며 80% 이상의 투과율을 나타내었다. GZO 박막의 경우 증착 조건에 따라 투명전극에 요구되는 $5*10^{-3}{\Omega}-cm$ 이하의 전기적특성을 가짐을 보였으며, gallium 성분이 0%에서 6%로 증가함에 따라 3.3eV에서 3.5eV로 blue-shift하였으며, 비저항은 0.02에서 $0.005{\Omega}cm$로 낮아졌으며 이동도는 $4.7cm^2V^{-1}s^{-1}$에서 $2.7cm^2V^{-1}s^{-1}$로 보이며 GZO 물질이 투명전극으로서 기존의 ITO 물질 대체 가능성을 확인하였다. IGZO 박막은 In과 Ga의 함량에 따라 저항률의 변화가 크게 나타났으며, In의 함량이 많을수록 이동도, 캐리어 농도의 증가로 저항률은 감소하였다.
Proceedings of the Korean Vacuum Society Conference
/
2013.08a
/
pp.278.2-278.2
/
2013
그래핀은 우수한 전기적, 기계적, 광학적 특성들로 인하여 전자소자, 센서, 에너지 재료 등으로의 응용이 가능하다고 알려진 단 원자층의 탄소나노재료이다. 특히 그래핀을 전자소자로 응용하기 위해서는 캐리어 농도, 전하 이동도, 밴드갭 등의 전기적 특성을 향상시키거나 제어하는 것이 요구되며, 에너지 소재로의 응용을 위해서는 높은 전기전도도와 함께 기능화를 통한 촉매작용을 부여하여 효율을 향상시키는 것이 요구된다. 일반적으로 화학적 도핑은 그래핀의 전기적 특성을 제어하는 효율적인 방법으로 알려져 있다. 화학적 도핑의 방법으로 질소, 수소, 산소 등 다양한 이종원소를 열처리 또는 플라즈마 처리함으로써 그래핀을 구성하는 탄소원자를 이종원자로 치환하거나 흡착시켜 기능화 처리된 그래핀을 얻는 방법들이 제시되었다. 이중 플라즈마를 이용한 도핑방법은 저온에서 처리가 가능하고, 처리시간, 공정압력, 인가전압 등 플라즈마 변수를 변경하여 도핑정도를 비교적 수월하게 제어할 수 있다는 장점을 가지고 있다. 본 연구에서는 열화학기상증착법으로 합성된 그래핀을 직류 플라즈마로 처리함으로써 효율적인질소도핑 조건을 도출하고자 하였다. 그래핀의 합성은 200 nm 두께의 니켈 박막이 증착된 몰리브덴 호일을 사용하였으며, 원료가스로는 메탄을 사용하였다. 그래핀의 질소 도핑은 평행 평판형 직류 플라즈마 장치를 이용하여 암모니아($NH_3$) 플라즈마로 처리하였으며, 플라즈마 파워와 처리시간을 변수로 최적의 도핑조건 도출 및 도핑 정도를 제어하였다. 그래핀의 질소 도핑 정도는 라만 스펙트럼의 G밴드의 위치와 반치폭(Full width at half maximum; FWHM)의 변화를 통해 확인하였다. NH3 플라즈마 처리 후 G밴드의 위치가 장파장 방향으로 이동하며, 반치폭은 감소하는 것을 통해 그래핀의 질소도핑을 확인하였다.
Proceedings of the Materials Research Society of Korea Conference
/
2003.03a
/
pp.136-136
/
2003
카본나노튜브는 상용되는 기존의 센서에 비해 표면적이 넓어 감도가 놀고 응답속도가 빠르다. 또한 나노 스케일의 크기를 가지므로 고직접화를 실현할 수 있으며 기능복구성이 뛰어나 상온동작을 통한 저전력화가 가능하다. 본 실험에서는 아크방전법으로 합성한 카본나노튜브를 가스센서로 제작하여 상온에서 NH$_3$, NO 가스와의 반응 특성을 평가하였다. 또한 origin soot와 이를 정제한 purified CNT를 SEM(주사전자현미경), TEM(투과전자현미경), Raman scattering spectroscopy(라만 산란 분광기)를 통해 재료적 특성을 조사하고 이를 가스 감응 곡선과 연관하여 비교, 분석하였다. 전극에 CNT막을 형성시키기 위해 3g의 N,N dimethylformamide 용액에 CNT 10mg을 분산시킨 후 2시간동안 초음파 처리하였다. 이 용액을 mask를 이용해 전극 위에 막을 형성시킨 후 20$0^{\circ}C$에서 열처리하였다. 이렇게 제조된 origin soot와 purified CNT센서는 flow system을 이용하여 측정하였고 $N_2$분위기 하에서 센서를 안정화시킨 후 측정가스와의 반응을 살펴보았다 센서의 반응속도, 회복속도, 감도 등의 측정결과 origin soot는 NH$_3$ 25ppm에서 20%, purified CNT는 1%의 감도를 보여 20배 높은 감도를 보았다. NO 25ppm의 경우에도 origin soot가 8%, purified CNT는 0.8%의 감도를 보여 10배 높은 감도를 보였다. 이는 탄소입자가 많은 origin soot가 purified CNT 보다 표면적이 넓어 보다 많은 가스 흡착 싸이트를 가지기 때문이다. 하지만 origin soot는 반응시간과 회복속도가 Purified CNT 보다 2배 이상 느려 표면적 증가에 따른 가스 흡착과 탈착 능력이 떨어짐을 알 수 있었다. 또한 CNT와 가스사이의 전하 이동 방향에 따라 NH$_3$는 양의 감도를 NO는 음의 감도를 보였다 이는 전하의 이동 방향에 따라 전하와 캐리어 사이의 결합 및 해리가 일어나게 되고 결국 카본나노튜브 내의 캐리어 수를 증감시킴에 따라 나타나는 현상이다. 이러한 가스의 감도는 농도에 따라 증가하였으며 origin soot를 이용하여 1ppm이하의 NH$_3$ 가스를 검출할 수 있었다.
