• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.12 s.115
• /
• pp.1240-1248
• /
• 2006

This paper presents an UHF band(911 MHz) RFID tag antenna which has near-isotropic radiation pattern and easy conjugate impedance matching characteristics to any commercial chips of usual practice through the application of an inductively-coupled feeding. The proposed antenna of compact size $40{\times}46mm\;(0.12{\times}0.14{\lambda})$ has, at normal incidence, the maximum RCS of $-18.5dBm^2$ and the 3 dB RCS bandwidth of 9 MHz(1 %) in case of short chip load. It has the maximum and minimum RCS' of $-16.9dBm^2\;and\;-21.4dBm^2$ depending on the incident angles. The difference of about 4.5 dB is relatively small compared with that (about 70 dB) of a pure dipole antenna. The designed antenna has been fabricated and its RCS' have been measured varying the angles of incidence. The measured RCS' have been found to have good agreement with the simulated ones.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.6B
• /
• pp.1127-1135
• /
• 2000

The beamforming procedure in Adaptive Array Antenna System is affected by signal degradation and data rate due to DS-CDMA characteristics. Until this time, a lot of techniques are suggested to overcome this problems. This paper shows the simulation result about the beamforming performance of symbol level system that process slow data rate, compensated signal by despreading procedure in front of beamformer, and that of chip level system that process chip level signal without it. we analysis the performance using MSE, beam pattern, scattering points of beamformer output. chip level system is superior to symbol level system in time varying channel, while the performance of them didn't have difference in static channel.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.156-161
• /
• 2006

In this paper, GPS/IMT2000/Wireless LAN compact chip antenna is designed for mobile communication system. The proposed antenna size is $10.2mm{\times}21mm{\times}1mm$. It consists of three meander lines. dual resonance frequencies is achieved by two effective current paths using two meander lines and via. also The parasitic meander line structure is added. The coupling is adjusted by arranging parasitic meander line for triple-band. The fabricated antenna achieve triple-band. The resonance frequencies are 1.672GHz, 2.092GHz, 2.504GHz. The impedance bandwidths of each resonance frequencies are 156MHz, 272MHz, 64MHz. The maximum radiation gains of fabricated antenna are 0.08dBi, 1.67dBi, -1.44dBi. The proposed antenna achieve quasi monopole radiation pattern.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.2 s.93
• /
• pp.211-216
• /
• 2005

In this paper, GPS/PCS/Satellite DMB compact chip antenna is designed using stacked meander line for mobile communication handset. The fabricated antenna size is $12.52mm\times19.95\times1.05mm$. The coupling is adjusted by via and arrangement among meander lines to improve FR(Frequency Ratio) and return-loss. The fabricated antenna achieve triple-band. The resonance frequencies are 1.696 GHz, 1.888 GHz and 2.680 GHz. The impedance bandwidths are 150 MHz, 120 MHz and 60 MHz. The maximum gains of antenna are 0.08 dBi, 1.70 dBi and -1.27 dBi at resonance frequencies.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.8
• /
• pp.765-768
• /
• 2015

In this paper, two ports feeding a microstrip patch antenna using a quadrature hybrid circuit was proposed to enhance the bandwidth for the global positioning system(GPS). The square patch was designed, and the probe feeding was applied. The quadrature hybrid chip circuit for two-port feeding was designed, and output ports that have a 90-degree phase difference feed to the patch antenna. The designed patch and quadrature hybrid circuit were implemented on an FR4 board, and were combined. The measurement of the bandwidth within a voltage standing wave ratio(VSWR) of 2: 1 and axial ratio(AR) in 3dB were 29 %BW(1,230~1,700 MHz) and 15.87 %BW(1,400~1,650 MHz), respectively. The peak gain at the GPS center frequency was measured at 2.75 dBi in an anechoic chamber.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.59-60
• /
• 2017

In this paper, we studied a design method for obtaining broadband property by loading a chip capacitor on a coplanar waveguide(CPW)-fed compact quasi-Yagi antenna(QYA). The proposed antenna is a three-element QYA with dipole, reflector, and director. To reduce the size, the ends of both dipole and reflector are bent, and balun is incorporated in the antenna. To improve impedance matching, the loading position and capacitance value of chip capacitor were determined. From some simulations, the proposed antenna using an FR4 substrate with a size of 90 mm by 90 mm was designed for the operation in a broadband covering the UHF RFID and GPS systems. The antenna showed a good performance with a broadband of 850-1,626 MHz(62.7%) for a VSWR ${\leq}2$, a gain ${\geq}3dBi$, and a frong-to-back ratio ${\geq}4.6dB$.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.2
• /
• pp.135-140
• /
• 2008

In this paper, the spiral antenna with the center frequencies of 315MHz, 433MHz, and 447MHz for RKE system of a vehicle is designed on PCB. The antenna is microstrip line-fed, and applied PIFA concept near the feeding part to easily tune center frequency and input impedance. The PIFA-type spiral antenna with the size of $30mm{\times}20mm$ is designed on printed PCB by considering the effect of circuits and components on PCB, ECU case and vehicle body. Also chip inductor inserted dual-band spiral antenna of 315MHz and 447MHz is designed. We found that the antenna designed on PCB satisfied the antenna specifications through measurement and field test.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.4
• /
• pp.203-211
• /
• 2013

UHF RFID tag designers usually ndde the chip impedance and read power sensitivity value obtained when a tag chip is mounted on a chip pad. The chip impedance, however, is not able to be supplied by chip manufacturer, since the chip impedance is varied according to tag designs and fabrication processes. Instead, the chip makers mostly supply the chip impedances measured on the bare dies. This study proposes a chip impedance and read power sensitivity evaluation method which requires a few simple auxiliary and some RF measuring equipment. As it is impractical to measure the chip impedance directly at mounted chip terminals, some form test fixture is employed and the effect of the fixture is modeled and de-embeded to determine the chip impedance and the read power sensitivity. Validity and accuracy of the proposed de-embed method are examined by using commercial RFID tag chips as well as a capacitor and a resistor the value of which are known.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.05a
• /
• pp.57-58
• /
• 2018

In this paper, we studied a design method for a quasi-Yagi antenna operating over a broad bandwidth covering the UHF RFID(902-928 MHz) and GNSS(1,164-1.605 MHz). The proposed antenna is composed of three elements(dipole, reflector, and director) and fed by a coplanar waveguide. To reduce its size, a balun is integrated inside the antenna, and the ends of both the dipole and reflector are bent. Broadband impedance matching was obtained by placing the director near to the dipole and loading a chip capacitor inside the antenna. The antenna, designed through simulations, was fabricated on an FR4 substrate with 0.8 mm thickness. The experiment results for the antenna characteristics agree very well with the simulation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.12 s.103
• /
• pp.1206-1212
• /
• 2005

In this paper, we propose a novel antenna structure which uses the electric and magnetic currents so as to eliminate nulls on their radiation pattern. The tag antenna was matched to the conjugate impedance of the commercial tag chip using the modified double T matching network. The radiation efficiency is about $90\%$, and the bandwidth($S_{11}< -10 dB$) is 848${\~}$926 MHz. Also it shows the gain deviation between the maximum and minimum gains about 4 dB at any direction of the tag antenna at the operating frequency. The readable range of the tag is 1.7${\~}$2.4 m for an arbitrary rotation angle of the tag with a commercial tag chip.