Proceedings of the Korean Institute of Information and Commucation Sciences Conference
/
2011.05a
/
pp.702-705
/
2011
Poly-Si wafers with resistivity of 1 [${\Omega}$-cm[ and thickness of 50 [${\mu}m$] were used as a starting material. Various efficiency influencing parameters such as rear surface recombination velocity and minority carrier diffusion length in the base region, front surface recombination velocity, junction depth and doping concentration in the Emitter layer, BSF thickness and doping concentration were investigated. Optimized cell parameters were given as rear surface recombination of 1000 [cm/sec], minority carrier diffusion length in the base region 50 [${\mu}m$], front surface recombination velocity 100 [cm/sec], sheet resistivity of emitter layer 100 [${\Omega}/{\Box}$], BSF thickness 0.5 [${\mu}m$], doping concentration $5{\times}10^{19}\;cm^{-3}$. Among the investigated variables, we learn that a diffusion length of base layer acts as a key factor to achieve conversion efficiency higher than 19.8 %. Further details of simulation parameters and their effects to cell characteristics are discussed in this paper.
Journal of the Korean Institute of Telematics and Electronics
/
v.21
no.3
/
pp.60-65
/
1984
In this paper, we have used symmetrical GaAs/(Ga, Al) As DH-LED as a model for the optimization of frequency response which is the most important design parameter of the optical communication-LED. And optimum design parameters have been chosen to improve performance factors of the DH-LED by computer simulation. This is for the purpose of systematic consideration of the interrelation of the physical parameters such as impurity concentration of the active layer, thickness of the active layer, minority carrier lifetime, space charge capacitance and injected current density.
HVPE(hydride vapor phase epitaxy)법을 이용하여 C(0001)면의 사파이어 기판위에 GaN 박막을 성장하였다. 110$0^{\circ}C$의 온도에서 박막의 성장률은 120$\mu\textrm{m}$/hr이었고, 사파이어 기판과 GaN사이의 격자상수와 열팽창계수차로 인하여 많은 크랙이 존재하였다. 두께가 20$\mu\textrm{m}$인 GaN의 (0002)면에 대한 X-선 회절피크의 반치폭은 576초 이었다. 10K의 온도에서 측정된 광루미네센스 스펙트럼에서는 강한 강도의 속박여기자에 의한 피크(I2)와 약한 강도의 도너-억셉터 쌍 사이의 재결합에 의한 피크가 나타났으며, 깊은 준위로부터의 발광은 검출되지 않았다. GaN 박막의 전기전도형은 n형 이었고, 전자이동도와 캐리어농도는 각각 72$\textrm{cm}^2$/V-sec와 6x1018cm-3이었다.
Ji, Seon-Beom;Kim, Sun-Jae;Park, Hyun-Sang;Han, Min-Koo
Proceedings of the KIEE Conference
/
2009.07a
/
pp.1281_1282
/
2009
ICP-CVD를 이용하여 inverted staggered 구조를 갖는 미세결정 실리콘 (Nanocrystalline Silicon, nc-Si) 박막 트랜지스터(Thin Film Transistor, TFT)를 제작하였다. 또한, 소자의 특성과 전기적 안정성을 평가하였다. 실험 결과는 짧은 채널 길이를 갖는 nc-Si TFT가 긴 채널 길이의 소자보다 같은 드레인 전압 바이어스 하에서 덜 열화 됨을 알 수 있었다. 이는 드레인 전압 바이어스 하에서의 낮은 채널 캐리어 농도는 적은 defect state를 만들기 때문으로 짧은 채널 길이의 TFT가 긴 채널 길이의 TFT보다 $V_{TH}$ 열화가 적었다. 이러한 결과는 짧은 채널 길이의 nc-Si TFT가 디스플레이 분야에 있어 다양하게 응용될 것으로 기대된다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.